Home › Engine / Hybrid System › 3UR-FE (ENGINE CONTROL) › SFI SYSTEM(w/ Secondary Air Injection System) › from 2017.08
RM2660E _51 Engine / Hybrid System _052775 3UR-FE ENGINE CONTROL _0327320 SFI SYSTEM(w/ Secondary Air Injection System) C

3UR-FE ENGINE CONTROL  SFI SYSTEM(w/ Secondary Air Injection System)  P0137  Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2)  P0157  Oxygen Sensor Circuit Low Voltage (Bank 2 Sensor 2)  


DESCRIPTION

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a TWC is used. For the most efficient use of the TWC, the air-fuel ratio must be precisely controlled so that it is always close to the stoichiometric air-fuel ratio. For the purpose of helping the ECM to deliver accurate air-fuel ratio control, a Heated Oxygen (HO2) sensor is used.

The HO2 sensor is located behind the TWC, and detects the oxygen concentration in the exhaust gas. Since the sensor is integrated with the heater that heats the sensing portion, it is possible to detect the oxygen concentration even when the intake air volume is low (the exhaust gas temperature is low).

When the air-fuel ratio becomes lean, the oxygen concentration in the exhaust gas is rich. The HO2 sensor informs the ECM that the post-TWC air-fuel ratio is lean (low voltage, i.e. below 0.45 V).

Conversely, when the air-fuel ratio is richer than the stoichiometric air-fuel ratio, the oxygen concentration in the exhaust gas becomes lean. The HO2 sensor informs the ECM that the post-TWC air-fuel ratio is rich (high voltage, i.e. higher than 0.45 V). The HO2 sensor has the property of changing its output voltage drastically when the air-fuel ratio is close to the stoichiometric level.

The ECM uses the supplementary information from the HO2 sensor to determine whether the air-fuel ratio after the TWC is rich or lean, and adjusts the fuel injection time accordingly. Thus, if the HO2 sensor is working improperly due to internal malfunctions, the ECM is unable to compensate for deviations in the primary air-fuel ratio control.

A115539E07
2.979,1.229 3.292,0.844 false 2.688,1.792 3.302,1.792 true 2.594,2.417 3.25,2.385 true 2.677,2.698 3.26,2.833 false 1.094,2.917 1.333,2.917 false 2.667,1.458 2.667,1.531 false 2.729,1.646 3.302,1.271 3.302,1.271 2.667,1.49 true 1.448,0.771 2.458,0.969 1.01,0.198 10 false Atmospheric Air 3.354,0.74 4.094,0.938 0.74,0.198 10 false Housing 3.365,1.188 4.667,1.406 1.302,0.219 10 false Platinum Electrode 3.958,0.885 4.927,1.083 0.969,0.198 10 false Output Voltage 5.01,0.927 6.396,1.125 1.385,0.198 10 false Ideal Air-fuel Mixture 2.01,3.167 2.906,3.365 0.896,0.198 10 false Exhaust Gas 3.344,1.698 4.521,2.083 1.177,0.385 10 false Solid Electrolyte (Zirconia Element) 3.292,2.76 4.49,2.958 1.198,0.198 10 false Coating (Ceramic) 3.323,2.281 3.802,2.479 0.479,0.198 10 false Heater 1.365,2.823 1.802,3.031 0.438,0.208 10 false Cover 4.792,2.927 7.094,3.125 2.302,0.198 10 false Richer - Air-fuel Ratio - Leaner

DTC Code DTC Detection Condition Trouble Area
P0137
P0157

Low voltage (open):

During active air-fuel ratio control, the following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):


(a)

The HO2 sensor voltage output is below 0.21 V.

(b)

The target air-fuel ratio is rich.



·

Open in HO2 sensor (for Bank 1, 2) circuit

·

HO2 sensor (for Bank 1, 2)

·

HO2 sensor heater (for Bank 1, 2)

·

No. 2 integration relay

·

Gas leakage from exhaust system



MONITOR DESCRIPTION

Active Air-Fuel Ratio Control

The ECM usually performs air-fuel ratio feedback control so that the Air Fuel ratio (A/F) sensor output indicates a near stoichiometric air-fuel ratio. This vehicle includes active air-fuel ratio control in addition to regular air-fuel ratio control. The ECM performs active air-fuel ratio control to detect any deterioration in the Three-Way Catalytic Converter (TWC) and Heated Oxygen (HO2) sensor malfunctions (refer to the diagram below).

Active air-fuel ratio control is performed for approximately 15 to 20 seconds while driving with a warm engine. During active air-fuel ratio control, the air-fuel ratio is forcibly regulated to become lean or rich by the ECM. If the ECM detects a malfunction, a DTC is stored.



Open or Short in Heated Oxygen (HO2) Sensor Circuit (DTC P0137 and P0157)

During active air-fuel ratio control, the ECM calculates the Oxygen Storage Capacity (OSC)* of the Three-Way Catalytic Converter (TWC) by forcibly regulating the air-fuel ratio to become rich or lean. If the HO2 sensor has an open or short, or the voltage output of the sensor decreases significantly, the OSC indicates an extraordinarily high value. Even if the ECM attempts to continue regulating the air-fuel ratio to become rich or lean, the HO2 sensor output does not change.

While performing active air-fuel ratio control, when the target air-fuel ratio is rich and the HO2 sensor voltage output is 0.21 V or less (lean), the ECM interprets this as an abnormally low sensor output voltage and stores DTC P0137 or P0157.

*: The TWC has the capability to store oxygen. The OSC and the emission purification capacity of the TWC are mutually related. The ECM determines whether the catalyst has deteriorated based on the calculated OSC value.

A244503E02
4.635,1.75 4.365,1.615 true 5.969,2.417 6.156,2.083 false 6,3.188 6.188,3.396 false 5.125,2.104 5.25,1.531 true 0.083,0.073 3.24,0.302 3.156,0.229 12 false HO2 SENSOR CIRCUIT LOW VOLTAGE 0.083,0.51 1.854,0.719 1.771,0.208 10 false (P0137 and P0157: OPEN) 1.104,1.281 3.063,1.479 1.958,0.198 10 false Active air-fuel ratio control 1.104,2.698 2.594,2.896 1.49,0.198 10 false HO2 sensor voltage 1.125,1.771 2.594,1.969 1.469,0.198 10 false Target air-fuel ratio 2.521,1.708 3.625,2.073 1.104,0.365 10 false Stoichiometric Air-fuel Ratio 3.229,1.365 3.49,1.563 0.26,0.198 10 false Off 3.01,2.927 3.469,3.125 0.458,0.198 10 false 0.21 V 4.646,0.323 5.948,0.521 1.302,0.198 10 false 15 to 20 seconds 4.521,1.375 5.281,1.573 0.76,0.198 10 false Operation 3.896,1.531 4.458,1.729 0.563,0.198 10 false Normal 5.313,1.417 6.052,1.615 0.74,0.198 10 false Abnormal 6.25,3.333 6.99,3.531 0.74,0.198 10 false Abnormal 6.198,1.958 6.76,2.156 0.563,0.198 10 false Normal 4.792,2.125 5.156,2.323 0.365,0.198 10 false Rich


WIRING DIAGRAM

A372447E03
5.823,0.583 6.219,0.74 0.396,0.156 10 false HT1B 5.823,3.198 6.219,3.354 0.396,0.156 10 false HT2B 4.448,3.198 4.844,3.354 0.396,0.156 10 false HT2B 5.479,0.667 5.76,0.823 0.281,0.156 10 false C45 5.479,1.115 5.76,1.271 0.281,0.156 10 false C45 5.479,1.542 5.76,1.698 0.281,0.156 10 false C45 5.479,3.292 5.76,3.448 0.281,0.156 10 false C45 5.479,3.75 5.76,3.906 0.281,0.156 10 false C45 5.479,4.177 5.76,4.333 0.281,0.156 10 false C45 5.49,5.365 5.771,5.521 0.281,0.156 10 false A38 5.833,1.021 6.24,1.177 0.406,0.156 10 false OX1B 4.448,1.021 4.854,1.177 0.406,0.156 10 false OX1B 5.833,3.656 6.24,3.813 0.406,0.156 10 false OX2B 4.448,3.656 4.854,3.813 0.406,0.156 10 false OX2B 5.833,1.448 6.229,1.604 0.396,0.156 10 false EX1B 5.833,4.063 6.229,4.219 0.396,0.156 10 false EX2B 5.844,5.281 6.26,5.438 0.417,0.156 10 false MREL 6.135,6.396 6.479,6.552 0.344,0.156 10 false ECM 5.531,0.479 5.76,0.646 0.229,0.167 10 false 21 5.531,0.938 5.792,1.146 0.26,0.208 10 false 96 5.531,1.365 5.802,1.531 0.271,0.167 10 false 95 5.531,3.135 5.729,3.292 0.198,0.156 10 false 44 5.5,3.583 5.781,3.74 0.281,0.156 10 false 119 5.5,4 5.781,4.156 0.281,0.156 10 false 118 5.573,5.188 5.76,5.344 0.188,0.156 10 false 6 3.698,1.823 4.063,2 0.365,0.177 10 false C20 3.698,1.979 4.927,2.313 1.229,0.333 10 false Heated Oxygen Sensor (for Bank 1) 3.688,4.448 3.979,4.604 0.292,0.156 10 false C56 3.688,4.604 4.927,4.938 1.24,0.333 10 false Heated Oxygen Sensor (for Bank 2) 4.896,0.573 5.01,0.729 0.115,0.156 10 false 1 3.677,0.573 3.792,0.729 0.115,0.156 10 false 2 4.896,1.021 5.021,1.167 0.125,0.146 10 false 3 4.896,1.458 5.021,1.615 0.125,0.156 10 false 4 4.906,3.198 5.021,3.354 0.115,0.156 10 false 1 3.656,3.198 3.771,3.354 0.115,0.156 10 false 2 4.906,3.656 5.031,3.802 0.125,0.146 10 false 3 4.906,4.083 5.031,4.24 0.125,0.156 10 false 4 3.854,0.573 4.052,0.729 0.198,0.156 10 false +B 3.833,3.198 4.031,3.354 0.198,0.156 10 false +B 4.448,0.573 4.844,0.729 0.396,0.156 10 false HT1B 4.625,1.448 4.823,1.604 0.198,0.156 10 false E1 4.635,4.083 4.833,4.24 0.198,0.156 10 false E1 3.875,6.125 4.615,6.292 0.74,0.167 10 false *: Shielded 2.042,0.823 2.698,0.979 0.656,0.156 10 false EFI NO. 2 1.24,1.729 2.927,2.031 1.688,0.302 10 false No. 2 Integration Relay 1.302,1.385 2.417,1.625 1.115,0.24 10 false EFI MAIN NO. 1 0.667,0.802 1.438,1.177 0.771,0.375 10 false EFI MAIN NO. 1 2.75,0.469 2.896,0.667 0.146,0.198 10 false 1 2.792,1.333 2.906,1.49 0.115,0.156 10 false 8 0.948,1.333 1.094,1.542 0.146,0.208 10 false 4 0.448,1.333 0.563,1.49 0.115,0.156 10 false 1 2.698,0.656 2.948,0.844 0.25,0.188 10 false 1S 2.656,1.51 2.938,1.688 0.281,0.177 10 false 1S 0.969,1.5 1.25,1.698 0.281,0.198 10 false 1S 0.49,1.51 0.792,1.708 0.302,0.198 10 false 1X 0.865,5.344 1.417,5.552 0.552,0.208 10 false Battery 5.146,1.802 5.271,1.938 0.125,0.135 10 false * 5.125,4.427 5.25,4.563 0.125,0.135 10 false * 0.688,3.417 1.167,3.594 0.479,0.177 10 false P/I-B

CONFIRMATION DRIVING PATTERN

HINT:
·

This confirmation driving pattern is used in the "Perform Confirmation Driving Pattern" procedure of the following diagnostic troubleshooting procedure.

·

Performing this confirmation driving pattern will activate the Heated Oxygen (HO2) sensor monitor (the catalyst monitor is performed simultaneously). This is very useful for verifying the completion of a repair.



NOTICE:

This test will not be completed if the vehicle is driven under absolutely constant speed conditions such as with cruise control activated.


A172863E04
0.687,0.396 1.641,0.599 0.954,0.203 10 Vehicle Speed 0.464,2.592 1.689,2.795 1.225,0.203 10 Engine Switch off 4.778,2.764 5.278,2.967 0.500,0.203 10 Time 1.265,2.232 1.658,2.435 0.393,0.203 10 Idling 0.205,0.873 1.637,1.440 1.432,0.567 10 Between 90 km/h and 110 km/h (56 mph and 68 mph) 2.35,2.104 2.578,2.307 0.228,0.203 10 (A) 3.852,0.719 4.079,0.922 0.228,0.203 10 (B) 2.189,2.796 2.818,2.999 0.629,0.203 10 Warm Up 3.422,2.882 4.152,3.085 0.730,0.203 10 10 minutes 1.56,3.239 6.017,3.442 4.457,0.203 10 (Note: Even if vehicle stops during driving pattern, test can be resumed) 4.937,0.115 6.180,0.317 1.244,0.202 10 NOTICE: 4.937,0.29 7.044,1.156 2.107,0.866 10 This test will not be completed if the vehicle is driven at absolutely constant speed, such as with cruise control activated.

1.

Connect the intelligent tester to the DLC3.

2.

Turn the engine switch on (IG).

3.

Turn the tester on.

4.

Enter the following menus: Powertrain / Engine and ECT / DTC / Clear.

5.

Clear DTCs.

6.

Switch the ECM from normal mode to check mode

7.

Enter the following menus: Powertrain / Engine and ECT / Data List / O2S (A/FS) Monitor.

8.

Check that the item O2S (A/FS) Monitor displays Incmpl (Incomplete).

9.

Start the engine and warm it up. (Proceed to "A")

10.

Drive the vehicle at between 90 km/h and 110 km/h (56 mph and 68 mph) for at least 10 minutes. (Proceed to "B")

11.

Note the state of the Data List items. Those items will change to Compl (Complete) as the O2 Sensor monitor operates.

12.

On the tester, enter the following menus: Powertrain / Engine and ECT / DTC / Pending and check if any DTCs (any pending DTCs) are output.


CAUTION / NOTICE / HINT

HINT:

Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F sensor function provided in the Active Test. The Control the Injection Volume for A/F sensor function can help to determine whether the Air Fuel ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the Control the Injection Volume for A/F sensor operation using the intelligent tester.

1.

Connect the tester to the DLC3.

2.

Start the engine and turn the tester on.

3.

Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.

4.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.

5.

Perform the Active Test operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).

6.

Monitor the output voltages of the A/F and HO2 sensors (AFS B1 S1 and O2S B1 S2 or AFS B2 S1 and O2S B2 S2) displayed on the tester.



HINT:
·

The Control the Injection Volume for A/F sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.



Display Item (Sensor) Injection Volume Status Voltage
AFS B1 S1 or AFS B2 S1
(A/F)
+25% Rich Below 3.1 V
AFS B1 S1 or AFS B2 S1
(A/F)
-12.5% Lean Higher than 3.4 V
O2S B1 S2 or O2S B2 S2
(HO2)
+25% Rich Higher than 0.55 V
O2S B1 S2 or O2S B2 S2
(HO2)
-12.5% Lean Below 0.4 V

NOTICE:

The Air Fuel ratio (A/F) sensor has an output delay of a few seconds and the Heated Oxygen (HO2) sensor has a maximum output delay of approximately 20 seconds.


A283583E51
5.792,3.594 7.115,3.865 1.323,0.271 10 false - Air fuel ratio sensor 3.823,4.927 4.531,5.104 0.708,0.177 8 false Below 0.4 V 3.208,4.396 4.333,4.615 1.125,0.219 10 false Output Voltage 3.25,3.365 4.542,3.615 1.292,0.25 10 false Injection Volume 3.229,1.292 4.521,1.542 1.292,0.25 10 false Injection Volume 3.24,2.313 4.333,2.521 1.094,0.208 10 false Output Voltage 0.625,1.292 1.917,1.542 1.292,0.25 10 false Injection Volume 0.625,3.365 1.917,3.615 1.292,0.25 10 false Injection Volume 0.594,5.438 1.885,5.688 1.292,0.25 10 false Injection Volume 0.604,7.49 1.896,7.74 1.292,0.25 10 false Injection Volume 3.25,7.49 4.542,7.74 1.292,0.25 10 false Injection Volume 3.25,5.438 4.542,5.688 1.292,0.25 10 false Injection Volume 0.635,2.302 1.823,2.51 1.188,0.208 10 false Output Voltage 0.625,4.396 1.792,4.646 1.167,0.25 10 false Output Voltage 0.552,6.479 1.719,6.729 1.167,0.25 10 false Output Voltage 0.573,8.563 1.74,8.813 1.167,0.25 10 false Output Voltage 3.24,8.563 4.406,8.813 1.167,0.25 10 false Output Voltage 3.25,6.479 4.417,6.729 1.167,0.25 10 false Output Voltage 3.51,4.698 4.542,4.885 1.031,0.188 8 false Higher than 0.55 V 0.927,2.646 1.958,2.833 1.031,0.188 8 false Higher than 3.4 V 1.177,2.885 1.927,3.073 0.75,0.188 8 false Below 3.1 V 1.552,1.604 2,1.792 0.448,0.188 8 false +25% 1.49,1.833 1.917,2.01 0.427,0.177 8 false -12.5% 3.5,2.604 4.531,2.792 1.031,0.188 8 false Higher than 0.55 V 3.813,2.844 4.521,3.021 0.708,0.177 8 false Below 0.4 V 0.844,4.802 2.042,5.052 1.198,0.25 8 false Almost no reaction 0.854,8.938 2.052,9.188 1.198,0.25 8 false Almost no reaction 3.5,8.938 4.698,9.188 1.198,0.25 8 false Almost no reaction 3.49,6.865 4.688,7.115 1.198,0.25 8 false Almost no reaction 0.917,6.771 1.948,6.958 1.031,0.188 8 false Higher than 3.4 V 1.167,7.021 1.917,7.208 0.75,0.188 8 false Below 3.1 V 0.24,2.083 0.396,2.281 0.156,0.198 10 false 1 0.24,4.25 0.396,4.448 0.156,0.198 10 false 2 0.25,6.333 0.406,6.531 0.156,0.198 10 false 3 0.24,8.417 0.396,8.615 0.156,0.198 10 false 4 0.115,0.49 0.49,0.719 0.375,0.229 10 false Case 0.813,0.448 2.844,0.844 2.031,0.396 10 false Air Fuel Ratio Sensor (Sensor 1) Output Voltage 3.375,0.469 5.531,0.875 2.156,0.406 10 false Heated Oxygen Sensor (Sensor 2) Output Voltage 5.938,0.469 6.979,0.885 1.042,0.417 10 false Main Suspected Trouble Area 6.396,2.115 6.552,2.313 0.156,0.198 10 false - 5.802,4 7.125,4.438 1.323,0.438 10 false - Air fuel ratio sensor heater 5.802,4.635 7.125,5.073 1.323,0.438 10 false - Air fuel ratio sensor circuit 5.844,5.51 6.896,5.885 1.052,0.375 10 false - Heated oxygen sensor 5.844,6.135 6.885,6.563 1.042,0.427 10 false - Heated oxygen sensor heater 5.844,6.75 6.885,7.188 1.042,0.438 10 false - Heated oxygen sensor circuit 5.823,7.51 6.708,7.917 0.885,0.406 10 false - Fuel injector assembly 5.813,8.063 6.969,8.396 1.156,0.333 10 false - Fuel pressure 5.802,8.375 7.094,9.083 1.292,0.708 10 false - Gas leakage from exhaust system (Air fuel ratio extremely rich or lean) 2.552,2.75 3,2.938 0.448,0.188 8 false OK 2.5,4.719 2.948,4.906 0.448,0.188 8 false NG 2.552,6.865 3,7.052 0.448,0.188 8 false OK 2.5,8.844 2.948,9.031 0.448,0.188 8 false NG 5.167,2.708 5.615,2.896 0.448,0.188 8 false OK 5.167,4.813 5.615,5 0.448,0.188 8 false OK 5.135,8.854 5.583,9.042 0.448,0.188 8 false NG 5.135,6.771 5.583,6.958 0.448,0.188 8 false NG 1.5,3.677 1.948,3.865 0.448,0.188 8 false +25% 4.083,1.594 4.531,1.781 0.448,0.188 8 false +25% 4.073,3.667 4.521,3.854 0.448,0.188 8 false +25% 1.427,3.875 1.854,4.052 0.427,0.177 8 false -12.5% 4.021,1.823 4.448,2 0.427,0.177 8 false -12.5% 4.021,3.896 4.448,4.073 0.427,0.177 8 false -12.5% 1.469,5.75 1.917,5.938 0.448,0.188 8 false +25% 1.458,7.771 1.906,7.958 0.448,0.188 8 false +25% 4.094,7.792 4.542,7.979 0.448,0.188 8 false +25% 4.156,5.729 4.604,5.917 0.448,0.188 8 false +25% 1.406,5.948 1.833,6.125 0.427,0.177 8 false -12.5% 1.396,8.01 1.823,8.188 0.427,0.177 8 false -12.5% 4.031,8.021 4.458,8.198 0.427,0.177 8 false -12.5% 4.083,5.938 4.51,6.115 0.427,0.177 8 false -12.5%

·

Following the Control the Injection Volume for A/F sensor procedure enables technicians to check and graph the voltage outputs of both the A/F and HO2 sensors.

·

To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume / All Data / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.


HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.



PROCEDURE

1.READ OUTPUT DTC
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.


d.

Read DTCs.

Result
Result Proceed to
P0137 or P0157 is output A
P0137 or P0157 and other DTCs are output B



A

2.CHECK FOR EXHAUST GAS LEAKAGE

B

2.CHECK FOR EXHAUST GAS LEAKAGE
OK:

No gas leakage.



OK

3.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

NG

REPAIR OR REPLACE EXHAUST GAS LEAKAGE POINT

3.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

OK

4.INSPECT NO. 2 INTEGRATION RELAY (EFI MAIN NO. 1)

NG

4.INSPECT NO. 2 INTEGRATION RELAY (EFI MAIN NO. 1)
a.

Remove the No. 2 integration relay from the engine room relay block.


b.

Inspect the No. 2 integration relay (EFI MAIN NO. 1) (See page Engine / Hybrid System>3UR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).



OK

5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

REPLACE NO. 2 INTEGRATION RELAY

5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the C20 or C56 HO2 sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C20-2 (+B) - Body ground Engine switch on (IG) 11 to 14 V
C56-2 (+B) - Body ground Engine switch on (IG) 11 to 14 V



c.

Turn the engine switch off.


d.

Disconnect the C45 ECM connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C20-1 (HT1B) - C45-21 (HT1B) Always Below 1 Ω
C20-3 (OX1B) - C45-96 (OX1B) Always Below 1 Ω
C20-4 (E1) - C45-95 (EX1B) Always Below 1 Ω
C56-1 (HT2B) - C45-44 (HT2B) Always Below 1 Ω
C56-3 (OX2B) - C45-119 (OX2B) Always Below 1 Ω
C56-4 (E1) - C45-118 (EX2B) Always Below 1 Ω
C20-1 (HT1B) or C45-21 (HT1B) - Body ground Always 10 kΩ or higher
C20-3 (OX1B) or C45-96 (OX1B) - Body ground Always 10 kΩ or higher
C56-1 (HT2B) or C45-44 (HT2B) - Body ground Always 10 kΩ or higher
C56-3 (OX2B) or C45-119 (OX2B) - Body ground Always 10 kΩ or higher



A164717E30
0.083,0.073 2.063,0.323 1.979,0.25 10 false Reference (System Diagram): 2.833,1.188 3.51,1.365 0.677,0.177 10 false EFI NO. 2 1.125,1.229 1.792,1.719 0.667,0.49 10 false EFI MAIN NO. 1 1.021,3.333 1.5,3.51 0.479,0.177 10 false Ground 3.833,2.167 4.927,2.406 1.094,0.24 10 false HO2 Sensor 3.552,0.938 3.781,1.115 0.229,0.177 10 false +B 4.323,0.948 4.698,1.125 0.375,0.177 10 false HT1B 3.563,1.5 3.823,1.677 0.26,0.177 10 false E1 4.344,1.49 4.771,1.677 0.427,0.188 10 false OX1B 5.385,1.479 5.813,1.656 0.427,0.177 10 false OX1B 5.396,2.271 5.823,2.448 0.427,0.177 10 false EX1B 3.958,1.208 4.417,1.385 0.458,0.177 10 false Heater 3.927,1.844 4.406,2.042 0.479,0.198 10 false Sensor 6.031,3.458 6.417,3.646 0.385,0.188 10 false ECM 5.385,0.938 5.802,1.125 0.417,0.188 10 false HT1B 5.385,2.854 5.833,3.042 0.448,0.188 10 false MREL 0.521,1.063 1.167,1.469 0.646,0.406 10 false from Battery 2.115,2.688 2.781,3.177 0.667,0.49 10 false EFI MAIN NO. 1


OK

6.REPLACE HEATED OXYGEN SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE HEATED OXYGEN SENSOR
a.


NEXT

7.CHECK WHETHER DTC OUTPUT RECURS
7.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


e.

Input DTCs: P0137 or P0157.


f.

Check that DTC MONITOR is NORMAL. If DTC MONITOR is INCOMPLETE, perform the drive pattern adding the vehicle speed.

Result
Result Proceed to
NORMAL
(No DTC output)
A
ABNORMAL
(P0137 or P0157 detected)
B



A

END

B