Home › Engine / Hybrid System › 1UR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2016.08
RM2660E _51 Engine / Hybrid System _052772 1UR-FE ENGINE CONTROL _0254983 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0443  Evaporative Emission Control System Purge Control Valve Circuit  


DESCRIPTION

To reduce hydrocarbon emissions, evaporated fuel from the fuel tank is routed through a charcoal canister to the intake manifold for combustion in the cylinders.

The ECM changes the duty signal sent to the purge VSV (Vacuum Switching Valve for Purge Control) so that the intake amount of hydrocarbon emissions is appropriate for the driving conditions (engine load, engine speed, vehicle speed, etc.) after the engine is warmed up.

DTC No. DTC Detection Condition Trouble Area
P0443 Terminal voltage of the ECM output circuit does not correspond with the drive signals sent from the ECM to the purge VSV (1 trip detection logic).
·

Open or short in purge VSV circuit

·

Purge VSV

·

ECM



CONFIRMATION DRIVING PATTERN

A179391E01
1.525,1.949 1.755,2.124 0.230,0.174 10 [A] 2.846,1.949 3.076,2.124 0.230,0.174 10 [B] 3.892,3.005 4.122,3.179 0.230,0.174 10 [C] 4.574,1.338 4.804,1.512 0.230,0.174 10 [D] 5.097,3.005 5.327,3.179 0.230,0.174 10 [E] 0.509,2.071 0.887,2.255 0.378,0.184 10 Idling 4.224,2.524 5.010,2.837 0.786,0.313 10 10 minutes or more 2.594,2.524 3.380,2.837 0.786,0.313 10 15 minutes or more 1.31,2.524 2.105,2.689 0.795,0.165 10 Warming up 1.38,1.057 3.406,1.380 2.026,0.323 10 Between 40 km/h and 60 km/h (25 mph and 38 mph) 0.954,1.546 1.171,1.139 1.171,1.139 1.269,1.139 false 0.128,0.45 1.081,0.616 0.952,0.165 10 Vehicle Speed

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG) and turn the GTS on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the engine switch off and wait for at least 30 seconds.

5.

Turn the engine switch on (IG) and turn the GTS on.

6.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].

HINT:

The A/C switch and all accessory switches should be off.


7.

Idle the engine for 15 minutes or more [B].

HINT:

Check the EVAP (Purge) VSV item in the Data List. When the value of this item is between 5 and 95%, the judgment will be performed.


8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0443.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [D] through [E].



13.

Drive the vehicle at a constant speed between 40 and 60 km/h (25 and 38 mph) for 10 minutes [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


14.

Check the DTC judgment result [E].


WIRING DIAGRAM

A383880E01
0.833,3.833 1.448,4.125 0.615,0.292 10 false Battery 0.729,3 1.344,3.292 0.615,0.292 10 false P/I-B 2.323,3.969 3.198,4.177 0.875,0.208 10 false *1: for RHD 2.333,4.281 3.208,4.49 0.875,0.208 10 false *2: for LHD 1.75,2.479 3.344,2.719 1.594,0.24 10 false No. 2 Integration Relay 6.094,3.75 6.708,4.042 0.615,0.292 10 false ECM 5.771,2.083 6.385,2.375 0.615,0.292 10 false MREL 5.75,0.76 6.365,1.052 0.615,0.292 10 false PRG 3.76,1.208 4.375,1.5 0.615,0.292 10 false C55 3.76,1.365 4.708,1.656 0.948,0.292 10 false Purge VSV 1.479,1.688 2.656,1.99 1.177,0.302 10 false EFI MAIN NO. 1 1.063,1.042 1.719,1.438 0.656,0.396 10 false EFI MAIN NO. 1 2.313,1.042 3.031,1.271 0.719,0.229 10 false EFI NO. 2 4.99,2.063 5.281,2.313 0.292,0.25 10 false A52 5.375,2.063 5.667,2.313 0.292,0.25 10 false A38 5.375,0.875 5.667,1.125 0.292,0.25 10 false C45 4.99,0.875 5.281,1.125 0.292,0.25 10 false C46 0.531,2.177 0.781,2.396 0.25,0.219 10 false 1X 3.073,2.063 3.323,2.281 0.25,0.219 10 false 1S 3.073,1.365 3.323,1.583 0.25,0.219 10 false 1S 3.073,0.875 3.323,1.094 0.25,0.219 10 false 1S 0.333,2.156 0.51,2.375 0.177,0.219 10 false 1 3.115,0.688 3.292,0.906 0.177,0.219 10 false 1 3.552,0.729 3.729,0.948 0.177,0.219 10 false 1 3.115,1.156 3.292,1.375 0.177,0.219 10 false 4 3.115,1.854 3.292,2.073 0.177,0.219 10 false 8 4.729,0.74 4.906,0.958 0.177,0.219 10 false 2 4.969,0.667 5.313,0.917 0.344,0.25 10 false 63*1 5.365,0.677 5.708,0.927 0.344,0.25 10 false 63*2 4.969,1.865 5.313,2.115 0.344,0.25 10 false 34*1 5.354,1.865 5.698,2.115 0.344,0.25 10 false 34*2

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR EVAP CONTROL)
a.
A214696E01
0.151,0.262 0.897,0.425 0.746,0.163 10 Purge VSV 1.954,2.651 3.137,2.834 1.184,0.184 10 Hose (to Canister) 1.053,0.343 1.76,1.4 false 2.508,2.25 2.177,2.651 false

Connect the GTS to the DLC3.


b.

Disconnect the vacuum hose (charcoal canister side) from the purge VSV.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for EVAP Control.


f.

When the purge VSV is operated using the GTS, check whether the port of the purge VSV applies suction to your finger.

OK:
Tester Operation Specified Condition
VSV ON Purge VSV port applies suction to finger
VSV OFF Purge VSV port applies no suction to finger



g.

Reconnect the vacuum hose to the purge VSV.



OK

NG

2.INSPECT PURGE VSV
2.INSPECT PURGE VSV

OK

3.INSPECT PURGE VSV (POWER SOURCE)

NG

3.INSPECT PURGE VSV (POWER SOURCE)
a.
U162865E02
0.052,0 0.26,0.177 0.208,0.177 10 false *a 0.406,1.865 0.688,2.01 0.281,0.146 10 false C55

Disconnect the purge VSV connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C55-1 - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Purge VSV)


d.

Reconnect the purge VSV connector.



OK

4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR OR REPLACE FUSE (PURGE VSV - NO. 2 INTEGRATION RELAY)

4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)
a.

Disconnect the purge VSV connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
C55-2 - C46-63 (PRG) Always Below 1 Ω
C55-2 or C46-63 (PRG) - Body ground Always 10 kΩ or higher

for LHD
Tester Connection Condition Specified Condition
C55-2 - C45-63 (PRG) Always Below 1 Ω
C55-2 or C45-63 (PRG) - Body ground Always 10 kΩ or higher



d.

Reconnect the purge VSV connector.


e.

Reconnect the ECM connector.



OK

5.PERFORM CONFIRMATION DRIVING PATTERN

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.PERFORM CONFIRMATION DRIVING PATTERN
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).


e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.


g.

Idle the engine for 15 minutes or more.


h.

Turn the GTS on.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


j.

Input the DTC: P0443.


k.

Check the DTC judgment result.

Result
Result Proceed to
NORMAL (DTC is not output) A
ABNORMAL (DTC P0443 is output) B

HINT:

If the judgment result shows INCOMPLETE or N/A, drive the vehicle at a constant speed between 40 and 60 km/h (25 and 38 mph) for 10 minutes and check the DTC judgment result again.




A

B