Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (w/ Telematics Transceiver except G-BOOK) › from 2016.08
RM2660E _56 Audio / Visual / Telematics _052866 TELEMATICS _0283437 TELEMATICS SYSTEM(w/ Telematics Transceiver except G-BOOK) C

TELEMATICS  TELEMATICS SYSTEM(w/ Telematics Transceiver except G-BOOK)  B15C0  Short in GPS Antenna  B15C1  Open in GPS Antenna  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the GPS antenna.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C0 Short in GPS Antenna Current to the telephone antenna assembly is lower than the malfunction threshold for 20 seconds when the engine switch is on (IG).
(Short circuit)
·

Telematics transceiver

·

Telephone antenna assembly

·

No. 4 antenna cord sub-assembly

·

Antenna divider (for 14 Speakers)

·

Harness or connector


B15C1 Open in GPS Antenna Current for telephone antenna assembly is higher than the malfunction threshold for 20 seconds when the engine switch is on (IG).
(Open circuit)
·

Telematics transceiver

·

Telephone antenna assembly

·

No. 4 antenna cord sub-assembly

·

Antenna divider (for 14 Speakers)

·

Harness or connector



WIRING DIAGRAM

except 14 Speakers:
E354524E02
5.448,0.625 5.792,0.823 0.344,0.198 10 false D 5.521,1.573 7,1.844 1.479,0.271 10 false Telematics Transceiver 5.448,1.125 5.792,1.323 0.344,0.198 10 false D 5.427,0.396 5.771,0.594 0.344,0.198 10 false 1 5.406,0.885 5.75,1.083 0.344,0.198 10 false 1a 3.677,1.125 4.021,1.323 0.344,0.198 10 false C 3.677,0.625 4.021,0.823 0.344,0.198 10 false C 3.656,0.385 4,0.583 0.344,0.198 10 false 1 3.615,0.885 3.958,1.083 0.344,0.198 10 false 1a 3.198,0.625 3.542,0.823 0.344,0.198 10 false B 3.208,1.125 3.552,1.323 0.344,0.198 10 false B 3.188,0.385 3.531,0.583 0.344,0.198 10 false 1 3.146,0.875 3.49,1.073 0.344,0.198 10 false 1a 1.708,0.625 2.052,0.823 0.344,0.198 10 false A 1.708,1.125 2.052,1.323 0.344,0.198 10 false A 1.708,0.396 2.052,0.594 0.344,0.198 10 false 2 1.688,0.896 2.031,1.094 0.344,0.198 10 false 2a 1.875,1.51 3.104,1.938 1.229,0.427 10 false No. 4 Antenna Cord Sub-assembly 0.448,1.521 1.677,1.917 1.229,0.396 10 false Telephone Antenna Assembly 5.792,0.615 6.208,0.844 0.417,0.229 10 false ANT2

for 14 Speakers:
E356014E01
1.375,0.635 1.531,0.833 0.156,0.198 10 false A 1.375,1.135 1.531,1.333 0.156,0.198 10 false A 2.656,0.625 2.813,0.823 0.156,0.198 10 false B 2.656,1.135 2.813,1.333 0.156,0.198 10 false B 3.125,0.635 3.281,0.833 0.156,0.198 10 false C 3.135,1.135 3.292,1.333 0.156,0.198 10 false C 5.583,0.625 5.74,0.823 0.156,0.198 10 false D 5.583,1.135 5.74,1.333 0.156,0.198 10 false D 1.385,0.396 1.542,0.594 0.156,0.198 10 false 2 1.354,0.906 1.667,1.104 0.313,0.198 10 false 2a 2.646,0.406 2.802,0.604 0.156,0.198 10 false 1 2.625,0.896 2.938,1.094 0.313,0.198 10 false 1a 3.083,0.906 3.396,1.104 0.313,0.198 10 false 1a 3.125,0.396 3.281,0.594 0.156,0.198 10 false 1 5.573,0.396 5.729,0.594 0.156,0.198 10 false 1 5.542,0.906 5.854,1.104 0.313,0.198 10 false 1a 5.938,0.625 6.552,0.823 0.615,0.198 10 false ANT2 0.188,1.51 1.365,1.917 1.177,0.406 10 false Telephone Antenna Assembly 1.51,1.552 2.729,1.99 1.219,0.438 10 false No. 4 Antenna Cord Sub-assembly 3.948,1.521 5.01,1.802 1.063,0.281 10 false Antenna Divider 5.688,1.615 7.104,1.854 1.417,0.24 10 false Telematics Transceiver

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (w/ Telematics Transceiver except G-BOOK)>REGISTRATION


PROCEDURE

1.CHECK FOR DTC
a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG) and wait for 20 seconds.


d.

Turn the GTS on.


e.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (w/ Telematics Transceiver except G-BOOK)>DTC CHECK / CLEAR

OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK VEHICLE CONDITION
2.CHECK VEHICLE CONDITION
a.

Check the vehicle condition.


Result:
Result Proceed to
except 14 Speakers A
for 14 Speakers B



A

3.INSPECT TELEPHONE ANTENNA ASSEMBLY

B

8.INSPECT TELEPHONE ANTENNA ASSEMBLY
3.INSPECT TELEPHONE ANTENNA ASSEMBLY
a.

Remove the telephone antenna assembly.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


b.
E271865C17
1.979,1.104 2.229,1.104 true 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 2.26,1.01 2.573,1.208 0.313,0.198 10 false 2a
*a Component without harness connected
(Telephone Antenna Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 2a Always 4 to 11 kΩ



Result:
Proceed to
OK
NG



OK

4.INSPECT NO. 4 ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE TELEPHONE ANTENNA ASSEMBLY

4.INSPECT NO. 4 ANTENNA CORD SUB-ASSEMBLY
a.
E354528C01
0.5,0.583 1,0.833 0.5,0.25 0.5,2.5 1,2.75 0.5,0.25 1.333,0.667 1.542,0.667 true 1.906,2.75 2.281,2.75 true 0.083,0.042 0.396,0.24 0.313,0.198 10 false *a 0.135,1.854 0.448,2.052 0.313,0.198 10 false *b 1.146,0.583 1.458,0.781 0.313,0.198 10 false 2a 2.344,2.646 2.656,2.844 0.313,0.198 10 false 1a 0.698,0.625 1.01,0.823 0.313,0.198 10 false A 0.719,2.542 1.031,2.74 0.313,0.198 10 false B
*a Front view of wire harness connector
(to Telephone Antenna Assembly)
*b Front view of wire harness connector
(to Wire Harness)


Disconnect the antenna connector from the telephone antenna assembly.


b.

Disconnect the antenna connector from the wire harness.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-2 - B-1 Always Below 1 Ω
A-2 or B-1 - Body ground Always 10 kΩ or higher
A-2a - B-1a Always Below 1 Ω
A-2a or B-1a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (NO. 4 ANTENNA CORD SUB-ASSEMBLY - TELEMATICS TRANSCEIVER)

NG

REPLACE NO. 4 ANTENNA CORD SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (NO. 4 ANTENNA CORD SUB-ASSEMBLY - TELEMATICS TRANSCEIVER)
a.
E354561C01
0.583,0.667 1.083,0.917 0.5,0.25 0.667,2.5 1.167,2.75 0.5,0.25 1.865,0.958 2.281,0.958 true 1.906,2.74 2.323,2.74 true 1.75,2.667 2.083,1.917 2.083,1.917 2.333,1.917 true 0.031,0.042 0.344,0.24 0.313,0.198 10 false *a 0.063,1.906 0.375,2.104 0.313,0.198 10 false *b 2.375,0.865 2.688,1.063 0.313,0.198 10 false 1a 2.365,2.646 2.677,2.844 0.313,0.198 10 false 1a 0.802,0.708 1.115,0.906 0.313,0.198 10 false C 0.885,2.542 1.198,2.74 0.313,0.198 10 false D 2.406,1.823 2.885,2.073 0.479,0.25 10 false ANT2
*a Front view of wire harness connector
(to No. 4 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Telematics Transceiver)


Disconnect the antenna connector from the No. 4 antenna cord sub-assembly.


b.

Disconnect the antenna connector from the telematics transceiver.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C-1 - D-1 (ANT2) Always Below 1 Ω
C-1 or D-1 (ANT2) - Body ground Always 10 kΩ or higher
C-1a - D-1a Always Below 1 Ω
C-1a or D-1a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.REPLACE TELEPHONE ANTENNA ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE TELEPHONE ANTENNA ASSEMBLY
a.

Replace the telephone antenna assembly with a new or known good one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL



c.

Check for DTCs and check that no DTCs are output.

OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (TELEPHONE ANTENNA ASSEMBLY IS DEFECTIVE)

NG

7.REPLACE TELEMATICS TRANSCEIVER
7.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.INSPECT TELEPHONE ANTENNA ASSEMBLY
a.

Remove the telephone antenna assembly.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL


b.
E271865C17
1.979,1.104 2.229,1.104 true 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 2.26,1.01 2.573,1.208 0.313,0.198 10 false 2a
*a Component without harness connected
(Telephone Antenna Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 2a Always 4 to 11 kΩ



Result:
Proceed to
OK
NG



OK

9.INSPECT NO. 4 ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE TELEPHONE ANTENNA ASSEMBLY

9.INSPECT NO. 4 ANTENNA CORD SUB-ASSEMBLY
a.
E354562C01
0.417,0.583 0.917,0.833 0.5,0.25 0.5,2.531 1,2.781 0.5,0.25 1.302,0.667 1.552,0.667 true 1.917,2.75 2.25,2.75 true 0.073,0.063 0.385,0.26 0.313,0.198 10 false *a 0.083,1.823 0.396,2.021 0.313,0.198 10 false *b 1.115,0.573 1.427,0.771 0.313,0.198 10 false 2a 2.281,2.646 2.594,2.844 0.313,0.198 10 false 1a 0.625,0.615 0.938,0.813 0.313,0.198 10 false A 0.708,2.573 1.021,2.771 0.313,0.198 10 false B
*a Front view of wire harness connector
(to Telephone Antenna Assembly)
*b Front view of wire harness connector
(to Wire Harness)


Disconnect the antenna connector from the telephone antenna assembly.


b.

Disconnect the antenna connector from the wire harness.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-2 - B-1 Always Below 1 Ω
A-2 or B-1 - Body ground Always 10 kΩ or higher
A-2a - B-1a Always Below 1 Ω
A-2a or B-1a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.INSPECT ANTENNA DIVIDER

NG

REPLACE NO. 4 ANTENNA CORD SUB-ASSEMBLY

10.INSPECT ANTENNA DIVIDER
a.
E356011C03
1.542,0.156 1.896,0.417 0.354,0.26 1.542,1.74 1.896,2 0.354,0.26 1.865,1.167 2.49,1.438 true 1.875,2.833 2.5,3.104 true 1.74,2.729 2.25,2.344 2.25,2.344 2.365,2.344 true 0.25,0.365 0.563,0.563 0.313,0.198 10 false *a 0.292,1.969 0.604,2.167 0.313,0.198 10 false *b 1.667,0.208 1.958,0.469 0.292,0.26 10 false C 1.677,1.792 2.083,2.063 0.406,0.271 10 false D 2.521,1.375 2.833,1.573 0.313,0.198 10 false 1a 2.531,3.042 2.844,3.24 0.313,0.198 10 false 1a 2.427,2.271 3.156,2.479 0.729,0.208 10 false ANT2
*a Front view of wire harness connector
(to No. 4 Antenna Cord Sub-assembly)
*a Front view of wire harness connector
(to Telematics Transceiver)


Disconnect the antenna divider connector from the No. 4 antenna cord sub-assmbly.


b.

Disconnect the antenna divider connector from the telematics transceiver.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C-1 - D-1 (ANT2) Always Below 1 Ω
C-1 - D-1a Always 10 kΩ or higher
D-1 (ANT2) - D-1a Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.REPLACE TELEPHONE ANTENNA ASSEMBLY

NG