Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › 2016.08–2019.08
RM2660E _53 Suspension _052817 TIRE PRESSURE MONITORING _0255402 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  C2195/95  Multi-receiver Antenna Circuit (Test Mode DTC)  


DESCRIPTION

This DTC is used for detecting open circuits and radio wave frequency mismatches in the tire pressure warning antenna.

DTC No. DTC Detection Condition Trouble Area
C2195/95 Test mode procedure is performed.
·

Tire pressure warning antenna

·

Harness or connector

·

Tire pressure warning ECU and receiver



WIRING DIAGRAM

C345740E02
4.591,1.862 6.049,2.259 1.457,0.397 10 Tire Pressure Warning ECU and Receiver 1.155,1.862 2.881,2.217 1.725,0.355 10 Tire Pressure Warning Antenna 2.411,0.972 2.651,1.183 0.239,0.211 10 1 4.94,1.23 5.416,1.400 0.475,0.170 10 TPMS 1.878,1.23 2.353,1.400 0.475,0.170 10 TPMS 4.679,0.972 4.825,1.146 0.147,0.174 10 1 4.591,1.713 4.955,1.903 0.363,0.190 10 L85 1.155,1.713 1.473,1.873 0.318,0.161 10 A77 3.322,1.502 3.908,1.665 0.586,0.163 10 Shielded

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initialization (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER - TIRE PRESSURE WARNING ANTENNA)
a.

Disconnect the L85 tire pressure warning ECU and receiver connector.


b.

Disconnect the A77 tire pressure warning antenna connector.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

Because the coaxial cable that is used for the tire pressure warning antenna consists of a center conductor and an outer shielding layer (-), this measurement should be performed to ensure that there is no malfunction in the coaxial cable.


Standard Resistance:
Tester Connection Condition Specified Condition
L85-1 (TPMS) - A77-1 (TPMS) Always Below 1 Ω
L85-1 (shielded wire) - A77-1 (shielded wire) Always Below 1 Ω
L85-1 (TPMS) - A77-1 (shielded wire) Always 10 kΩ or higher
L85-1 (shielded wire) - A77-1 (TPMS) Always 10 kΩ or higher




OK

2.CHECK TIRE PRESSURE WARNING ANTENNA RECEPTION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK TIRE PRESSURE WARNING ANTENNA RECEPTION
a.

Set the tire pressure to the specified value (See page Suspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION).


b.

Turn the ignition switch off.


c.

Connect the L85 tire pressure warning ECU and receiver connector.


d.

Connect the A77 tire pressure warning antenna connector.

NOTICE:

Be sure to disconnect the connector on the tire pressure warning antenna.



e.

Connect the GTS to the DLC3.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


i.

Check the values by referring to the table below.

Tire Pressure Monitor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
ID 1 Tire Inflation Pressure ID1 tire inflation pressure/
min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 2 Tire Inflation Pressure ID2 tire inflation pressure/
min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 3 Tire Inflation Pressure ID3 tire inflation pressure/
min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 4 Tire Inflation Pressure ID4 tire inflation pressure/
min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 5 Tire Inflation Pressure ID5 tire inflation pressure/
min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*

HINT:
·

*: It may take a few minutes until the values are displayed.

·

The wheel position cannot be determined from ID1 through ID5 on the Data List.




j.

Rapidly reduce the tire pressure for each wheel at least 40 kPa (0.4 kgf/cm2, 5.8 psi) within 30 seconds.

i.

Check that each tire pressure value displayed on the GTS has changed.

Result:
Result Proceed to
Tire pressure data does not change A
Tire pressure of at least 1 wheel changes B





A

3.REPLACE TIRE PRESSURE WARNING ANTENNA

B

4.CHECK TEST MODE DTC (C2195/95)
3.REPLACE TIRE PRESSURE WARNING ANTENNA
a.

Replace the tire pressure warning antenna (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING ANTENNA>REMOVAL).



NEXT

4.CHECK TEST MODE DTC (C2195/95)
4.CHECK TEST MODE DTC (C2195/95)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Tire Pressure Monitor / Utility / Signal Check.


f.

Perform the test mode inspection (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>PROBLEM SYMPTOMS TABLE).

Result:
Result Proceed to
DTC C2195/95 is not cleared A
DTC 2195/95 is cleared (When performing the test mode inspection after replacing the tire pressure warning antenna (for Rear Side) or tire pressure warning antenna) B
DTC 2195/95 is cleared (When performing the test mode inspection after the tire pressures have changed as a result of the tire pressure warning antenna reception check) C




A

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

B

END

C