Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE) › from 2017.08
RM2660E _52 Drivetrain _066407 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0327282 AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE) C

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE)  P0705  Transmission Range Sensor Circuit Malfunction (PRNDL Input)  


DESCRIPTION

The park/neutral position switch assembly detects the shift lever position and sends signals to the ECM.

DTC No. DTC Detection Condition Trouble Area
P0705 One of the following conditions is met:
(A) Any 2 or more of the following signals are ON simultaneously (2 trip detection logic):
·

One of the following conditions is met.

-

P input signal is ON

-

N input signal is ON

-

NSW input signal is ON


·

R input signal

·

D input signal


(B) Any of the following signals is ON for 2.0 seconds or more with the shift lever in S (2 trip detection logic):
·

P input signal

·

N input signal

·

NSW input signal

·

R input signal


(C) All signals are OFF simultaneously for NSW, P, R, N and D (2 trip detection logic).
·

Open or short in park/neutral position switch assembly circuit

·

Transmission control switch (lower shift lever assembly)

·

Park/neutral position switch assembly

·

ECM



MONITOR DESCRIPTION

This DTC indicates a problem with the park/neutral position switch assembly and the wire harness in the park/neutral position switch assembly circuit.

The park/neutral position switch assembly detects the shift lever position and sends signals to the ECM.

For safety, the park/neutral position switch assembly detects the shift lever position so that the engine can be started only when the shift lever is in P or N.

The park/neutral position switch assembly sends a signal to the ECM according to the shift lever position (P, R, N, D or S). The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

C330136E13
5.969,0.615 6.427,0.823 0.458,0.208 10 false 12 V 4.875,0.927 5.333,1.135 0.458,0.208 10 false C45 4.938,0.729 5.396,0.938 0.458,0.208 10 false 48 5.292,0.802 5.75,1.01 0.458,0.208 10 false NSW 3.76,0.802 4.219,1.01 0.458,0.208 10 false 4 3.521,0.802 3.979,1.01 0.458,0.208 10 false B 2.75,0.813 3.208,1.021 0.458,0.208 10 false L 2.542,0.813 3,1.021 0.458,0.208 10 false 5 2.74,2.146 3.198,2.354 0.458,0.208 10 false RB 2.542,2.156 3,2.365 0.458,0.208 10 false 2 5.292,1.25 5.75,1.458 0.458,0.208 10 false P 3.76,1.25 4.219,1.458 0.458,0.208 10 false 6 3.438,1.25 3.896,1.458 0.458,0.208 10 false PL 5.292,1.854 5.75,2.063 0.458,0.208 10 false R 3.76,1.854 4.219,2.063 0.458,0.208 10 false 1 3.438,1.854 3.896,2.063 0.458,0.208 10 false RL 5.292,2.448 5.75,2.656 0.458,0.208 10 false N 3.76,2.448 4.219,2.656 0.458,0.208 10 false 9 3.438,2.448 3.896,2.656 0.458,0.208 10 false NL 5.292,3.052 5.75,3.26 0.458,0.208 10 false D 3.76,3.052 4.219,3.26 0.458,0.208 10 false 7 3.438,3.052 3.896,3.26 0.458,0.208 10 false DL 1.927,3.625 2.385,3.833 0.458,0.208 10 false C24 1.927,3.823 4.594,4.031 2.667,0.208 10 false Park/Neutral Position Switch Assembly 0.927,0.927 1.938,1.135 1.01,0.208 10 false to ST Relay 0.406,2.281 2.229,2.49 1.823,0.208 10 false from BKUP LP Fuse 0.083,4.76 1.854,4.969 1.771,0.208 10 false from ECU-IG NO. 2 Fuse 2.208,5.219 2.667,5.427 0.458,0.208 10 false E52 2.208,5.406 4.448,5.615 2.24,0.208 10 false Transmission Control Switch 5.292,4.635 5.75,4.844 0.458,0.208 10 false S 3.75,4.635 4.208,4.844 0.458,0.208 10 false 7 3.521,4.635 3.979,4.844 0.458,0.208 10 false S 2.74,4.635 3.198,4.844 0.458,0.208 10 false IG 2.542,4.635 3,4.844 0.458,0.208 10 false 3 4.938,1.177 5.396,1.385 0.458,0.208 10 false 27 4.938,1.781 5.396,1.99 0.458,0.208 10 false 26 4.938,2.375 5.396,2.583 0.458,0.208 10 false 50 4.938,2.979 5.396,3.188 0.458,0.208 10 false 49 4.938,4.563 5.396,4.771 0.458,0.208 10 false 27 5.677,6.052 6.51,6.26 0.833,0.208 10 false ECM 4.875,1.365 5.333,1.573 0.458,0.208 10 false C45 4.875,1.969 5.333,2.177 0.458,0.208 10 false C45 4.875,2.573 5.333,2.781 0.458,0.208 10 false C45 4.875,3.167 5.333,3.375 0.458,0.208 10 false C45 4.875,4.76 5.333,4.969 0.458,0.208 10 false A38

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Perform registration and/or initialization when parts related to the automatic transmission are replaced (See page Drivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE)>PRECAUTION).



HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the engine switch on (IG).*1

2.

Wait with the shift lever in each position (P, R, N and D) for 60 seconds or more.*2

3.

Wait for 2 seconds or more with the shift lever in S.*3

4.

Turn the engine switch off.

5.

Perform steps (*1) through (*3) again.



DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the engine switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG).


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

According to the display on the GTS, read the Data List.

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Neutral Position SW Signal Park/neutral position switch status/
ON or OFF
·

ON: Shift lever in P or N

·

OFF: Shift lever not in P or N


When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
Shift SW Status (P Range) Park/neutral position switch status/
ON or OFF
·

ON: Shift lever in P

·

OFF: Shift lever not in P


When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
Shift SW Status (R Range) Park/neutral position switch status/
ON or OFF
·

ON: Shift lever in R

·

OFF: Shift lever not in R


When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
Shift SW Status (N Range) Park/neutral position switch status/
ON or OFF
·

ON: Shift lever in N

·

OFF: Shift lever not in N


When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
Sports Mode Selection SW Sport mode select switch status/
ON or OFF
·

ON: Shift lever in S, "+" or "-"

·

OFF: Shift lever not in S, "+" or "-"


-
Shift SW Status (D Range) Park/neutral position switch status/
ON or OFF
·

ON: Shift lever in D, S, "+" or "-"

·

OFF: Shift lever not in D, S, "+" or "-"


When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH)
a.
U164954E03
1.802,1.01 2.177,0.323 false 0.365,1.042 0.74,1.271 0.375,0.229 10 false C24 2.229,0.229 2.542,0.427 0.313,0.198 10 false RB 0.052,0 0.365,0.198 0.313,0.198 10 false *a

Disconnect the park/neutral position switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C24-2 (RB) - Body ground Engine switch on (IG) 11 to 14 V
C24-2 (RB) - Body ground Engine switch off Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (NSW TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (NSW TERMINAL VOLTAGE)
a.
U164955E03
2.115,1.021 2.385,0.333 false 0.052,0 0.365,0.198 0.313,0.198 10 false *a 2.448,0.24 2.76,0.438 0.313,0.198 10 false B 0.375,1.042 0.75,1.271 0.375,0.229 10 false C24

Disconnect the park/neutral position switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C24-4 (B) - Body ground Engine switch on (IG) 11 to 14 V
C24-4 (B) - Body ground Engine switch off Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)



OK

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.
C197712E95
1.844,0.958 2.219,0.417 false 1.292,0.958 0.917,0.417 false 2.094,1.292 2.458,1.833 false 0.99,1.833 1.365,1.292 false 1.604,0.958 1.521,0.417 false 2.052,1.833 1.969,1.292 false 1.635,1.833 1.719,1.292 false 2.292,0.302 2.604,0.5 0.313,0.198 10 false RL 0.052,0.073 0.365,0.271 0.313,0.198 10 false *a 0.792,0.302 1.104,0.5 0.313,0.198 10 false B 2.531,1.75 2.844,1.948 0.313,0.198 10 false L 0.76,1.75 1.073,1.948 0.313,0.198 10 false NL 1.292,0.302 1.604,0.5 0.313,0.198 10 false RB 2.125,1.75 2.438,1.948 0.313,0.198 10 false PL 1.406,1.75 1.719,1.948 0.313,0.198 10 false DL

Disconnect the park/neutral position switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (B) - 5 (L) Shift lever in P or N Below 1 Ω
2 (RB) - 6 (PL) Shift lever in P Below 1 Ω
2 (RB) - 1 (RL) Shift lever in R Below 1 Ω
2 (RB) - 9 (NL) Shift lever in N Below 1 Ω
2 (RB) - 7 (DL) Shift lever in D, S, "+" or "-" Below 1 Ω
4 (B) - 5 (L) Shift lever not in P or N 10 kΩ or higher
2 (RB) - 6 (PL) Shift lever not in P 10 kΩ or higher
2 (RB) - 1 (RL) Shift lever not in R 10 kΩ or higher
2 (RB) - 9 (NL) Shift lever not in N 10 kΩ or higher
2 (RB) - 7 (DL) Shift lever not in D, S, "+" or "-" 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Park/Neutral Position Switch Assembly)



OK

4.CHECK HARNESS AND CONNECTOR (BATTERY - TRANSMISSION CONTROL SWITCH)

NG

4.CHECK HARNESS AND CONNECTOR (BATTERY - TRANSMISSION CONTROL SWITCH)
a.
U148280E06
1.802,1.052 2.344,0.74 false 0.052,0.104 0.365,0.302 0.313,0.198 10 false *a 2.385,0.625 2.698,0.823 0.313,0.198 10 false IG 0.531,1 0.906,1.229 0.375,0.229 10 false E52

Disconnect the transmission control switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E52-3 (IG) - Body ground Engine switch on (IG) 11 to 14 V
E52-3 (IG) - Body ground Engine switch off Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Transmission Control Switch)



OK

5.INSPECT TRANSMISSION CONTROL SWITCH (LOWER SHIFT LEVER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT TRANSMISSION CONTROL SWITCH (LOWER SHIFT LEVER ASSEMBLY)
a.
C203344E50
1.635,0.729 1.104,0.292 false 1.115,1.427 1.656,1.01 false 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 0.896,0.188 1.135,0.385 0.24,0.198 10 false IG 0.958,1.385 1.146,1.583 0.188,0.198 10 false S

Disconnect the transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (IG) - 7 (S) Shift lever in S, "+" or "-" Below 1 Ω
3 (IG) - 7 (S) Shift lever not in S, "+" or "-" 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Transmission Control Switch)



OK

6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH, TRANSMISSION CONTROL SWITCH - ECM)

NG

REPLACE TRANSMISSION CONTROL SWITCH (LOWER SHIFT LEVER ASSEMBLY)

6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH, TRANSMISSION CONTROL SWITCH - ECM)
a.
U165268E03
2.479,1.958 2.156,1.208 true 0.781,4.365 0.667,3.26 true 2.042,4.063 0.74,3.177 true 1.719,4.365 0.75,3.271 true 0.313,4.021 0.656,3.177 true 1.448,2.479 1.823,2.708 0.375,0.229 10 false C45 0.104,0.031 0.302,0.229 0.198,0.198 10 false *a 2.313,2 2.885,2.229 0.573,0.229 10 false 27 (S) 1.698,0.427 2.073,0.656 0.375,0.229 10 false A38 0.625,4.396 1.156,4.594 0.531,0.198 10 false 49 (D) 1.875,4.073 2.417,4.271 0.542,0.198 10 false 27 (P) 1.552,4.406 2.083,4.604 0.531,0.198 10 false 50 (N) 0.083,4.083 0.604,4.281 0.521,0.198 10 false 26 (R)

Disconnect the ECM connectors.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C45-27 (P) - Body ground
·

Engine switch on (IG)

·

Shift lever in P


11 to 14 V
C45-26 (R) - Body ground
·

Engine switch on (IG)

·

Shift lever in R


11 to 14 V*
C45-50 (N) - Body ground
·

Engine switch on (IG)

·

Shift lever in N


11 to 14 V
C45-49 (D) - Body ground
·

Engine switch on (IG)

·

Shift lever in D, S, "+" or "-"


11 to 14 V
A38-27 (S) - Body ground
·

Engine switch on (IG)

·

Shift lever in S, "+" or "-"


11 to 14 V
C45-27 (P) - Body ground
·

Engine switch on (IG)

·

Shift lever not in P


Below 1 V
C45-26 (R) - Body ground
·

Engine switch on (IG)

·

Shift lever not in R


Below 1 V
C45-50 (N) - Body ground
·

Engine switch on (IG)

·

Shift lever not in N


Below 1 V
C45-49 (D) - Body ground
·

Engine switch on (IG)

·

Shift lever not in D, S, "+" or "-"


Below 1 V
A38-27 (S) - Body ground
·

Engine switch on (IG)

·

Shift lever not in S, "+" or "-"


Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to ECM)

HINT:

*: The voltage will drop slightly due to lighting up of the backup light.




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C24-4 (B) - C45-48 (NSW) Always Below 1 Ω
C24-4 (B) - Body ground Always 10 kΩ or higher
C45-48 (NSW) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR