Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2016.08
RM2660E _56 Audio / Visual / Telematics _052829 NAVIGATION / MULTI INFO DISPLAY _0255494 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Microphone Circuit between Microphone and Radio Receiver  


DESCRIPTION

·

The multi-media module receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

·

Using this circuit, the multi-media module receiver assembly sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the multi-media module receiver assembly (w/o Telematics Transceiver).

·

Using this circuit, the DCM (telematics transceiver) sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the multi-media module receiver assembly via the DCM (telematics transceiver) (w/ Telematics Transceiver).


WIRING DIAGRAM

E356013E02
0.156,0.073 2.156,0.375 2,0.302 12 false w/ Telematics Transceiver: 0.75,0.938 1.365,1.135 0.615,0.198 10 false SNS2 0.708,1.438 1.323,1.635 0.615,0.198 10 false MACC 0.792,1.896 1.406,2.094 0.615,0.198 10 false MIC+ 0.813,2.375 1.427,2.573 0.615,0.198 10 false MIC- 1.531,2.292 2.146,2.49 0.615,0.198 10 false MIC- 1.51,1.792 2.125,1.99 0.615,0.198 10 false MI1+ 1.521,1.323 1.979,1.521 0.458,0.198 10 false ACC 1.469,0.833 2.083,1.031 0.615,0.198 10 false SNS2 1.927,0.844 2.24,1.042 0.313,0.198 10 false 20 1.927,1.333 2.24,1.531 0.313,0.198 10 false 25 1.938,1.813 2.25,2.01 0.313,0.198 10 false 27 1.938,2.292 2.25,2.49 0.313,0.198 10 false 26 1.219,0.844 1.375,1.042 0.156,0.198 10 false 1 1.229,1.344 1.385,1.542 0.156,0.198 10 false 5 1.219,1.823 1.375,2.021 0.156,0.198 10 false 3 1.219,2.302 1.375,2.5 0.156,0.198 10 false 2 2.292,2.969 2.448,3.167 0.156,0.198 10 false * 2.75,2.969 2.906,3.167 0.156,0.198 10 false * 3.156,2.979 3.313,3.177 0.156,0.198 10 false * 5.177,2.458 5.333,2.656 0.156,0.198 10 false * 5.625,2.469 5.781,2.667 0.156,0.198 10 false * 0.292,2.792 1.688,3.281 1.396,0.49 10 false Telephone Microphone Assembly 0.177,3.667 0.49,3.865 0.313,0.198 10 false R7 0.188,3.865 1.51,4.125 1.323,0.26 10 false Map Light Assembly 3.615,3.625 3.927,3.823 0.313,0.198 10 false P3 3.615,3.802 4.677,4.219 1.063,0.417 10 false DCM (Telematics Transceiver) 5.885,3.688 6.344,3.885 0.458,0.198 10 false F77 5.885,3.865 7.083,4.354 1.198,0.49 10 false Multi-media Module Receiver Assembly 3.396,1.344 3.708,1.542 0.313,0.198 10 false 33 3.396,1.813 3.708,2.01 0.313,0.198 10 false 34 3.385,2.281 3.698,2.479 0.313,0.198 10 false 35 3.385,2.719 3.698,2.917 0.313,0.198 10 false 32 3.635,1.448 4.25,1.646 0.615,0.198 10 false MCVD 3.635,1.906 4.25,2.104 0.615,0.198 10 false MCI+ 3.646,2.396 4.26,2.594 0.615,0.198 10 false MCI- 3.635,2.844 4.25,3.042 0.615,0.198 10 false SGND 4.323,1.417 4.938,1.615 0.615,0.198 10 false MCO+ 4.344,1.885 4.958,2.083 0.615,0.198 10 false MCO- 5.854,0.833 6.167,1.031 0.313,0.198 10 false 49 5.865,1.344 6.177,1.542 0.313,0.198 10 false 27 5.865,1.813 6.177,2.01 0.313,0.198 10 false 48 5.865,2.229 6.177,2.427 0.313,0.198 10 false 28 4.813,1.344 5.125,1.542 0.313,0.198 10 false 18 4.823,1.823 5.135,2.021 0.313,0.198 10 false 19 6.104,0.938 6.719,1.135 0.615,0.198 10 false SNS2 6.104,1.427 6.719,1.625 0.615,0.198 10 false MIN+ 6.104,6.729 6.719,6.927 0.615,0.198 10 false MIN- 6.094,2.333 6.708,2.531 0.615,0.198 10 false SGND 5.906,8.167 7.104,8.656 1.198,0.49 10 false Multi-media Module Receiver Assembly 5.906,8 6.365,8.198 0.458,0.198 10 false F77 0.208,8.021 0.521,8.219 0.313,0.198 10 false R7 0.208,8.198 1.531,8.458 1.323,0.26 10 false Map Light Assembly 0.281,7.104 1.677,7.594 1.396,0.49 10 false Telephone Microphone Assembly 1.448,5.167 2.063,5.365 0.615,0.198 10 false SNS2 6.104,5.271 6.719,5.469 0.615,0.198 10 false SNS2 1.51,5.667 2.125,5.865 0.615,0.198 10 false MI1+ 1.531,6.156 1.99,6.354 0.458,0.198 10 false ACC 1.531,6.625 2.146,6.823 0.615,0.198 10 false MIC- 0.74,5.26 1.354,5.458 0.615,0.198 10 false SNS2 0.708,6.24 1.323,6.438 0.615,0.198 10 false MACC 0.771,5.771 1.385,5.969 0.615,0.198 10 false MIC+ 0.813,6.698 1.427,6.896 0.615,0.198 10 false MIC- 6.115,5.771 6.729,5.969 0.615,0.198 10 false MIN+ 6.104,1.917 6.719,2.115 0.615,0.198 10 false MIN- 6.104,6.25 6.719,6.448 0.615,0.198 10 false MACC 6.094,7.198 6.708,7.396 0.615,0.198 10 false SGND 4.896,7.344 5.052,7.542 0.156,0.198 10 false * 3.833,7.375 3.99,7.573 0.156,0.198 10 false * 5.823,7.083 6.135,7.281 0.313,0.198 10 false 28 5.813,6.625 6.125,6.823 0.313,0.198 10 false 48 5.802,6.135 6.115,6.333 0.313,0.198 10 false 29 5.792,5.677 6.104,5.875 0.313,0.198 10 false 27 5.792,5.177 6.104,5.375 0.313,0.198 10 false 49 1.948,5.177 2.26,5.375 0.313,0.198 10 false 20 1.948,5.688 2.26,5.885 0.313,0.198 10 false 27 1.938,6.156 2.25,6.354 0.313,0.198 10 false 25 1.938,6.635 2.25,6.833 0.313,0.198 10 false 26 1.208,5.177 1.365,5.375 0.156,0.198 10 false 1 1.229,6.156 1.385,6.354 0.156,0.198 10 false 5 1.219,5.677 1.375,5.875 0.156,0.198 10 false 3 1.24,6.625 1.396,6.823 0.156,0.198 10 false 2 0.135,4.427 2.26,4.729 2.125,0.302 12 false w/o Telematics Transceiver:

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION


PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.

Model:
Model Proceed to
w/o Telematics Transceiver A
w/ Telematics Transceiver B




A

2.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)

B

5.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the F77 multi-media module receiver assembly connector.


b.

Disconnect the R7 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-27 (MIN+) - R7-27 (MI1+) Always Below 1 Ω
F77-29 (MACC) - R7-25 (ACC) Always Below 1 Ω
F77-48 (MIN-) - R7-26 (MIC-) Always Below 1 Ω
F77-49 (SNS2) - R7-20 (SNS2) Always Below 1 Ω
F77-27 (MIN+) - Body ground Always 10 kΩ or higher
F77-28 (SGND) - Body ground Always 10 kΩ or higher
F77-29 (MACC) - Body ground Always 10 kΩ or higher
F77-48 (MIN-) - Body ground Always 10 kΩ or higher
F77-49 (SNS2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>ROOM LIGHT(for Front)>REMOVAL


b.

Remove the telephone microphone assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE AMPLIFIER>REMOVAL


c.
E356115C03
1.531,1.813 1.938,2.073 0.406,0.26 1.521,0.104 1.927,0.365 0.406,0.26 0.917,3.052 1.188,2.688 true 1.313,3.042 1.469,2.677 true 1.667,3.042 1.719,2.698 true 2.292,3.031 2.219,2.698 true 2.552,1.469 2.406,1.083 true 1.198,1.479 1.406,1.083 true 1.969,1.458 1.698,1.073 true 1.583,1.469 1.563,1.083 true 0.156,0.135 0.385,0.313 0.229,0.177 10 false *a 0.677,3.083 1.073,3.26 0.396,0.177 10 false SNS2 1.167,3.083 1.563,3.26 0.396,0.177 10 false MIC- 1.542,3.083 1.938,3.26 0.396,0.177 10 false MIC+ 2.135,3.083 2.531,3.26 0.396,0.177 10 false MACC 2.469,1.5 2.865,1.677 0.396,0.177 10 false SNS2 1,1.479 1.354,1.646 0.354,0.167 10 false MI1+ 1.938,1.479 2.292,1.646 0.354,0.167 10 false ACC 1.479,1.479 1.833,1.646 0.354,0.167 10 false MIC- 1.688,0.146 1.844,0.344 0.156,0.198 10 false A 1.698,1.865 1.854,2.063 0.156,0.198 10 false B
*a Component without harness connected
(Map Light Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-20 (SNS2) - B-1 (SNS2) Always Below 1 Ω
A-25 (ACC) - B-5 (MACC) Always Below 1 Ω
A-27 (MI1+) - B-3 (MIC+) Always Below 1 Ω
A-26 (MIC-) - B-2 (MIC-) Always Below 1 Ω
A-20 (SNS2) - A-25 (ACC) Always 10 kΩ or higher
A-20 (SNS2) - A-26 (MIC-) Always 10 kΩ or higher
A-20 (SNS2) - A-27 (MI1+) Always 10 kΩ or higher
A-25 (ACC) - A-26 (MIC-) Always 10 kΩ or higher
A-25 (ACC) - A-27 (MI1+) Always 10 kΩ or higher
A-26 (MIC-) - A-27 (MI1+) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK TELEPHONE MICROPHONE ASSEMBLY

NG

4.CHECK TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a new or normally functioning one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE AMPLIFIER>REMOVAL


b.

Check if the same malfunction recurs.

OK:

Malfunction does not recur (returns to normal).



Result:
Proceed to
OK
NG



OK

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the F77 multi-media module receiver assembly connector.


b.

Disconnect the R7 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-49 (SNS2) - R7-20 (SNS2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - DCM [TELEMATICS TRANSCEIVER])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - DCM [TELEMATICS TRANSCEIVER])
a.

Disconnect the F77 multi-media module receiver assembly connector.


b.

Disconnect the P3 DCM (telematics transceiver) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-27 (MIN+) - P3-18 (MCO+) Always Below 1 Ω
F77-48 (MIN-) - P3-19 (MCO-) Always Below 1 Ω
F77-27 (MIN+) - Body ground Always 10 kΩ or higher
F77-48 (MIN-) - Body ground Always 10 kΩ or higher
F77-28 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (DCM [TELEMATICS TRANSCEIVER] - MAP LIGHT ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (DCM [TELEMATICS TRANSCEIVER] - MAP LIGHT ASSEMBLY)
a.

Disconnect the P3 DCM (telematics transceiver) connector.


b.

Disconnect the R7 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P3-33 (MCVD) - R7-25 (ACC) Always Below 1 Ω
P3-34 (MCI+) - R7-27 (MI1+) Always Below 1 Ω
P3-35 (MCI-) - R7-26 (MIC-) Always Below 1 Ω
P3-33 (MCVD) - Body ground Always 10 kΩ or higher
P3-34 (MCI+) - Body ground Always 10 kΩ or higher
P3-35 (MCI-) - Body ground Always 10 kΩ or higher
P3-32 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>ROOM LIGHT(for Front)>REMOVAL


b.

Remove the telephone microphone assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE AMPLIFIER>REMOVAL


c.
E356115C03
1.531,1.813 1.938,2.073 0.406,0.26 1.521,0.104 1.927,0.365 0.406,0.26 0.917,3.052 1.188,2.688 true 1.313,3.042 1.469,2.677 true 1.667,3.042 1.719,2.698 true 2.292,3.031 2.219,2.698 true 2.552,1.469 2.406,1.083 true 1.198,1.479 1.406,1.083 true 1.969,1.458 1.698,1.073 true 1.583,1.469 1.563,1.083 true 0.156,0.135 0.385,0.313 0.229,0.177 10 false *a 0.677,3.083 1.073,3.26 0.396,0.177 10 false SNS2 1.167,3.083 1.563,3.26 0.396,0.177 10 false MIC- 1.542,3.083 1.938,3.26 0.396,0.177 10 false MIC+ 2.135,3.083 2.531,3.26 0.396,0.177 10 false MACC 2.469,1.5 2.865,1.677 0.396,0.177 10 false SNS2 1,1.479 1.354,1.646 0.354,0.167 10 false MI1+ 1.938,1.479 2.292,1.646 0.354,0.167 10 false ACC 1.479,1.479 1.833,1.646 0.354,0.167 10 false MIC- 1.688,0.146 1.844,0.344 0.156,0.198 10 false A 1.698,1.865 1.854,2.063 0.156,0.198 10 false B
*a Component without harness connected
(Map Light Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-20 (SNS2) - B-1 (SNS2) Always Below 1 Ω
A-25 (ACC) - B-5 (MACC) Always Below 1 Ω
A-27 (MI1+) - B-3 (MIC+) Always Below 1 Ω
A-26 (MIC-) - B-2 (MIC-) Always Below 1 Ω
A-20 (SNS2) - A-25 (ACC) Always 10 kΩ or higher
A-20 (SNS2) - A-26 (MIC-) Always 10 kΩ or higher
A-20 (SNS2) - A-27 (MI1+) Always 10 kΩ or higher
A-25 (ACC) - A-26 (MIC-) Always 10 kΩ or higher
A-25 (ACC) - A-27 (MI1+) Always 10 kΩ or higher
A-26 (MIC-) - A-27 (MI1+) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK DCM (TELEMATICS TRANSCEIVER)

NG

9.CHECK DCM (TELEMATICS TRANSCEIVER)
a.

Disconnect the R7 map light assembly connector.


b.
E283057C25
1.625,0.646 2.021,0.854 0.396,0.208 0.729,2.677 1.24,2.073 true 1.365,2.865 1.49,2.063 true 2.406,2.938 1.583,2.083 true 0.24,0.135 0.552,0.292 0.313,0.156 10 false *a 0.563,2.719 0.958,2.875 0.396,0.156 10 false MCI- 1.146,2.896 1.646,3.073 0.5,0.177 10 false MCVD 2.26,2.979 2.76,3.156 0.5,0.177 10 false SGND 1.729,0.667 2.052,0.844 0.323,0.177 10 false P3
*a Component with harness connected
(DCM [Telematics Transceiver])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
P3-33 (MCVD) - Body ground Engine switch on (ACC) 4 to 6 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P3-32 (SGND) - Body ground Always Below 1 Ω
P3-35 (MCI-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.CHECK TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE DCM (TELEMATICS TRANSCEIVER)

10.CHECK TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a new or normally functioning one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE AMPLIFIER>REMOVAL


b.

Check if the same malfunction recurs.

OK:

Malfunction does not recur (returns to normal).



Result:
Proceed to
OK
NG



OK

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY