The exhaust camshaft Variable Valve Timing (VVT) sensor (EV1, 2 signal) consists of a magnet and MRE (Magnetic Resistance Element).
The exhaust camshaft has a sensor plate with 3 teeth on its outer circumference. When the exhaust camshaft rotates, changes occur in the air gaps between the 3 teeth and MRE, which affects the magnet. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the exhaust camshaft rotation data into pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0365
P0390 |
When either condition below is met:
·
The input voltage to the ECM remains at below 0.3 V or higher than 4.7 V for more than 4 seconds when 2 or more seconds have elapsed after turning the engine switch on (IG) (1 trip detection logic). ·
No VVT sensor signal is sent to the ECM during cranking (1 trip detection logic). |
·
Open or short in VVT sensor (for exhaust side) circuit ·
VVT sensor (for exhaust side) ·
Exhaust camshaft ·
Jumped tooth of timing chain ·
ECM |
| P0367
P0392 |
The output voltage of the VVT sensor is below 0.3 V for 4 seconds (1 trip detection logic). | ·
Open or short in VVT sensor (for exhaust side) circuit ·
VVT sensor (for exhaust side) ·
Exhaust camshaft ·
Jumped tooth of timing chain ·
ECM |
| P0368
P0393 |
The output voltage of the VVT sensor is higher than 4.7 V for 4 seconds (1 trip detection logic). | ·
Open or short in VVT sensor (for exhaust side) circuit ·
VVT sensor (for exhaust side) ·
Exhaust camshaft ·
Jumped tooth of timing chain ·
ECM |
Reference: Inspection using an oscilloscope.
| Tester Connection | Tool Setting | Condition | Specified Condition |
|---|---|---|---|
| C45-66 (NE+) - C45-65 (NE-) | 5 V/DIV.
20 msec./DIV. |
Cranking or idling | The correct waveform is as shown |
| C45-90 (EV1+) - C45-88 (VV1-) | 5 V/DIV.
20 msec./DIV. |
Cranking or idling | The correct waveform is as shown |
| C45-113 (EV2+) - C45-111 (VV2-) | 5 V/DIV.
20 msec./DIV. |
Cranking or idling | The correct waveform is as shown |
EV1+ and EV2+ stand for the VVT sensor (for exhaust side) signal, and NE+ stands for the CKP sensor signal.
If no signal is transmitted by the VVT sensor despite the engine revolving, or the rotations of the camshaft and the crankshaft are not synchronized, the ECM interprets this as a malfunction of the sensor.
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Bank 1 refers to the bank that includes the No. 1 cylinder*.
*: The No. 1 cylinder is the cylinder which is farthest from the transmission.
Bank 2 refers to the bank that does not include the No. 1 cylinder.
Disconnect the C121 or C122 VVT sensor (for exhaust side) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C121-3 (VC2) - Body ground | Engine switch on (IG) | 4.5 to 5.0 V |
| C122-3 (VC2) - Body ground | Engine switch on (IG) | 4.5 to 5.0 V |
OK
NG
Disconnect the C121 or C122 VVT (for exhaust side) sensor connector.
Disconnect the C45 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C121-1 (EX+) - C45-90 (EV1+) | Always | Below 1 Ω |
| C121-2 (EX-) - C45-88 (VV1-) | Always | Below 1 Ω |
| C122-1 (EX+) - C45-113 (EV2+) | Always | Below 1 Ω |
| C122-2 (EX-) - C45-111 (VV2-) | Always | Below 1 Ω |
| C121-1 (EX+) or C45-90 (EV1+) - Body ground | Always | 10 kΩ or higher |
| C121-2 (EX-) or C45-88 (VV1-) - Body ground | Always | 10 kΩ or higher |
| C122-1 (EX+) or C45-113 (EV2+) - Body ground | Always | 10 kΩ or higher |
| C122-2 (EX-) or C45-111 (VV2-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Check the VVT sensor (for exhaust side) installation.
Sensor is installed correctly.
OK
NG
Check the teeth of the camshaft.
Teeth do not have any cracks or deformation.
OK
NG
Replace the VVT sensor (for exhaust side) (See page Engine / Hybrid System>3UR-FE (ENGINE CONTROL)>CAMSHAFT POSITION SENSOR>REMOVAL).
NEXT
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Result | Proceed to |
|---|---|
| No output | A |
| P0365, P0367, P0368, P0390, P0392 or P0393 | B |
If the engine does not start, replace the ECM.
A
B