Home › Engine / Hybrid System › 3UR-FE (ENGINE CONTROL) › SFI SYSTEM(w/ Secondary Air Injection System) › from 2017.08
RM2660E _51 Engine / Hybrid System _052775 3UR-FE ENGINE CONTROL _0327320 SFI SYSTEM(w/ Secondary Air Injection System) C

3UR-FE ENGINE CONTROL  SFI SYSTEM(w/ Secondary Air Injection System)  P0010  Camshaft Position "A" Actuator Circuit (Bank 1)  P0020  Camshaft Position "A" Actuator Circuit (Bank 2)  


DESCRIPTION

·

This DTC is designed to detect opens or shorts in the camshaft oil control valve (OCV) circuit. If the OCV duty-cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.

·

The VVT (variable valve timing) system adjusts the intake valve timing to improve the driveability. The engine oil pressure turns the camshaft actuator to adjust the valve timing. The OCV is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time to the solenoid (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.


A130637E07
4.655,0.815 6.376,1.027 1.721,0.211 10 VVT Sensor (CMP Sensor) 4.655,1.325 5.481,1.486 0.825,0.161 10 CKP Sensor 0.072,0.015 1.622,0.268 1.550,0.253 12 VVT System: 2.337,1.96 3.613,2.135 1.277,0.174 10 Target Valve Timing 2.337,1.288 3.613,1.462 1.277,0.174 10 Actual Valve Timing 2.687,2.696 3.401,2.870 0.714,0.174 10 Correction 2.826,3.204 3.227,3.379 0.402,0.174 10 ECM 1.602,3.748 3.762,3.922 2.160,0.174 10 Camshaft Oil Control Valve (OCV) 0.17,2.69 0.864,2.865 0.695,0.174 10 Duty-cycle 4.655,1.828 5.494,1.981 0.839,0.154 10 MAF Sensor 4.655,2.854 5.453,3.043 0.797,0.188 10 ECT Sensor 4.655,2.344 5.022,2.512 0.367,0.167 10 TPS 4.655,3.353 5.008,3.507 0.353,0.154 10 VSS 0.317,4.27 1.686,4.474 1.369,0.205 10 Engine Oil Pressure 3.663,4.217 4.889,4.401 1.225,0.184 10 Camshaft Actuator 3.887,4.918 4.988,5.101 1.100,0.184 10 Intake Camshaft 2.566,4.571 2.846,4.275 2.846,4.275 3.611,4.275 false 3.181,4.782 3.323,5.009 3.323,5.009 3.856,5.009 false

DTC Code DTC Detection Condition Trouble Area
P0010 An open or short in the Camshaft Oil Control Valve (OCV) for intake side (for Bank 1) circuit (1 trip detection logic).
·

Open or short in Camshaft Oil Control Valve (OCV) (for intake side of Bank 1) circuit

·

OCV (for intake side of Bank 1)

·

ECM


P0020 An open or short in the OCV for intake side (for Bank 2) circuit (1 trip detection logic).
·

Open or short in OCV (for intake side of Bank 2) circuit

·

OCV (for intake side of Bank 2)

·

ECM



HINT:

This DTC relates to the Camshaft Oil Control Valve (OCV).


MONITOR DESCRIPTION

This DTC is designed to detect opens or shorts in the camshaft oil control valve (OCV) circuit. If the OCV duty-cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

A162759E30
5.896,4.302 6.385,4.49 0.49,0.188 10 false ECM 0.24,1.813 2.615,2 2.375,0.188 10 false OCV for Intake Camshaft (for Bank 1) 1.479,0.521 1.844,0.781 0.365,0.26 10 false 1 1.479,1.24 1.771,1.458 0.292,0.219 10 false 2 1.469,2.469 1.833,2.729 0.365,0.26 10 false 1 1.469,3.208 1.76,3.427 0.292,0.219 10 false 2 5.229,0.51 5.5,0.74 0.271,0.229 10 false 6 5.229,1.26 5.5,1.49 0.271,0.229 10 false 5 5.229,3.229 5.5,3.458 0.271,0.229 10 false 3 5.229,2.469 5.5,2.698 0.271,0.229 10 false 4 5.417,0.51 6.021,0.802 0.604,0.292 10 false OC1+ 5.427,1.24 6.021,1.51 0.594,0.271 10 false OC1- 5.417,2.469 6.135,2.698 0.719,0.229 10 false OC2+ 5.427,3.229 6.167,3.49 0.74,0.26 10 false OC2- 5.896,4.125 6.26,4.396 0.365,0.271 10 false C45 0.26,1.656 0.573,1.844 0.313,0.188 10 false C27 0.26,3.604 0.573,3.792 0.313,0.188 10 false C28 0.25,3.76 2.594,4.021 2.344,0.26 10 false OCV for Intake Camshaft (for Bank 2)

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.



PROCEDURE

1.CHECK DTC

b.

Turn the engine switch off.


c.

Allow the engine to idle and check DTC.


d.

Check that P0010 or P0020 is not output.

OK:

P0010 or P0020 is not output.




OK

NG

2.INSPECT CAMSHAFT OIL CONTROL VALVE ASSEMBLY
2.INSPECT CAMSHAFT OIL CONTROL VALVE ASSEMBLY
a.
A160397E02
0.059,0 2.561,0.350 2.502,0.350 10 Component without harness connected: (Oil Control Valve)

Disconnect the C27 or C28 camshaft oil control valve (OCV) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 6.9 to 7.9 Ω




OK

3.CHECK HARNESS AND CONNECTOR (OCV - ECM)

NG

REPLACE CAMSHAFT OIL CONTROL VALVE ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (OCV - ECM)
a.

Disconnect the C27 or C28 OCV connector.


b.

Disconnect the C45 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C27-1 - C45-6 (OC1+) Always Below 1 Ω
C28-1 - C45-4 (OC2+) Always Below 1 Ω
C27-2 - C45-5 (OC1-) Always Below 1 Ω
C28-2 - C45-3 (OC2-) Always Below 1 Ω
C27-1 or C45-6 (OC1+) - Body ground Always 10 kΩ or higher
C28-1 or C45-4 (OC2+) - Body ground Always 10 kΩ or higher
C27-2 or C45-5 (OC1-) - Body ground Always 10 kΩ or higher
C28-2 or C45-3 (OC2-) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR