Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › from 2015.08
RM2660E _56 Audio / Visual / Telematics _052831 PARK ASSIST / MONITORING _0255516 BLIND SPOT MONITOR SYSTEM Y

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the blind spot monitor system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
HINT:

If there are any scratches or impact marks on the rear bumper, perform the blind spot monitor beam axis confirmation. If any abnormalities are found, perform the blind spot monitor sensor installation condition inspection.


Result:
Proceed to
NEXT



NEXT

3.INSPECT BATTERY VOLTAGE
3.INSPECT BATTERY VOLTAGE
a.

Measure the battery voltage.

Standard Voltage:

11 to 14 V


If the voltage is below 11 V, replace or recharge the battery before proceeding to the next step.


Result:
Proceed to
NEXT



NEXT

4.CHECK CAN COMMUNICATION SYSTEM*
4.CHECK CAN COMMUNICATION SYSTEM*
a.

Use the GTS to check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>DIAGNOSTIC TROUBLE CODE CHART


Result:
Result Proceed to
CAN communication system DTCs are not output. A
CAN communication system DTCs are output (for LHD). B
CAN communication system DTCs are output (for RHD). C



A

5.CHECK FOR DTC AND FREEZE FRAME DATA*

B

C

5.CHECK FOR DTC AND FREEZE FRAME DATA*
a.

Refer to DTC Check / Clear for the blind spot monitor system.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR


b.

Record or print DTCs and freeze frame data, if necessary.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>FREEZE FRAME DATA


Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

6.PROBLEM SYMPTOMS TABLE

B

6.PROBLEM SYMPTOMS TABLE
a.

Refer to Problem Symptoms Table.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table. A
Fault is listed in Problem Symptoms Table. B


HINT:

If the symptom does not recur and no DTCs are output, attempt to reproduce the symptoms.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING




A

7.PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM*

B

ADJUST, REPAIR OR REPLACE IN ACCORPANCE WITH PROBLEM SYMPTOMS TABLE

7.PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM*

NEXT

8.ADJUST, REPAIR OR REPLACE
8.ADJUST, REPAIR OR REPLACE
Result:
Proceed to
NEXT



NEXT

9.PERFORM BEAM AXIS INSPECTION
9.PERFORM BEAM AXIS INSPECTION
a.

Confirm the blind spot monitor beam axis display and perform the blind spot monitor beam axis adjustment.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>OPERATION CHECK


Result:
Proceed to
NEXT



NEXT

10.PERFORM CONFIRMATION TEST*
10.PERFORM CONFIRMATION TEST*
Result:
Proceed to
NEXT



NEXT

END