Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (w/ Multi-display) › from 2016.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255488 AUDIO AND VISUAL SYSTEM(w/ Multi-display) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(w/ Multi-display)  Mute Signal Circuit between Stereo Component Amplifier and Telematics Transceiver  


DESCRIPTION

This DCM (telematics transceiver) sends a mute signal to the stereo component amplifier assembly. The stereo component amplifier assembly controls the volume according to the mute signal from the DCM (telematics transceiver).

If there is an open in the circuit, noise can be heard from the speakers when changing the sound source.

If there is a short in the circuit, even though the stereo component amplifier assembly is functioning normally, no sound or only an extremely faint sound can be heard.

WIRING DIAGRAM

E246907E37
4.813,0.844 5.104,1.063 0.292,0.219 10 false 17 5.052,0.958 5.51,1.156 0.458,0.198 10 false MUTE 1.229,1.99 2.479,2.354 1.25,0.365 10 false Stereo Component Amplifier Assembly 4.885,1.823 5.344,2.021 0.458,0.198 10 false P3 4.885,1.99 6.854,2.24 1.969,0.25 10 false DCM (Telematics Transceiver) 2.188,0.854 2.438,1.073 0.25,0.219 10 false 2 1.729,0.958 2.188,1.156 0.458,0.198 10 false TMUT 1.219,1.813 1.677,2.01 0.458,0.198 10 false F74

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION


PROCEDURE

1.INSPECT DCM (TELEMATICS TRANSCEIVER)
a.
E283621C07
0.198,0.865 0.688,1.125 0.49,0.26 1.042,0.354 1.292,0.354 1.292,0.354 1.458,1.188 true 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 0.323,0.906 0.719,1.104 0.396,0.198 10 false P3 0.615,0.271 1.177,0.469 0.563,0.198 10 false MUTE
*a Component with harness connected
(DCM [Telematics Transceiver])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
P3-17 (MUTE) - Body ground Engine switch on (ACC)
Audio system playing
→ Emergency call mode
3.5 V or higher → Below 1 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - DCM [TELEMATICS TRANSCEIVER])
2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - DCM [TELEMATICS TRANSCEIVER])
a.

Disconnect the F74 stereo component amplifier assembly connector.


b.

Disconnect the P3 DCM (telematics transceiver) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F74-2 (TMUT) - P3-17 (MUTE) Always Below 1 Ω
F74-2 (TMUT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY
a.
E176650C40
1.479,0.719 1.969,1.01 0.49,0.292 1.99,2.083 2.167,2.583 false 0.188,0.167 0.354,0.323 0.167,0.156 10 false *a 2.031,2.635 2.458,2.792 0.427,0.156 10 false MUTE 1.604,0.771 1.948,0.969 0.344,0.198 10 false P3
*a Front view of wire harness connector
(to DCM [Telematics Transceiver])


Reconnect the stereo component amplifier assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
P3-17 (MUTE) - Body ground Engine switch on (ACC) 3.5 V or higher



Result:
Proceed to
OK
NG



OK

REPLACE DCM (TELEMATICS TRANSCEIVER)

NG

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY