Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › BLACK OUT TAPE (for Rear Door) › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052857 EXTERIOR PANELS / TRIM _0255852 BLACK OUT TAPE(for Rear Door) A

EXTERIOR PANELS / TRIM  BLACK OUT TAPE(for Rear Door)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

When installing the black out tape and window frame moulding, heat the vehicle body, black out tape and window frame moulding using a heat light.



Standard Heating Temperature:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Black Out Tape 20 to 30°C (68 to 86°F)
Window Frame Moulding 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the vehicle body, black out tape and window frame moulding excessively.


PROCEDURE

Hide 1.REPAIR INSTRUCTION

a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.


ii.

Wipe off any tape adhesive residue with cleaner.



b.

Installation temperature

i.

When the ambient temperature is below 15°C (59°F), perform the installation procedure after warming the vehicle body surface (installation surface of the door frame) and tape up to between 20 and 30°C (68 and 86°F) using a heat light. When the ambient temperature is above 35°C (95°F), cool the vehicle body surface (installation surface of the door frame) and tape down to between 20 and 30°C (68 and 86°F) prior to installation.

HINT:
·

The most appropriate temperature for installing the tape is 25°C (77°F).

·

When the temperature is low, the tape turns stiff and falls off easily. When the temperature is high, the tape loses elasticity.





c.

Before installation

i.

Make sure any dirt on and around the vehicle body surface where the tape will be installed (installation surface of the door frame) is removed, and that the surface is smooth. If the surface is rough or dirt remains when pressing the tape onto the surface, air will be trapped under the tape and result in a poor appearance.

HINT:

Spray water on the shop floor to settle any dust.




d.

Key points for handling the tape

i.

The tape bends and rolls up easily. Store the tape between flat pieces of cardboard or other similar objects and keep it dry and level.

NOTICE:

Do not bend the tape or leave it in high temperature places.




e.

Key points for the installation of the tape (how to use a squeegee and the installation procedure for flat surfaces)

NOTICE:
·

Position the tape with a high level of accuracy to achieve a neat finish and to avoid peeling.

·

The tape cannot be reused because it deforms and will not fit after removal.



i.

To avoid air bubbles, slightly raise the part of the tape that is going to be applied so that its adhesive surface does not touch the vehicle body while applying the tape. Tilt the squeegee at 40 to 50° (for pressing forward) or 30 to 45° (for pulling) to the vehicle body surface and press the tape onto the vehicle body surface with a force of 20 to 30 N (2 to 3 kgf) at a constant slow speed of 3 to 7 cm (1.2 to 2.8 in.) per second.

B147252E31
0.104,0.083 3.417,1.583 3.313,1.5 2.24,0.24 2.177,0.24 2.177,0.24 2.031,0.698 false 1.396,1.146 1.396,1.302 false 0.896,0.542 0.813,0.542 0.813,0.542 0.698,0.729 false 1.625,2.063 1.625,2.344 false 5,2.625 4.792,2.625 false 1.833,3.552 1.99,3.552 false 5.406,3.49 5.563,3.49 false 1.677,3.219 1.552,3.052 1.552,3.052 1.458,3.052 false 5.167,3.198 5.094,3.115 5.094,3.115 4.76,3.115 false 0.167,0.104 1.115,0.396 0.948,0.292 10 false Sectional View 2.281,0.146 3.417,0.458 1.135,0.313 10 false Non-padded Side 0.969,1.323 1.813,1.615 0.844,0.292 10 false Padded Side 0.979,0.469 1.635,0.76 0.656,0.292 10 false Squeegee 0.135,1.667 0.969,2.031 0.833,0.365 10 false For pressing forward: 3.698,1.688 4.635,1.979 0.938,0.292 10 false For pulling: 1.333,2.385 1.99,2.677 0.656,0.292 10 false Squeegee 4.156,2.531 4.813,2.823 0.656,0.292 10 false Squeegee 1.75,1.635 2.396,1.927 0.646,0.292 10 false 40 to 50° 5.083,2.813 5.656,3.01 0.573,0.198 10 true 30 to 45° 0.896,3.469 1.865,3.688 0.969,0.219 10 false Release Paper 4.469,3.406 5.448,3.646 0.979,0.24 10 false Release Paper 0.469,2.969 1.531,3.198 1.063,0.229 10 false Black Out Tape 0.354,2.219 1.292,2.438 0.938,0.219 10 false 3 to 7 cm/sec. 3.875,2.24 4.823,2.448 0.948,0.208 10 false 3 to 7 cm/sec. 2.479,2.896 3.354,3.125 0.875,0.229 10 false 10 to 20 mm 5.917,2.552 6.896,2.802 0.979,0.25 10 false 10 to 20 mm 3.76,3.031 4.792,3.25 1.031,0.219 10 false Black Out Tape

NOTICE:

Be sure to observe the specified pressing speed, force, and angle of the squeegee to avoid wrinkles or air bubbles.


