Home › Engine / Hybrid System › 1VD-FTV (FUEL) › FUEL PUMP › from 2016.08
RM2660E _51 Engine / Hybrid System _052783 1VD-FTV FUEL _0255117 FUEL PUMP A

1VD-FTV FUEL  FUEL PUMP  REMOVAL  


PROCEDURE

Hide 77100U 1.REMOVE FUEL TANK SUB-ASSEMBLY

Hide 77020A 2.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

NOTICE:

Protect the connector and tube joint of the fuel tank vent tube assembly with vinyl tape to prevent foreign matter from entering. Then clean off any mud or other foreign matter before proceeding with work.


a.
A392967C01
0.802,0.771 1,0.927 0.198,0.156 10 true *a 1.469,0.938 1.667,1.094 0.198,0.156 10 true *a
*a Co-rotation Prevention Check Mark
V100135

Front


Apply a co-rotation prevention check mark to the fuel tank vent tube assembly and fuel tank assembly.

NOTICE:
·

The fuel tank assembly cutout is attached to the protrusion on the fuel tank vent tube assembly.

·

If the fuel tank vent tube assembly and fuel tank assembly are not firmly attached and the fuel pump gauge retainer is rotated, the fuel tank vent tube assembly will co-rotate and result in the fuel tank vent tube assembly and fuel tank assembly being damaged.

·

Make sure to apply a co-rotation prevention check mark to prevent the fuel tank vent tube assembly from co-rotating.




b.
A393131C01
0.719,4.396 1.646,4.135 true 1.208,2.469 1.625,2.74 true 1.667,2.854 2.469,2.583 true 1.063,1.146 1.458,1.281 true 0.615,0.635 0.865,0.802 true 0.792,2.802 0.594,2.292 true 1.5,1.24 1.813,1.396 0.313,0.156 10 false *1 0.458,0.5 0.771,0.656 0.313,0.156 10 false *a 2.479,2.458 2.792,2.615 0.313,0.156 10 false *b 1.073,2.323 1.385,2.479 0.313,0.156 10 false *c 0.552,4.333 0.865,4.49 0.313,0.156 10 false *d 0.49,2.125 0.802,2.281 0.313,0.156 10 false *1
*1 Fuel Pump Gauge Retainer
*a SST (claw set)
*b Rib
*c Cutout
*d SST (Claw Set) Incorrect Installation Point (Rotational Start Point Mark of Fuel Pump Gauge Retainer)


Set 4 SSTs (claw sets) to the fuel pump gauge retainer and temporarily install.

SST
09808-14031  (09808-01080, 09808-01090, 09808-01100)

NOTICE:
·

Align the cutout of SST (claw set) to the rib of the fuel pump gauge retainer.

·

Do not place SST on the rotational start point mark of the fuel pump gauge retainer, otherwise SST (claw set) cannot be set correctly.




c.
A387296C02
2.333,1.313 2.51,1.104 2.51,1.104 2.698,1.104 false 1.146,0.74 1.344,0.74 1.344,0.74 1.75,1.052 false 1.115,2.063 1.313,2.063 1.313,2.063 1.563,1.833 false 2.74,1.021 3.052,1.177 0.313,0.156 10 false *1 0.958,0.667 1.271,0.823 0.313,0.156 10 false *a 0.948,1.979 1.26,2.135 0.313,0.156 10 false *b
*1 Fuel Pump Gauge Retainer
*a SST (Claw Set)
*b Hook
V100135

Press
V100136

SST (Bolt)


While firmly pressing the claw of SST into rib of the fuel pump gauge retainer, tighten the bolt.


d.
A392968C01
0.583,0.5 1.094,0.5 true 0.854,1.781 1.219,1.615 true 0.406,0.385 0.719,0.542 0.313,0.156 10 false *a 0.688,1.729 0.875,1.896 0.188,0.167 10 true *b
*a SST (Plate)
*b SST (Claw Set)
V100135

SST (Bolt)


Temporarily install SST (plate) to SST (claw set) with 4 SSTs (bolts).

SST
09808-14031  (09808-01030, 09808-01090)


e.
A392969C01
1.771,1.167 2.708,1.167 true 0.708,0.698 1.135,0.698 true 2.74,1.073 2.948,1.229 0.208,0.156 10 true *a 0.635,0.604 0.844,0.76 0.208,0.156 10 true *b
*a Center of Fuel Pump Gauge Retainer
*b SST (Plate)
V100135

Front


Adjust the position of SST (plate) so that the setting hole of SST (handle) aligns with the center of the fuel pump gauge retainer.


f.
A393430C01
0.844,3.792 0.74,3.354 true 2.26,3.177 1.875,3.385 true 2.531,3.583 1.719,4.021 true 1.333,1.323 0.469,1.063 true 1.531,0.365 1.615,0.688 true 0.635,3.167 0.948,3.323 0.313,0.156 10 false *1 1.417,0.177 1.729,0.333 0.313,0.156 10 false *a 2.281,3.063 2.594,3.219 0.313,0.156 10 false *b 0.292,0.948 0.604,1.104 0.313,0.156 10 false *c 2.552,3.438 2.865,3.594 0.313,0.156 10 false *d
*1 Fuel Pump Gauge Retainer
*a SST (Plate)
*b SST (Claw Set)
*c SST (Bolt)
*d Rib
V113147

Press


While firmly pressing the SST (claw set) into rib of the fuel pump gauge retainer, tighten SST (bolt).


g.

Install SST (handle) to SST (plate).

SST
09808-14031  (09808-01010, 09808-01020)


h.
A392970C01
0.729,1.448 1.125,1.448 true 1.917,0.781 2.302,1.146 true 0.563,1.333 0.875,1.49 0.313,0.156 10 false *a 1.781,0.615 2.094,0.771 0.313,0.156 10 false *b
*a SST (Plate)
*b SST (Handle)
V100135

Loosen


Slowly loosen the fuel pump gauge retainer by approximately 90°.

NOTICE:
·

Do not use any tools other than SST, such as a screwdriver, etc.

·

Do not use excessive force when pressing down on SST, as the fuel tank vent tube assembly will place excessive force on the pump gauge retainer and be difficult to remove, and parts may be damaged.

·

Do not use an impact wrench or turn the SST handle with excessive force, as parts may be damaged.




i.

While one person slowly loosens the fuel pump gauge retainer, have another person press down the rising fuel tank vent tube assembly, securely attach the protrusion of the fuel tank vent tube assembly to the groove of the fuel tank assembly, and then remove the fuel pump gauge retainer while making sure that the fuel tank vent tube assembly is properly aligned.

A392971C01
0.417,1.365 1.125,1.125 true 2.583,0.396 2.167,0.813 true 4.073,1.365 4.906,1.125 true 0.25,1.281 0.563,1.438 0.313,0.156 10 false *a 2.563,0.24 2.875,0.396 0.313,0.156 10 false *b 0.448,0.177 0.76,0.333 0.313,0.156 10 false *c 1.323,0.26 1.635,0.417 0.313,0.156 10 false *d 2.656,2.521 2.844,2.677 0.188,0.156 10 true *e 3.281,2.677 3.469,2.833 0.188,0.156 10 true *e 2.49,0.896 2.802,1.052 0.313,0.156 10 false *c 1.802,0.365 2.115,0.521 0.313,0.156 10 false *d 5.625,0.927 5.938,1.083 0.313,0.156 10 false *c 5.063,0.323 5.375,0.479 0.313,0.156 10 false *d 5.625,0.385 5.938,0.542 0.313,0.156 10 false *d 3.906,1.271 4.219,1.427 0.313,0.156 10 false *a 4.656,0.573 4.969,0.729 0.313,0.156 10 false *c
*a SST (Plate) *b SST (Handle)
*c Person in Charge of Loosening *d Person in Charge of Supporting
*e Co-rotation Prevention Check Mark - -
V100135

Front - -


NOTICE:
·

The fuel tank vent tube assembly is equipped with a spring that pushes against the bottom of the fuel tank assembly to constantly lift the fuel tank vent tube assembly upwards.

·

If the fuel tank vent tube assembly and fuel tank assembly are not firmly attached and the fuel pump gauge retainer is rotated, the fuel tank vent tube assembly will co-rotate and result in the fuel tank vent tube assembly and fuel tank assembly being damaged.

·

Do not rotate the fuel pump gauge retainer when the co-rotation prevention check mark is out of place.

·

Do not bend the arm of the fuel sender gauge assembly.




j.

Remove the gasket from the fuel tank sub-assembly.