The multi-media module receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.
This DTC is stored when a microphone connection detection signal line is disconnected.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1579 | Telephone microphone signal is lost. | ·
Multi-media module receiver assembly ·
Map light assembly ·
Telephone microphone assembly ·
DCM (Telematics Transceiver) (w/ Telematics Transceiver) ·
Harness or connector |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION
Choose the model to be inspected.
| Model | Proceed to |
|---|---|
| w/o Telematics Transceiver | A |
| w/ Telematics Transceiver | B |
A
B
Disconnect the F77 multi-media module receiver assembly connector.
Disconnect the R7 map light assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F77-27 (MIN+) - R7-27 (MI1+) | Always | Below 1 Ω |
| F77-29 (MACC) - R7-25 (ACC) | Always | Below 1 Ω |
| F77-48 (MIN-) - R7-26 (MIC-) | Always | Below 1 Ω |
| F77-49 (SNS2) - R7-20 (SNS2) | Always | Below 1 Ω |
| F77-27 (MIN+) - Body ground | Always | 10 kΩ or higher |
| F77-28 (SGND) - Body ground | Always | 10 kΩ or higher |
| F77-29 (MACC) - Body ground | Always | 10 kΩ or higher |
| F77-48 (MIN-) - Body ground | Always | 10 kΩ or higher |
| F77-49 (SNS2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>ROOM LIGHT(for Front)>REMOVAL
Remove the telephone microphone assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE AMPLIFIER>REMOVAL
| *a | Component without harness connected
(Map Light Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-20 (SNS2) - B-1 (SNS2) | Always | Below 1 Ω |
| A-25 (ACC) - B-5 (MACC) | Always | Below 1 Ω |
| A-27 (MI1+) - B-3 (MIC+) | Always | Below 1 Ω |
| A-26 (MIC-) - B-2 (MIC-) | Always | Below 1 Ω |
| A-20 (SNS2) - A-25 (ACC) | Always | 10 kΩ or higher |
| A-20 (SNS2) - A-26 (MIC-) | Always | 10 kΩ or higher |
| A-20 (SNS2) - A-27 (MI1+) | Always | 10 kΩ or higher |
| A-25 (ACC) - A-26 (MIC-) | Always | 10 kΩ or higher |
| A-25 (ACC) - A-27 (MI1+) | Always | 10 kΩ or higher |
| A-26 (MIC-) - A-27 (MI1+) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telephone microphone assembly with a new or normally functioning one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE AMPLIFIER>REMOVAL
Check if the same DTC is output again.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F77 multi-media module receiver assembly connector.
Disconnect the R7 map light assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F77-49 (SNS2) - R7-20 (SNS2) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F77 multi-media module receiver assembly connector.
Disconnect the P3 DCM (telematics transceiver) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F77-27 (MIN+) - P3-18 (MCO+) | Always | Below 1 Ω |
| F77-48 (MIN-) - P3-19 (MCO-) | Always | Below 1 Ω |
| F77-27 (MIN+) - Body ground | Always | 10 kΩ or higher |
| F77-48 (MIN-) - Body ground | Always | 10 kΩ or higher |
| F77-28 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the P3 DCM (telematics transceiver) connector.
Disconnect the R7 map light assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| P3-33 (MCVD) - R7-25 (ACC) | Always | Below 1 Ω |
| P3-34 (MCI+) - R7-27 (MI1+) | Always | Below 1 Ω |
| P3-35 (MCI-) - R7-26 (MIC-) | Always | Below 1 Ω |
| P3-33 (MCVD) - Body ground | Always | 10 kΩ or higher |
| P3-34 (MCI+) - Body ground | Always | 10 kΩ or higher |
| P3-35 (MCI-) - Body ground | Always | 10 kΩ or higher |
| P3-32 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>ROOM LIGHT(for Front)>REMOVAL
Remove the telephone microphone assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE AMPLIFIER>REMOVAL
| *a | Component without harness connected
(Map Light Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-20 (SNS2) - B-1 (SNS2) | Always | Below 1 Ω |
| A-25 (ACC) - B-5 (MACC) | Always | Below 1 Ω |
| A-27 (MI1+) - B-3 (MIC+) | Always | Below 1 Ω |
| A-26 (MIC-) - B-2 (MIC-) | Always | Below 1 Ω |
| A-20 (SNS2) - A-25 (ACC) | Always | 10 kΩ or higher |
| A-20 (SNS2) - A-26 (MIC-) | Always | 10 kΩ or higher |
| A-20 (SNS2) - A-27 (MI1+) | Always | 10 kΩ or higher |
| A-25 (ACC) - A-26 (MIC-) | Always | 10 kΩ or higher |
| A-25 (ACC) - A-27 (MI1+) | Always | 10 kΩ or higher |
| A-26 (MIC-) - A-27 (MI1+) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the R7 map light assembly connector.
| *a | Component with harness connected
(DCM [Telematics Transceiver]) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| P3-33 (MCVD) - Body ground | Engine switch on (ACC) | 4 to 6 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| P3-32 (SGND) - Body ground | Always | Below 1 Ω |
| P3-35 (MCI-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telephone microphone assembly with a new or normally functioning one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE AMPLIFIER>REMOVAL
Check if the same DTC is output again.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG