52412
1.INSTALL FRONT BUMPER NO. 2 GUARD (w/ Garnish)
Attach the 15 claws to install the front bumper No. 2 guard.
Install the 2 clips.
52435
2.INSTALL FRONT BUMPER GUARD GARNISH (w/ Garnish)
Attach the 6 guides to install the front bumper guard garnish.
Install the 4 clips.
52411
3.INSTALL FRONT BUMPER GUARD (w/ Garnish)
Attach the 4 claws to install the front bumper guard.
Install the 6 nuts.
52114A
4.INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET (w/ Bracket)
Attach the 2 claws.
Install the front bumper extension mounting bracket with the 2 bolts.
52542A
5.INSTALL FRONT BUMPER NO. 2 PROTECTOR
When installing the front bumper No. 2 protector, heat the rear bumper cover using a heat light.
| Item | Temperature |
|---|---|
| Front Bumper Cover | 20 to 30°C (68 to 86°F) |
Do not heat the front bumper cover excessively.
When using a new front bumper cover:
Clean the surface of a new front bumper cover.
Using a heat light, heat the front bumper cover surface.
When reusing the front bumper cover:
Using a heat light, heat the front bumper cover surface.
Remove the double-sided tape from the front bumper cover.
Wipe off any tape adhesive residue with cleaner.
Install 2 new front bumper No. 2 protectors.
Remove the peeling paper from the face of 2 new front bumper No. 2 protectors.
After removing the peeling paper, keep the exposed adhesive free from foreign matter.
Align the front bumper No. 2 protector with the mark-off line of the rear bumper cover and install it as shown in the illustration.
Press the front bumper No. 2 protector firmly to install it.
| *a | Mark-off Line |
52421A
6.INSTALL FRONT BUMPER PAD
When installing the front bumper pad, heat the rear bumper cover using a heat light.
| Item | Temperature |
|---|---|
| Front Bumper Cover | 20 to 30°C (68 to 86°F) |
Do not heat the front bumper cover excessively.
When using a new front bumper cover:
Clean the surface of a new front bumper cover.
Using a heat light, heat the front bumper cover surface.
When reusing the front bumper cover:
Using a heat light, heat the front bumper cover surface.
Remove the double-sided tape from the front bumper cover.
Wipe off any tape adhesive residue with cleaner.
Install 4 new front bumper pad.
Remove the peeling paper from the face of 4 new front bumper pad.
After removing the peeling paper, keep the exposed adhesive free from foreign matter.
Install the front bumper pad as shown in the illustration.
Press the front bumper pad firmly to install it.
52126A
7.INSTALL FOG LIGHT MOUNTING BRACKET LH (w/ Fog Light)
Attach the 3 claws to install the fog light mounting bracket LH.
52125A
8.INSTALL FOG LIGHT MOUNTING BRACKET RH (w/ Fog Light)
Use the same procedure described for the LH side.
52128B
9.INSTALL FRONT BUMPER HOLE COVER LH (w/ Fog Light)
Attach the 4 claws to the front bumper hole cover LH.
Install the screw.
Attach the 2 guides to the fog light bracket LH.
Install the 3 screws.
52127D
10.INSTALL FRONT BUMPER HOLE COVER RH (w/ Fog Light)
Use the same procedure described for the LH side.
53104A
11.INSTALL LOWER RADIATOR GRILLE SUB-ASSEMBLY LH
Attach the 10 claws to install the lower radiator grille sub-assembly LH.
Install the 3 clips.
53103A
12.INSTALL LOWER RADIATOR GRILLE SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
82114
13.INSTALL NO. 4 ENGINE ROOM WIRE
Attach the 10 clamps to install the No. 4 engine room wire.
89341A
14.INSTALL NO. 1 ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)
81220
15.INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light)
81210
16.INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light)
Use the same procedure described for the LH side.
52149
17.INSTALL FRONT BUMPER INNER BRACKET (w/ Fog Light)
Attach the 3 claws and install the front bumper inner bracket.
85271C
18.INSTALL HEADLIGHT CLEANER HOSE
85208A
19.INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System)
85207A
20.INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System)
Use the same procedure described for the LH side.
85341A
21.INSTALL HEADLIGHT CLEANER WASHER NOZZLE COVER LH (w/ Headlight Cleaner System)
85341A
22.INSTALL HEADLIGHT CLEANER WASHER NOZZLE COVER RH (w/ Headlight Cleaner System)
Use the same procedure described for the LH side.
53101
23.INSTALL RADIATOR GRILLE SUB-ASSEMBLY