Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU) › from 2016.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255536 CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)  Check Bus 3 Lines for Short Circuit  


DESCRIPTION

There may be a short circuit between the bus 3 CAN main wires and/or CAN branch wires when the resistance between terminals 6 (CA3H) and 21 (CA3L) of the central gateway ECU is below 54 Ω.

Detection Item Trouble Area
Resistance between terminals 6 (CA3H) and 21 (CA3L) of central gateway ECU is below 54 Ω.
·

Short in bus 3 CAN main wires

·

Short in bus 3 CAN branch wires

·

Central gateway ECU

·

Multi-media module receiver assembly*1

·

Bus buffer ECU*2

·

Radio and display receiver assembly*3

·

Telematics transceiver*4

·

No. 5 CAN junction connector

·

No. 6 CAN junction connector

·

No. 2 CAN junction terminal



*1: for Multi-media Module Receiver Type

*2: w/ Bus Buffer ECU

*3: for Radio and Display Type

*4: w/ Telematics Transceiver


WIRING DIAGRAM

C348152E01
5.635,1.417 7.115,1.594 1.479,0.177 10 false E145 5.646,1.594 7.125,1.771 1.479,0.177 10 false Central Gateway ECU 5.76,0.281 6.042,0.49 0.281,0.208 10 false 6 5.667,0.844 5.948,1.052 0.281,0.208 10 false 21 6,0.333 6.573,0.51 0.573,0.177 10 false CA3H 6.01,1.094 6.583,1.271 0.573,0.177 10 false CA3L 4.146,0.333 4.448,0.51 0.302,0.177 10 false 8 4.125,0.854 4.406,1.01 0.281,0.156 10 false 19 3.188,0.302 3.49,0.479 0.302,0.177 10 false 9 3.104,0.854 3.385,1.01 0.281,0.156 10 false 20 1.427,0.313 1.729,0.49 0.302,0.177 10 false 2 1.417,0.844 1.719,1.021 0.302,0.177 10 false 1 0.875,0.438 1.448,0.615 0.573,0.177 10 false CAN+ 0.875,0.969 1.448,1.146 0.573,0.177 10 false CAN- 0.115,1.417 1.594,1.594 1.479,0.177 10 false E173 0.115,1.583 1.594,1.76 1.479,0.177 10 false Bus Buffer ECU*1 3.104,2.365 3.385,2.521 0.281,0.156 10 false 10 3.094,2.896 3.375,3.052 0.281,0.156 10 false 21 4.125,2.354 4.406,2.51 0.281,0.156 10 false 11 4.135,2.885 4.417,3.042 0.281,0.156 10 false 22 2.927,3.229 4.406,3.406 1.479,0.177 10 false E152 2.927,3.427 4.156,3.802 1.229,0.375 10 false No. 5 CAN Junction Connector 1.438,2.344 1.74,2.521 0.302,0.177 10 false 1 1.448,2.885 1.75,3.063 0.302,0.177 10 false 2 0.833,2.479 1.406,2.656 0.573,0.177 10 false CANH 0.844,3.021 1.417,3.198 0.573,0.177 10 false CANL 0.083,3.208 1.563,3.385 1.479,0.177 10 false F77 0.073,3.427 1.875,3.771 1.802,0.344 10 false Multi-media Module Receiver Assembly*2 1.438,4.458 1.74,4.635 0.302,0.177 10 false 9 1.427,5 1.708,5.156 0.281,0.156 10 false 10 0.844,4.594 1.417,4.771 0.573,0.177 10 false CANH 0.865,5.125 1.438,5.302 0.573,0.177 10 false CANL 0.031,5.51 1.76,5.865 1.729,0.354 10 false Radio and Display Receiver Assembly*3 0.052,5.323 1.531,5.5 1.479,0.177 10 false F124 4.156,4.438 4.458,4.615 0.302,0.177 10 false 6 4.135,5 4.417,5.156 0.281,0.156 10 false 17 4.167,7.167 4.469,7.344 0.302,0.177 10 false 7 4.125,7.708 4.406,7.865 0.281,0.156 10 false 18 5.75,7.698 6.052,7.875 0.302,0.177 10 false 2 5.76,7.156 6.063,7.333 0.302,0.177 10 false 3 5.99,7.156 6.563,7.333 0.573,0.177 10 false CANH 6.021,7.969 6.594,8.146 0.573,0.177 10 false CANL 5.313,8.26 7.156,8.458 1.844,0.198 10 false No. 2 CAN Junction Terminal 5.313,8.073 7.156,8.271 1.844,0.198 10 false F98 2.719,8.229 4.708,8.448 1.99,0.219 10 false No. 6 CAN Junction Connector 2.719,8.083 4.708,8.302 1.99,0.219 10 false F99 3.156,7.156 3.458,7.333 0.302,0.177 10 false 5 3.125,7.698 3.406,7.854 0.281,0.156 10 false 16 1.396,7.188 1.677,7.344 0.281,0.156 10 false 15 1.396,7.698 1.677,7.854 0.281,0.156 10 false 16 0.875,7.302 1.448,7.479 0.573,0.177 10 false CANP 0.885,7.854 1.458,8.031 0.573,0.177 10 false CANN 0.052,8.26 1.896,8.458 1.844,0.198 10 false Telematics Transceiver*4 0.052,8.094 1.896,8.292 1.844,0.198 10 false P3 4.896,2.625 7.021,2.833 2.125,0.208 10 false *1: w/ Bus Buffer ECU 4.927,3.771 7,4.042 2.073,0.271 10 false *3: for Radio and Display Type 4.906,3.115 6.563,3.531 1.656,0.417 10 false *2: for Multi-media Module Receiver Type 4.938,4.167 7.01,4.438 2.073,0.271 10 false *4: w/ Telematics Transceiver

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR SHORT IN CAN BUS WIRES (CENTRAL GATEWAY ECU - NO. 5 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
U165598E01
0.071,0.041 0.241,0.194 0.170,0.153 10 *a 1.505,0.138 1.852,0.277 0.347,0.139 10 E145 2.814,0.252 3.230,0.403 0.416,0.151 10 CA3H 2.655,1.737 3.127,1.889 0.472,0.151 10 CA3L 2.308,0.905 2.675,0.355 2.675,0.355 2.789,0.355 false 2.637,1.821 2.448,1.821 2.448,1.821 2.196,1.197 false

Disconnect the central gateway ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E145-6 (CA3H) - E145-21 (CA3L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Central Gateway ECU)



OK

NG

2.CONNECT CONNECTOR
2.CONNECT CONNECTOR
a.

Reconnect the E145 central gateway ECU connector.



NEXT

3.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION TERMINAL - NO. 6 CAN JUNCTION CONNECTOR)
3.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION TERMINAL - NO. 6 CAN JUNCTION CONNECTOR)
a.
U165511E02
1.344,0.698 1.146,0.406 1.146,0.406 1.021,0.406 false 1.292,0.146 1.563,0.146 1.563,0.146 1.667,0.708 false 0.125,0.063 0.5,0.271 0.375,0.208 10 false *a 0.406,0.833 0.823,1.052 0.417,0.219 10 false F98 0.573,0.323 1.135,0.521 0.563,0.198 10 false CANH 0.854,0.073 1.396,0.26 0.542,0.188 10 false CANL

Disconnect the No. 2 CAN junction terminal connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F98-3 (CANH) - F98-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 CAN Junction Terminal)



OK

REPLACE NO. 2 CAN JUNCTION TERMINAL

NG

4.CONNECT CONNECTOR
4.CONNECT CONNECTOR
a.

Reconnect the F98 No. 2 CAN junction terminal connector.



NEXT

5.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 CAN JUNCTION CONNECTOR)
5.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 5 CAN junction connector.

U165242E01
0.096,0.095 0.391,0.320 0.295,0.225 10 *a 2.285,0.509 2.969,0.660 0.684,0.151 10 CANH*b 2.309,2.485 2.993,2.631 0.684,0.146 10 CANL*b 2.127,1.184 2.811,1.335 0.684,0.151 10 CANH*e 2.221,0.727 2.904,0.879 0.684,0.151 10 CANH*c 2.089,0.939 2.772,1.090 0.684,0.151 10 CANH*d 2.152,1.785 2.835,1.932 0.684,0.146 10 CANL*e 2.152,2.02 2.835,2.167 0.684,0.146 10 CANL*d 2.25,2.262 2.934,2.408 0.684,0.146 10 CANL*c 3.443,0.231 3.793,0.373 0.350,0.142 10 E152 3.023,1.664 2.828,1.849 2.828,1.849 2.714,1.849 false 2.859,2.556 3.035,2.556 3.035,2.556 3.375,1.664 false 3.023,1.454 2.828,1.27 2.828,1.27 2.714,1.27 false 2.869,0.592 3.045,0.592 3.045,0.592 3.375,1.454 false 2.673,1.018 2.831,1.018 2.831,1.018 3.153,1.462 false 2.673,2.105 2.831,2.105 2.831,2.105 3.153,1.661 false

Text in Illustration
*a Rear view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to Central Gateway ECU
*c to Bus Buffer ECU (w/ Bus Buffer ECU) *d
·

to Multi-media Module Receiver Assembly (for Multi-media Module Receiver Type)

·

to Radio and Display Receiver Assembly (for Radio and Display Type)


*e to No. 6 CAN Junction Connector - -


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
E152-8 (CANH) - E152-19 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU
E152-9 (CANH) - E152-20 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Bus buffer ECU*1
E152-10 (CANH) - E152-21 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher
·

Multi-media module receiver assembly*2

·

Radio and display receiver assembly*3


E152-11 (CANH) - E152-22 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 6 CAN junction connector


*1: w/ Bus Buffer ECU

*2: for Multi-media Module Receiver Type

*3: Radio and Display Type


Result
Result Proceed to
OK A
NG (Central gateway ECU CAN main wire) B
NG (No. 6 CAN junction connector CAN main wire) C
NG (ECU or sensor CAN branch wires) D



A

REPLACE NO. 5 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU)

C

6.CONNECT CONNECTOR

D

8.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
6.CONNECT CONNECTOR
a.

Reconnect the E152 No. 5 CAN junction connector.



NEXT

7.CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 CAN JUNCTION CONNECTOR)
7.CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 6 CAN junction connector.

U165243E02
3.469,1.667 2.99,2.01 2.99,2.01 2.875,2.01 false 2.896,2.313 3.073,2.313 3.073,2.313 3.594,1.667 false 3.469,1.458 2.896,1.125 2.896,1.125 2.781,1.125 false 2.792,0.823 2.969,0.823 2.969,0.823 3.594,1.458 false 2.885,0.542 3.063,0.542 3.063,0.542 3.667,1.458 false 3.021,2.563 3.198,2.563 3.198,2.563 3.677,1.646 false 0.094,0.094 0.385,0.323 0.292,0.229 10 false *a 2.24,0.729 2.927,0.875 0.688,0.146 10 false CANH*c 2.375,2.188 3.063,2.333 0.688,0.146 10 false CANL*c 2.458,2.479 3.146,2.625 0.688,0.146 10 false CANL*b 2.292,0.448 2.979,0.594 0.688,0.146 10 false CANH*b 3.479,0.229 3.74,0.375 0.26,0.146 10 false F99 2.219,1.021 2.906,1.167 0.688,0.146 10 false CANH*d 2.313,1.927 3,2.073 0.688,0.146 10 false CANL*d

Text in Illustration
*a Rear view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to Telematics Transceiver (w/ Telematics Transceiver)
*c to No. 5 CAN Junction Connector *d to No. 2 CAN Junction Terminal


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to

*: w/ Telematics Transceiver

F99-5 (CANH) - F99-16 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Telematics transceiver*
F99-6 (CANH) - F99-17 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 5 CAN junction connector
F99-7 (CANH) - F99-18 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 2 CAN junction terminal


Result
Result Proceed to
OK A
NG (No. 5 CAN junction connector CAN main wire) B
NG (No. 2 CAN junction terminal CAN main wire) C
NG (ECU or sensor CAN branch wires) D



A

REPLACE NO. 6 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 6 CAN JUNCTION CONNECTOR - NO. 5 CAN JUNCTION CONNECTOR)

C

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 6 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION TERMINAL)

D

8.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
8.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
a.
U165590E02
1.385,0.979 0.885,0.427 0.885,0.427 0.76,0.427 false 1.417,1.104 1.031,1.771 1.031,1.771 0.906,1.771 false 1.563,0.302 2.073,0.542 0.51,0.24 10 false E145 0.104,0.073 0.438,0.281 0.333,0.208 10 false *a 0.333,0.344 1,0.563 0.667,0.219 10 false CA3H 0.479,1.688 1.146,1.906 0.667,0.219 10 false CA3L

Reconnect the CAN junction connector.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited CAN branch wire is connected.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E145-6 (CA3H) - E145-21 (CA3L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Text in Illustration
*a Component with harness connected
(Central Gateway ECU)

HINT:

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.




OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR CAN BRANCH WIRES OR CONNECTOR