Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (w/ Multi-display) › from 2016.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255488 AUDIO AND VISUAL SYSTEM(w/ Multi-display) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(w/ Multi-display)  B1579  Voice Recognition Microphone Disconnected  


DESCRIPTION

The multi-media module receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

This DTC is stored when a microphone connection detection signal line is disconnected.

DTC Code DTC Detection Condition Trouble Area
B1579 Telephone microphone signal is lost.
·

Multi-media module receiver assembly

·

Map light assembly

·

Telephone microphone assembly

·

DCM (Telematics Transceiver) (w/ Telematics Transceiver)

·

Harness or connector



WIRING DIAGRAM

E356114E02
0.156,0.094 2.167,0.302 2.01,0.208 12 false w/ Telematics Transceiver: 0.167,4.51 2.323,4.75 2.156,0.24 12 false w/o Telematics Transceiver: 2.302,2.979 2.458,3.125 0.156,0.146 10 false * 2.729,2.979 2.885,3.125 0.156,0.146 10 false * 3.135,2.99 3.292,3.135 0.156,0.146 10 false * 5.177,2.479 5.333,2.625 0.156,0.146 10 false * 5.604,2.49 5.76,2.635 0.156,0.146 10 false * 0.25,2.865 1.667,3.229 1.417,0.365 10 false Telephone Microphone Assembly 0.177,3.667 0.427,3.875 0.25,0.208 10 false R7 0.188,3.823 1.531,4.042 1.344,0.219 10 false Map Light Assembly 3.635,3.677 3.885,3.885 0.25,0.208 10 false P3 3.625,3.844 4.708,4.229 1.083,0.385 10 false DCM (Telematics Transceiver) 5.844,3.667 6.094,3.875 0.25,0.208 10 false F77 5.844,3.833 7.073,4.208 1.229,0.375 10 false Multi-media Module Receiver Assembly 6.115,0.927 6.542,1.125 0.427,0.198 10 false SNS2 6.125,1.427 6.552,1.625 0.427,0.198 10 false MIN+ 6.125,1.917 6.552,2.115 0.427,0.198 10 false MIN- 6.125,2.344 6.552,2.542 0.427,0.198 10 false SGND 5.865,0.823 6.083,1.01 0.219,0.188 10 false 49 5.865,1.323 6.083,1.51 0.219,0.188 10 false 27 5.865,1.802 6.083,1.99 0.219,0.188 10 false 48 5.865,2.219 6.083,2.406 0.219,0.188 10 false 28 4.323,1.427 4.75,1.625 0.427,0.198 10 false MCO+ 4.813,1.344 5.031,1.531 0.219,0.188 10 false 18 4.333,1.896 4.76,2.094 0.427,0.198 10 false MCO- 4.833,1.802 5.052,1.99 0.219,0.188 10 false 19 3.635,1.427 4.063,1.625 0.427,0.198 10 false MCVD 3.635,1.906 4.063,2.104 0.427,0.198 10 false MCI+ 3.646,2.375 4.073,2.542 0.427,0.167 10 false MCI- 3.646,2.844 4.073,3.042 0.427,0.198 10 false SGND 3.385,1.333 3.604,1.521 0.219,0.188 10 false 33 3.396,1.813 3.615,2 0.219,0.188 10 false 34 3.396,2.281 3.615,2.469 0.219,0.188 10 false 35 3.385,2.719 3.604,2.906 0.219,0.188 10 false 32 1.479,0.813 1.906,1.01 0.427,0.198 10 false SNS2 1.531,1.313 1.927,1.49 0.396,0.177 10 false ACC 1.521,1.792 1.917,1.969 0.396,0.177 10 false MI1+ 1.531,2.281 1.927,2.458 0.396,0.177 10 false MIC- 1.938,0.813 2.156,1 0.219,0.188 10 false 20 1.938,1.302 2.156,1.49 0.219,0.188 10 false 25 1.927,1.792 2.146,1.979 0.219,0.188 10 false 27 1.938,2.26 2.156,2.448 0.219,0.188 10 false 26 1.219,0.813 1.438,1 0.219,0.188 10 false 1 1.219,1.313 1.406,1.5 0.188,0.188 10 false 5 1.219,1.802 1.406,1.99 0.188,0.188 10 false 3 1.219,2.271 1.406,2.458 0.188,0.188 10 false 2 0.719,0.938 1.146,1.135 0.427,0.198 10 false SNS2 0.698,1.427 1.125,1.625 0.427,0.198 10 false MACC 0.802,1.906 1.229,2.104 0.427,0.198 10 false MIC+ 0.813,2.375 1.24,2.573 0.427,0.198 10 false MIC- 5.813,8.156 7.042,8.531 1.229,0.375 10 false Multi-media Module Receiver Assembly 5.813,7.99 6.063,8.198 0.25,0.208 10 false F77 0.188,8.156 1.531,8.375 1.344,0.219 10 false Map Light Assembly 0.188,7.99 0.438,8.198 0.25,0.208 10 false R7 3.844,7.354 4,7.5 0.156,0.146 10 false * 4.875,7.365 5.031,7.51 0.156,0.146 10 false * 6.125,5.281 6.552,5.479 0.427,0.198 10 false SNS2 6.146,5.771 6.573,5.969 0.427,0.198 10 false MIN+ 6.156,6.729 6.583,6.927 0.427,0.198 10 false MIN- 6.146,6.24 6.573,6.438 0.427,0.198 10 false MACC 6.146,7.198 6.573,7.396 0.427,0.198 10 false SGND 5.844,5.156 6.063,5.354 0.219,0.198 10 false 49 5.833,5.667 6.052,5.865 0.219,0.198 10 false 27 5.833,6.125 6.052,6.323 0.219,0.198 10 false 29 5.823,6.604 6.042,6.802 0.219,0.198 10 false 48 5.813,7.063 6.031,7.26 0.219,0.198 10 false 28 0.25,7.271 1.667,7.635 1.417,0.365 10 false Telephone Microphone Assembly 1.469,5.156 1.896,5.354 0.427,0.198 10 false SNS2 1.51,5.656 1.906,5.833 0.396,0.177 10 false MI1+ 1.521,6.135 1.917,6.313 0.396,0.177 10 false ACC 1.51,6.594 1.906,6.771 0.396,0.177 10 false MIC- 1.938,5.156 2.156,5.344 0.219,0.188 10 false 20 1.927,5.646 2.146,5.833 0.219,0.188 10 false 27 1.938,6.125 2.156,6.313 0.219,0.188 10 false 25 1.927,6.594 2.146,6.781 0.219,0.188 10 false 26 0.75,5.271 1.177,5.469 0.427,0.198 10 false SNS2 1.219,5.167 1.438,5.354 0.219,0.188 10 false 1 0.781,5.781 1.208,5.979 0.427,0.198 10 false MIC+ 1.219,5.667 1.396,5.854 0.177,0.188 10 false 3 0.719,6.25 1.208,6.458 0.49,0.208 10 false MACC 1.229,6.125 1.417,6.313 0.188,0.188 10 false 5 0.813,6.708 1.24,6.906 0.427,0.198 10 false MIC- 1.219,6.594 1.406,6.781 0.188,0.188 10 false 2 0.167,8.531 0.917,8.708 0.75,0.177 10 false *: Shielded

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION


PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.

Model:
Model Proceed to
w/o Telematics Transceiver A
w/ Telematics Transceiver B




A

2.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)

B

5.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the F77 multi-media module receiver assembly connector.


b.

Disconnect the R7 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-27 (MIN+) - R7-27 (MI1+) Always Below 1 Ω
F77-29 (MACC) - R7-25 (ACC) Always Below 1 Ω
F77-48 (MIN-) - R7-26 (MIC-) Always Below 1 Ω
F77-49 (SNS2) - R7-20 (SNS2) Always Below 1 Ω
F77-27 (MIN+) - Body ground Always 10 kΩ or higher
F77-28 (SGND) - Body ground Always 10 kΩ or higher
F77-29 (MACC) - Body ground Always 10 kΩ or higher
F77-48 (MIN-) - Body ground Always 10 kΩ or higher
F77-49 (SNS2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAP LIGHT ASSEMBLY
a.
E356115E04
1.573,0.073 1.927,0.365 0.354,0.292 1.573,1.792 1.927,2.083 0.354,0.292 0.917,3.052 1.188,2.688 true 1.313,3.042 1.469,2.677 true 1.667,3.042 1.719,2.698 true 2.292,3.031 2.219,2.698 true 2.552,1.469 2.406,1.083 true 1.198,1.479 1.406,1.083 true 1.969,1.458 1.698,1.073 true 1.583,1.469 1.563,1.083 true 0.677,3.083 1.073,3.26 0.396,0.177 10 false SNS2 1.167,3.083 1.563,3.26 0.396,0.177 10 false MIC- 1.531,3.083 1.927,3.26 0.396,0.177 10 false MIC+ 2.135,3.083 2.604,3.281 0.469,0.198 10 false MACC 2.469,1.5 2.865,1.677 0.396,0.177 10 false SNS2 1,1.479 1.354,1.646 0.354,0.167 10 false MI1+ 1.938,1.479 2.292,1.646 0.354,0.167 10 false ACC 1.479,1.479 1.833,1.646 0.354,0.167 10 false MIC- 1.708,0.135 1.854,0.313 0.146,0.177 10 false A 1.708,1.865 1.854,2.042 0.146,0.177 10 false B

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>ROOM LIGHT(for Front)>REMOVAL


b.

Remove the telephone microphone assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE AMPLIFIER>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-20 (SNS2) - B-1 (SNS2) Always Below 1 Ω
A-25 (ACC) - B-5 (MACC) Always Below 1 Ω
A-27 (MI1+) - B-3 (MIC+) Always Below 1 Ω
A-26 (MIC-) - B-2 (MIC-) Always Below 1 Ω
A-20 (SNS2) - A-25 (ACC) Always 10 KΩ or higher
A-20 (SNS2) - A-27 (MI1+) Always 10 KΩ or higher
A-20 (SNS2) - A-26 (MIC-) Always 10 KΩ or higher
A-25 (ACC) - A-27 (MI1+) Always 10 KΩ or higher
A-25 (ACC) - A-26 (MIC-) Always 10 KΩ or higher
A-27 (MI1+) - A-26 (MIC-) Always 10 KΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK TELEPHONE MICROPHONE ASSEMBLY

NG

4.CHECK TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a new or normally functioning one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE AMPLIFIER>REMOVAL


b.

Check if the same DTC is output again.

OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the F77 multi-media module receiver assembly connector.


b.

Disconnect the R7 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-49 (SNS2) - R7-20 (SNS2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - DCM [TELEMATICS TRANSCEIVER])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - DCM [TELEMATICS TRANSCEIVER])
a.

Disconnect the F77 multi-media module receiver assembly connector.


b.

Disconnect the P3 DCM (telematics transceiver) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-27 (MIN+) - P3-18 (MCO+) Always Below 1 Ω
F77-48 (MIN-) - P3-19 (MCO-) Always Below 1 Ω
F77-27 (MIN+) - Body ground Always 10 kΩ or higher
F77-48 (MIN-) - Body ground Always 10 kΩ or higher
F77-28 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (DCM [TELEMATICS TRANSCEIVER] - MAP LIGHT ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (DCM [TELEMATICS TRANSCEIVER] - MAP LIGHT ASSEMBLY)
a.

Disconnect the P3 DCM (telematics transceiver) connector.


b.

Disconnect the R7 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P3-33 (MCVD) - R7-25 (ACC) Always Below 1 Ω
P3-34 (MCI+) - R7-27 (MI1+) Always Below 1 Ω
P3-35 (MCI-) - R7-26 (MIC-) Always Below 1 Ω
P3-33 (MCVD) - Body ground Always 10 kΩ or higher
P3-34 (MCI+) - Body ground Always 10 kΩ or higher
P3-35 (MCI-) - Body ground Always 10 kΩ or higher
P3-32 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT MAP LIGHT ASSEMBLY
a.
E356115E04
1.573,0.073 1.927,0.365 0.354,0.292 1.573,1.792 1.927,2.083 0.354,0.292 0.917,3.052 1.188,2.688 true 1.313,3.042 1.469,2.677 true 1.667,3.042 1.719,2.698 true 2.292,3.031 2.219,2.698 true 2.552,1.469 2.406,1.083 true 1.198,1.479 1.406,1.083 true 1.969,1.458 1.698,1.073 true 1.583,1.469 1.563,1.083 true 0.677,3.083 1.073,3.26 0.396,0.177 10 false SNS2 1.167,3.083 1.563,3.26 0.396,0.177 10 false MIC- 1.531,3.083 1.927,3.26 0.396,0.177 10 false MIC+ 2.135,3.083 2.604,3.281 0.469,0.198 10 false MACC 2.469,1.5 2.865,1.677 0.396,0.177 10 false SNS2 1,1.479 1.354,1.646 0.354,0.167 10 false MI1+ 1.938,1.479 2.292,1.646 0.354,0.167 10 false ACC 1.479,1.479 1.833,1.646 0.354,0.167 10 false MIC- 1.708,0.135 1.854,0.313 0.146,0.177 10 false A 1.708,1.865 1.854,2.042 0.146,0.177 10 false B

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>ROOM LIGHT(for Front)>REMOVAL


b.

Remove the telephone microphone assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE AMPLIFIER>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-20 (SNS2) - B-1 (SNS2) Always Below 1 Ω
A-25 (ACC) - B-5 (MACC) Always Below 1 Ω
A-27 (MI1+) - B-3 (MIC+) Always Below 1 Ω
A-26 (MIC-) - B-2 (MIC-) Always Below 1 Ω
A-20 (SNS2) - A-25 (ACC) Always 10 KΩ or higher
A-20 (SNS2) - A-27 (MI1+) Always 10 KΩ or higher
A-20 (SNS2) - A-26 (MIC-) Always 10 KΩ or higher
A-25 (ACC) - A-27 (MI1+) Always 10 KΩ or higher
A-25 (ACC) - A-26 (MIC-) Always 10 KΩ or higher
A-27 (MI1+) - A-26 (MIC-) Always 10 KΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK DCM (TELEMATICS TRANSCEIVER)

NG

9.CHECK DCM (TELEMATICS TRANSCEIVER)
a.
E283057C25
1.625,0.646 2.021,0.854 0.396,0.208 0.729,2.677 1.24,2.073 true 1.365,2.865 1.49,2.063 true 2.406,2.938 1.583,2.083 true 0.24,0.135 0.552,0.292 0.313,0.156 10 false *a 0.563,2.719 0.958,2.875 0.396,0.156 10 false MCI- 1.146,2.896 1.646,3.073 0.5,0.177 10 false MCVD 2.26,2.979 2.76,3.156 0.5,0.177 10 false SGND 1.729,0.667 2.052,0.844 0.323,0.177 10 false P3
*a Component with harness connected
(DCM [Telematics Transceiver])


Disconnect the R7 map light assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
P3-33 (MCVD) - Body ground Engine switch on (ACC) 4 to 6 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P3-32 (SGND) - Body ground Always Below 1 Ω
P3-35 (MCI-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.CHECK TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE DCM (TELEMATICS TRANSCEIVER)

10.CHECK TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a new or normally functioning one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE AMPLIFIER>REMOVAL


b.

Check if the same DTC is output again.

OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)

NG

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY