Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER(for Standard) › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052857 EXTERIOR PANELS / TRIM _0255835 FRONT BUMPER(for Standard) A

EXTERIOR PANELS / TRIM  FRONT BUMPER(for Standard)  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

When installing the front bumper protector, heat the front bumper surface using a heat light.


Standard Heating Temperature:
Item Temperature
Front Bumper 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the front bumper excessively.


PROCEDURE

Hide 52542A 1.INSTALL FRONT NO. 2 BUMPER PROTECTOR

a.

Clean the front bumper surface.

i.

Using a heat light, heat the front bumper cover surface.


ii.

Remove the double-sided tape from the front bumper cover.


iii.

Wipe off any tape adhesive residue with cleaner.



b.
B302162

Install a new front No. 2 bumper protector.

i.

Remove the peeling paper from the face of 2 new front No. 2 bumper protectors.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



ii.

Install the 2 front No. 2 bumper protectors as shown in the illustration.



Hide 52411 2.INSTALL FRONT BUMPER GUARD (w/ Garnish)

a.

Attach the 6 clips to install the front bumper guard.


b.

Install the 4 nuts.


Hide 52114A 3.INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET (w/ Bracket)

a.

Attach the 2 claws.


b.

Install the front bumper extension mounting bracket with the 2 bolts.


Hide 53112E 4.INSTALL LOWER NO. 1 RADIATOR GRILLE

a.

Attach the 16 claws to install the lower No. 1 radiator grille.


b.

Install the 4 retainers.


Hide 52128B 5.INSTALL FRONT BUMPER HOLE COVER LH (w/ Fog Light)

a.

Attach the 5 claws to the front bumper hole cover LH.


b.

Install the 2 screws and 2 retainers.


Hide 52127D 6.INSTALL FRONT BUMPER HOLE COVER RH (w/ Fog Light)

HINT:

Use the same procedure described for the LH side.


Hide 52128B 7.INSTALL FRONT BUMPER HOLE COVER LH (w/o Fog Light)

a.

Attach the 5 claws to the front bumper hole cover LH.


b.

Install the screw and 2 retainers.


Hide 52127D 8.INSTALL FRONT BUMPER HOLE COVER RH (w/o Fog Light)

HINT:

Use the same procedure described for the LH side.


Hide 81220 9.INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light)

Hide 81210 10.INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light)

HINT:

Use the same procedure described for the LH side.


Hide 52149 11.INSTALL FRONT BUMPER INNER BRACKET (w/ Fog Light)

a.

Attach the 3 claws and install the front bumper inner bracket.


Hide 89348A 12.INSTALL NO. 2 ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

Hide 89341A 13.INSTALL NO. 1 ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

Hide 89348D 14.INSTALL ULTRASONIC SENSOR CLIP (w/ TOYOTA Parking Assist-sensor System)

Hide 82114 15.INSTALL NO. 4 ENGINE ROOM WIRE

a.

w/o TOYOTA Parking Assist-sensor System, w/ Fog Light:

Install the No. 4 engine room wire.

i.

Attach the 11 clamps to install the No. 4 engine room wire.


ii.

Connect the 2 connectors.



b.

w/ TOYOTA Parking Assist-sensor System, w/ Fog Light:

Install the No. 4 engine room wire.

i.

Attach the 12 clamps to install the No. 4 engine room wire.


ii.

Connect the 4 connectors.



c.

w/ TOYOTA Parking Assist-sensor System, w/o Fog Light:

Install the No. 4 engine room wire.

i.

Attach the 12 clamps to install the No. 4 engine room wire.


ii.

Connect the 2 connectors.



Hide 85208A 16.INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System)

Hide 85207A 17.INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

HINT:

Use the same procedure described for the LH side.


Hide 85045 18.INSTALL TYPE 1 HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY LH (w/ Headlight Cleaner System)

Hide 85044 19.INSTALL TYPE 1 HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

HINT:

Use the same procedure described for the LH side.