HINT:
·

Either angle of the squeegee (for pressing forward or for pulling) is acceptable.

·

Be sure to apply the tape while removing the release paper 10 to 20 mm (0.393 to 0.787 in.) from the edge of the squeegee.





f.

Key points for the installation of the tape (how to use a squeegee and the installation procedure for hemming surfaces)

i.
B147253E19
1.188,0.708 1.021,0.208 1.021,0.208 0.917,0.208 false 0.719,0.646 1.073,0.917 0.354,0.271 10 false Third 1.677,0.417 2.198,0.688 0.521,0.271 10 false Second 2.448,0.646 2.771,0.906 0.323,0.26 10 false First 0.281,0.125 0.938,0.396 0.656,0.271 10 false Squeegee 1.625,1.781 1.969,2.042 0.344,0.26 10 false Hem

If it is difficult to press the tape, press it in several steps as shown in the illustration. Use your fingers or the padded surface of a squeegee to slowly apply the tape to the hem of the vehicle, especially for a small hem.

HINT:

When applying tape to the backside of a hem, remove the release paper and use your fingers or the padded surface of a squeegee.




g.

Key points for the installation of the tape (how to use a squeegee and the installation procedure for corners)

i.

Remove the release paper and apply the tape carefully with your fingers.


ii.

Before applying the tape to each corner, heat the tape using a heat light and gradually apply it to avoid wrinkles on the tape and achieve a neat finish.



h.

Check after installation

i.

After completing the application, check if the tape is applied neatly. If the tape is not applied neatly, apply new tape.

NOTICE:

Do not reuse the tape.




Hide 75954A 2.INSTALL REAR INNER BLACK OUT TAPE LH

B182619

a.

Refer to the illustration to position a new rear inner black out tape.


b.

Remove the release paper and apply the tape.


Hide 75938 3.INSTALL UPPER INNER BLACK OUT TAPE LH

B182623

a.

Refer to the illustration to position a new upper inner black out tape.


b.

Remove the release paper and apply the tape.


Hide 75936A 4.INSTALL NO. 6 BLACK OUT TAPE LH

B182621

a.

Refer to the illustration to position a new No. 6 black out tape.


b.

Remove the release paper and apply the tape.


Hide 75924C 5.INSTALL NO. 2 BLACK OUT TAPE LH

B182617E02
1.771,0 1.906,0.156 0.135,0.156 10 false a 1.76,0.354 1.948,0.51 0.188,0.156 10 false a 2.469,0.656 2.646,0.813 0.177,0.156 10 false b 2.896,0.594 3.073,0.75 0.177,0.156 10 false b 0.146,1.833 0.417,2.021 0.271,0.188 10 false a-a 1.854,1.833 2.156,2.01 0.302,0.177 10 false b-b 1.208,2.146 1.438,2.354 0.229,0.208 10 false A 1.156,2.823 1.427,3.083 0.271,0.26 10 false B 2.219,2.208 2.365,2.51 0.146,0.302 10 false C 2.938,1.948 3.125,2.208 0.188,0.26 10 false D

a.

Refer to the illustration to position a new No. 2 black out tape.

Standard Dimension:
Area Dimension
A 2 to 4 mm (0.078 to 0.158 in.)
B 4 to 6 mm (0.158 to 0.236 in.)
C 4 to 6 mm (0.158 to 0.236 in.)
D 2 to 4 mm (0.078 to 0.158 in.)



b.

Remove the release paper and apply the tape.


Hide 67872 6.INSTALL REAR DOOR WEATHERSTRIP LH

B184536

a.

Attach the 4 clips and install the upper part of the rear door weatherstrip.


Hide 67676C 7.INSTALL REAR NO. 2 DOOR FRAME GARNISH LH

Hide 67674A 8.INSTALL REAR DOOR FRAME GARNISH LH

Hide 75762A 9.INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING LH

Hide 75740 10.INSTALL REAR DOOR BELT MOULDING ASSEMBLY LH

Hide 68104 11.INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH

Hide 68124C 12.INSTALL REAR DOOR QUARTER WINDOW GLASS LH

Hide 67408F 13.INSTALL REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY LH

Hide 68152C 14.INSTALL REAR DOOR GLASS RUN LH

Hide 67842E 15.INSTALL REAR DOOR SERVICE HOLE COVER LH

Hide 68174C 16.INSTALL REAR INNER DOOR GLASS WEATHERSTRIP LH

Hide 67604 17.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

Hide 74611C 18.INSTALL ASSIST GRIP COVER LH

Hide 74280 19.INSTALL REAR DOOR ARMREST BASE PANEL ASSEMBLY LH

Hide 69278C 20.INSTALL REAR DOOR INSIDE HANDLE BEZEL LH

Hide 21.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).