Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › PARK / NEUTRAL POSITION SWITCH › from 2017.08
RM2660E _52 Drivetrain _066407 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0323659 PARK / NEUTRAL POSITION SWITCH A

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  PARK / NEUTRAL POSITION SWITCH  INSTALLATION  


PROCEDURE

Hide 84540 1.INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

HINT:

Make sure that the manual valve lever shaft has not been rotated prior to installing the park/neutral position switch assembly as the detent spring may become detached from the manual valve lever shaft.


a.

Clean the bolt and the bolt hole.


b.

Apply adhesive to 2 or 3 threads on the end of the bolt.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



c.
C380065

Temporarily install the park/neutral position switch assembly with the bolt.

HINT:

Tighten the bolt to the specified torque when adjusting the park/neutral position switch assembly.



d.
C380064

Install the lock washer and the lock nut to the park/neutral position switch assembly.

Torque:
6.9 N*m (70 kgf*cm, 61 in.*lbf)


e.
C380062

Temporarily install the transmission control shaft lever RH to the manual valve lever shaft with the spring washer and nut.

HINT:

Tighten the nut to the specified torque when adjusting the park/neutral position switch assembly.



f.
C380067C01
2.01,1.073 2.302,1.354 2.302,1.354 2.594,1.354 false 2.625,1.26 2.844,1.479 0.219,0.219 10 false *1 2.292,0.25 2.49,0.458 0.198,0.208 10 false N 1.51,0.021 1.667,0.219 0.156,0.198 10 false P 1.906,0.375 2.063,0.573 0.156,0.198 10 false R
*1 Transmission Control Shaft Lever RH


Turn the transmission control shaft lever RH counterclockwise until it stops, and then turn it clockwise 2 notches to set it to the N position.


g.

Remove the nut, spring washer and transmission control shaft lever RH from the manual valve lever shaft.


h.
C380066C01
2.229,0.896 2.417,0.333 2.417,0.333 2.615,0.333 true 0.771,0.896 1.021,0.896 1.021,0.896 1.844,1.521 true 2.635,0.229 2.865,0.458 0.229,0.229 10 false *a 0.583,0.813 0.771,1.031 0.188,0.219 10 false *b
*a Neutral Basic Line
*b Groove


Align the groove with the neutral basic line.


i.

Hold the park/neutral position switch assembly in the position described above and tighten the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


j.
C382623

Using a screwdriver, bend the tabs of the lock washer.

NOTICE:
·

Be careful not to damage the park/neutral position switch assembly.

·

Bend at least 2 of the lock washer tabs.



HINT:

Tape the screwdriver tip before use.



k.

Install the transmission control rod bush and collar to the transmission control shaft lever RH.


l.
C175585

Install the transmission control shaft lever RH with the spring washer and nut.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)


m.

Connect the park/neutral position switch assembly connector.


Hide 33702B 2.CONNECT FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY

C380061

a.

Connect the floor shift gear shifting rod sub-assembly to the transmission control shaft lever RH with the pin.


b.

Install a new clip.


Hide 84540 4.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY