Home › Engine / Hybrid System › 1VD-FTV (FUEL) › FUEL TANK › from 2015.08
RM2660E _51 Engine / Hybrid System _052783 1VD-FTV FUEL _0255108 FUEL TANK A

1VD-FTV FUEL  FUEL TANK  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 77310A 2.REMOVE FUEL TANK CAP ASSEMBLY

Hide 77606 3.REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY

a.
A175014

Remove the 5 bolts and fuel tank protector.


Hide 77209C 4.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A175058

Detach the fuel tube clamp.


b.

Disconnect the fuel tank main tube.


Hide 5.DRAIN FUEL

a.

for Double Tank Type:

i.

Connect the intelligent tester to the DLC3.


ii.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



iii.

Turn the intelligent tester on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the Intank Fuel Pump Relay.

CAUTION:
·

Do not smoke or be near an open flame when working on the fuel system.

·

Secure good ventilation.



HINT:
A181435E04
1.854,1 0.969,1 true 1.833,3.313 0.958,3.313 true 0.042,0.042 1.667,0.427 1.625,0.385 12 true for Single Tank Type: 0.063,2.365 1.75,2.771 1.688,0.406 12 true for Double Tank Type: 0.604,0.906 0.938,1.104 0.333,0.198 10 true Port 0.583,3.219 0.938,3.417 0.354,0.198 10 true Port

for Single Tank Type:

Remove the fuel tube joint clip and disconnect the fuel tank return tube, and drain fuel from the port shown in the illustration.

for Double Tank Type:

If the fuel pump does not operate, remove the fuel tube joint clip and disconnect the fuel tank return tube, and drain fuel from the port shown in the illustration.




Hide 6.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


a.

Disconnect the cables from the negative (-) main battery and sub-battery terminals.


Hide 71300S 7.REMOVE REAR NO. 1 SEAT ASSEMBLY RH (for 60/40 Split Seat Type 40 Side)

Hide 71400S 8.REMOVE REAR NO. 1 SEAT ASSEMBLY LH (for 60/40 Split Seat Type 60 Side)

Hide 9.REMOVE REAR NO. 2 SEAT ASSEMBLY

a.

for Face to Face Seat Type:

Remove the rear No. 2 seat assembly (See page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY(for Face to Face Seat Type)>REMOVAL).


b.

except Face to Face Seat Type:

Remove the rear No. 2 seat assembly (See page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY(except Face to Face Seat Type)>REMOVAL).


Hide 71845B 16.REMOVE REAR SEAT COVER CAP (w/ Rear No. 2 Seat, except Face to Face Seat Type)

Hide 62520P 17.REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH

a.

w/ Sliding Roof:

Remove the front quarter trim panel assembly LH (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (w/ Sliding Roof)>REMOVAL).


b.

w/o Sliding Roof:

Remove the front quarter trim panel assembly LH (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (w/o Sliding Roof)>REMOVAL).


Hide 62510P 18.REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH

a.

w/ Sliding Roof:

Remove the front quarter trim panel assembly RH (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (w/ Sliding Roof)>REMOVAL).


b.

w/o Sliding Roof:

Remove the front quarter trim panel assembly RH (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (w/o Sliding Roof)>REMOVAL).


Hide 87217B 19.REMOVE AIR DUCT PLUG (w/ Rear Air Conditioning System)

Hide 87174 20.REMOVE REAR AIR DUCT GUIDE (w/ Rear Air Conditioning System)

Hide 58510D 21.REMOVE FRONT FLOOR CARPET ASSEMBLY

E157065

a.

w/ Rear Air Conditioning System:

Fold back the floor carpet.

HINT:

Fold back the floor carpet so that the air duct can be removed.



b.

w/o Rear Air Conditioning System:

Fold back the floor carpet.

HINT:

Fold back the floor carpet so that the service hole cover can be removed.



Hide 58329F 22.REMOVE REAR FLOOR NO. 2 SERVICE HOLE COVER

a.
A181426

w/ Rear Air Conditioning System:

Remove the 2 screws and air duct.


b.
A181427

Remove the service hole cover.


c.
A181410E03
0.073,0.073 1.677,0.458 1.604,0.385 12 true for Single Tank Type: 0.073,2.365 1.771,2.76 1.698,0.396 12 true for Double Tank Type:

Disconnect the fuel pump and fuel sender gauge connector.


Hide 77204A 23.DISCONNECT FUEL TANK RETURN TUBE

a.
U163012E01
0.51,2.964 0.813,3.137 0.303,0.173 10 Pipe 1.468,2.985 2.027,3.131 0.559,0.145 10 Retainer 0.687,4.143 1.357,4.296 0.670,0.152 10 Connector 2.007,4.023 2.477,4.197 0.470,0.174 10 O-Ring 2.52,2.998 3.255,3.170 0.735,0.172 10 Nylon Tube 1.421,3.071 1.29,3.071 1.29,3.071 0.979,3.429 false 2.484,3.087 2.352,3.087 2.352,3.087 2.352,3.492 false 1.09,3.989 1.09,4.16 false 1.968,4.111 1.714,4.111 1.714,4.111 1.541,3.854 false 1.646,3.854 1.815,4.111 false 1.1,1.72 1.658,1.865 0.559,0.145 10 Retainer 1.069,1.806 0.969,1.806 0.969,1.806 0.858,2.012 false

Detach the fuel tube clamp.


b.

Pull up the retainer and disconnect both ends of the fuel tank return tube.

NOTICE:
·

Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.




Hide 24.DISCONNECT NO. 2 FUEL TANK BREATHER TUBE (for Single Tank Type)

a.
A176372

Detach the fuel tube clamp.


b.

Disconnect the No. 2 fuel tank breather tube from the body.


Hide 77206C 25.DISCONNECT NO. 2 FUEL MAIN TUBE SUB-ASSEMBLY (for Double Tank Type)

a.
A175061E01
1.35,2.663 1.653,2.836 0.303,0.173 10 Pipe 2.676,2.699 3.235,2.844 0.559,0.145 10 Retainer 2.61,3.191 3.280,3.344 0.670,0.152 10 Connector 2.615,3.952 3.085,4.126 0.470,0.174 10 O-Ring 0.438,3.411 1.173,3.583 0.735,0.172 10 Nylon Tube 2.629,2.784 2.498,2.784 2.498,2.784 2.132,3.205 false 1.352,3.51 1.483,3.51 1.483,3.51 1.67,3.912 false 1.74,2.765 1.871,2.765 1.871,2.765 1.99,3.019 false 2.567,3.28 2.233,3.28 false 2.106,3.622 2.891,3.622 2.891,3.622 2.891,3.92 false 2.106,3.754 2.891,3.754 false 0.764,0.507 1.322,0.653 0.559,0.145 10 Retainer 0.716,0.593 0.585,0.593 0.585,0.593 0.476,0.719 false

Detach the fuel tube clamp.


b.

Pull up the retainer and disconnect the fuel main tube.

NOTICE:
·

Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.




Hide 26.DISCONNECT NO. 2 FUEL TANK BREATHER TUBE (for Double Tank Type)

a.
A175063E01
1.34,2.8 1.643,2.973 0.303,0.173 10 Pipe 2.686,2.835 3.245,2.981 0.559,0.145 10 Retainer 2.629,3.23 3.299,3.383 0.670,0.152 10 Connector 2.625,3.943 3.095,4.117 0.470,0.174 10 O-Ring 0.273,3.382 1.007,3.554 0.735,0.172 10 Nylon Tube 2.639,2.921 2.508,2.921 2.508,2.921 2.142,3.342 false 1.186,3.481 1.317,3.481 1.317,3.481 1.505,3.883 false 1.73,2.901 1.861,2.901 1.861,2.901 2,3.155 false 2.586,3.319 2.252,3.319 false 2.116,3.612 2.9,3.612 2.9,3.612 2.9,3.91 false 2.116,3.744 2.9,3.744 false 2.647,0.257 3.206,0.403 0.559,0.145 10 Retainer 2.6,0.342 2.469,0.342 2.469,0.342 2.38,0.445 false

Detach the fuel tube clamp.


b.

Pull up the retainer and disconnect the fuel tank breather tube.

NOTICE:
·

Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.




Hide 27.DISCONNECT FUEL TANK BREATHER TUBE (for Single Tank Type)

a.
A176312E01
1.661,2.152 2.220,2.298 0.559,0.145 10 Retainer 1.631,2.238 1.531,2.238 1.531,2.238 1.42,2.444 false

Detach the fuel tube clamp.


b.

Pull up the retainer and disconnect the fuel tank breather tube.

NOTICE:
·

Do not use any tools in this procedure.

·

Check for any dirt and foreign matter contamination in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-rings or cause leaks in the seal between the pipe and connector.




Hide 28.DISCONNECT FUEL TANK BREATHER TUBE (for Double Tank Type)

a.
A175065E02
2.71,0.823 3.268,0.969 0.559,0.145 10 Retainer 2.679,0.909 2.613,0.909 2.613,0.909 2.537,1.106 false

Detach the fuel tube clamp.


b.

Pull up the retainer and disconnect the fuel tank breather tube.

NOTICE:
·

Do not use any tools in this procedure.

·

Check for any dirt and foreign matter contamination in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-rings or cause leaks in the seal between the pipe and connector.




Hide 29.DISCONNECT FUEL TANK TO FILLER PIPE HOSE (for Single Tank Type)

a.
A176314

Disconnect the hose from the filler pipe.


Hide 30.DISCONNECT FUEL TANK TO FILLER PIPE HOSE (for Double Tank Type)

a.
A175067

Disconnect the hose from the filler pipe.


Hide 77100U 31.REMOVE FUEL TANK SUB-ASSEMBLY

a.

Place a transmission jack under the fuel tank.


b.
A175024

Remove the 2 bolts, 2 clips, 2 pins and 2 fuel tank bands.


c.

Lower the transmission jack to remove the fuel tank from the vehicle.

NOTICE:

Do not allow the fuel tank to contact the vehicle, especially the differential.


HINT:

Lower the transmission jack slowly.



Hide 32.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY AND FUEL TANK RETURN TUBE (for Single Tank Type)

a.
A181404E01
2.007,3.974 3.174,4.139 1.167,0.165 10 Fuel Suction Plate 2.164,2.315 3.156,2.468 0.993,0.153 10 Fuel Tank Tube 2.345,3.377 2.846,3.542 0.501,0.165 10 O-Ring 0.041,3.85 0.992,4.027 0.952,0.177 10 Tube Joint Clip 0.199,2.191 0.916,2.356 0.717,0.165 10 Tube Joint 2.127,2.4 1.99,2.4 1.99,2.4 1.873,2.835 false 1.045,2.286 1.182,2.286 1.182,2.286 1.372,2.846 false 0.606,3.824 0.606,3.698 0.606,3.698 1.167,3.347 false 1.966,4.056 1.85,4.056 1.85,4.056 1.713,3.879 false 1.748,3.465 2.302,3.465 false 1.746,3.605 2.154,3.605 2.154,3.605 2.154,3.471 false

Remove the 2 fuel tube joint clips and pull out the 2 fuel tubes.

NOTICE:
·

Remove any dirt and foreign matter on the fuel tube joint before performing this work.

·

Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the nylon tube.

·

Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tubes.




b.
A175030

Remove the 2 fuel tubes from the fuel tank.


Hide 33.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY, FUEL TANK RETURN TUBE AND NO. 2 FUEL MAIN TUBE SUB-ASSEMBLY (for Double Tank Type)

a.
A175068E01
0.029,3.769 0.829,4.084 0.801,0.315 10 Fuel Suction Plate 2.192,2.467 3.184,2.620 0.993,0.153 10 Fuel Tank Tube 2.436,3.573 2.937,3.738 0.501,0.165 10 O-Ring 0.027,2.861 0.979,3.038 0.952,0.177 10 Tube Joint Clip 0.325,2.445 1.041,2.610 0.717,0.165 10 Tube Joint 2.155,2.552 2.018,2.552 2.018,2.552 1.935,3.094 false 1.17,2.541 1.308,2.541 1.308,2.541 1.497,3.1 false 1.839,3.66 2.393,3.66 false 1.837,3.786 2.245,3.786 2.245,3.786 2.245,3.667 false 1.194,2.967 1.332,2.967 1.332,2.967 1.332,3.425 false 0.998,3.87 1.136,3.87 1.136,3.87 1.42,3.664 false

Remove the 3 fuel tube joint clips and pull out the 3 fuel tubes.

NOTICE:
·

Remove any dirt and foreign matter on the fuel tube joint before performing this work.

·

Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the nylon tube.

·

Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tubes.




b.
A175070

Remove the 3 fuel tubes from the fuel tank.


Hide 77020A 34.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

Hide 77213B 35.REMOVE FUEL TANK TO FILLER PIPE HOSE

a.
A176316

Remove the hose from the fuel tank.


Hide 77697 36.REMOVE NO. 1 FUEL TANK HEAT INSULATOR

a.
U163014E02
0.729,3.365 0.854,3.51 0.125,0.146 10 false 1 1.677,3.354 1.802,3.5 0.125,0.146 10 false 2 2.625,3.354 2.75,3.5 0.125,0.146 10 false 3

Remove the fuel tube clamp from the heat insulator.


b.

Using needle-nose pliers, remove the 4 clips shown in the illustration and then remove the heat insulator.