38649
1.INSTALL WINCH CONTROL WIRE
Install the winch control wire with the 2 nuts.
52542A
2.INSTALL FRONT BUMPER NO. 2 PROTECTOR
When installing the front bumper No. 2 protector, heat the rear bumper cover using a heat light.
| Item | Temperature |
|---|---|
| Front Bumper Cover | 20 to 30°C (68 to 86°F) |
Do not heat the front bumper cover excessively.
When using a new front bumper cover:
Clean the surface of a new front bumper cover.
Using a heat light, heat the front bumper cover surface.
When reusing the front bumper cover:
Using a heat light, heat the front bumper cover surface.
Remove the double-sided tape from the front bumper cover.
Wipe off any tape adhesive residue with cleaner.
Install 2 new front bumper No. 2 protectors.
Remove the peeling paper from the face of 2 new front bumper No. 2 protectors.
After removing the peeling paper, keep the exposed adhesive free from foreign matter.
Align the front bumper No. 2 protector with the mark-off line of the rear bumper cover and install it as shown in the illustration.
Press the front bumper No. 2 protector firmly to install it.
| *a | Mark-off Line |
52421A
3.INSTALL FRONT BUMPER PAD
When installing the front bumper pad, heat the rear bumper cover using a heat light.
| Item | Temperature |
|---|---|
| Front Bumper Cover | 20 to 30°C (68 to 86°F) |
Do not heat the front bumper cover excessively.
When using a new front bumper cover:
Clean the surface of a new front bumper cover.
Using a heat light, heat the front bumper cover surface.
When reusing the front bumper cover:
Using a heat light, heat the front bumper cover surface.
Remove the double-sided tape from the front bumper cover.
Wipe off any tape adhesive residue with cleaner.
Install 4 new front bumper pad.
Remove the peeling paper from the face of 4 new front bumper pad.
After removing the peeling paper, keep the exposed adhesive free from foreign matter.
Install the front bumper pad as shown in the illustration.
Press the front bumper pad firmly to install it.
52126A
4.INSTALL FOG LIGHT MOUNTING BRACKET LH (w/ Fog Light)
Attach the 3 claws to install the fog light mounting bracket LH.
52125A
5.INSTALL FOG LIGHT MOUNTING BRACKET RH (w/ Fog Light)
Use the same procedure described for the LH side.
52128B
6.INSTALL FRONT BUMPER HOLE COVER LH (w/ Fog Light)
Attach the 4 claws to the front bumper hole cover LH.
Install the screw.
Attach the 2 guides to the fog light bracket LH.
Install the 3 screws.
52127D
7.INSTALL FRONT BUMPER HOLE COVER RH (w/ Fog Light)
Use the same procedure described for the LH side.
53104A
8.INSTALL LOWER RADIATOR GRILLE SUB-ASSEMBLY LH
Attach the 10 claws to install the lower radiator grille sub-assembly LH.
Install the 3 clips.
53103A
9.INSTALL LOWER RADIATOR GRILLE SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
75111
10.INSTALL FRONT LICENSE PLATE BRACKET
Install the front license plate bracket with the 2 nuts.
82114
11.INSTALL NO. 4 ENGINE ROOM WIRE (w/ Fog Light)
Attach the 10 clamps to install the No. 4 engine room wire.
81220
12.INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light)
81210
13.INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light)
Use the same procedure described for the LH side.
52149
14.INSTALL FRONT BUMPER INNER BRACKET (w/ Fog Light)
Attach the 3 claws and install the front bumper inner bracket.
53101
15.INSTALL RADIATOR GRILLE SUB-ASSEMBLY