Home › Engine / Hybrid System › 3UR-FE (ENGINE CONTROL) › SFI SYSTEM(w/ Secondary Air Injection System) › from 2017.08
RM2660E _51 Engine / Hybrid System _052775 3UR-FE ENGINE CONTROL _0327320 SFI SYSTEM(w/ Secondary Air Injection System) C

3UR-FE ENGINE CONTROL  SFI SYSTEM(w/ Secondary Air Injection System)  P2120  Throttle / Pedal Position Sensor / Switch "D" Circuit  P2122  Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input  P2123  Throttle / Pedal Position Sensor / Switch "D" Circuit High Input  P2125  Throttle / Pedal Position Sensor / Switch "E" Circuit  P2127  Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input  P2128  Throttle / Pedal Position Sensor / Switch "E" Circuit High Input  P2138  Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation  


DESCRIPTION

HINT:

This ETCS (Electronic Throttle Control System) does not use a throttle cable.

The APP sensor is mounted on the accelerator pedal bracket and has 2 sensor circuits: VPA (main) and VPA2 (sub). This sensor is a non-contact type and uses Hall-effect elements in order to yield accurate signals even in extreme driving conditions, such as at high speeds as well as very low speeds. The voltage, which is applied to terminals VPA and VPA2 of the ECM, varies between 0.5 V and 4.75 V in proportion to the operating angle of the accelerator pedal (throttle valve). A signal from VPA indicates the actual accelerator pedal opening angle (throttle valve opening angle) and is used for engine control. A signal from VPA2 conveys the status of the VPA circuit and is used to check the APP sensor itself.

The ECM monitors the actual accelerator pedal opening angle (throttle valve opening angle) through the signals from VPA and VPA2, and controls the throttle actuator according to these signals.


A112620E11
0.74,1.392 1.554,1.669 0.813,0.276 10 APP Sensor 1.263,1.669 1.744,1.850 0.480,0.181 10 Magnet 0.339,1.842 0.865,2.023 0.526,0.181 10 IC No. 1 0.311,3.318 0.837,3.499 0.526,0.181 10 IC No. 2 2.067,1.739 2.362,1.921 0.295,0.181 10 VPA 2.067,2.071 2.362,2.252 0.295,0.181 10 EPA 2.067,2.393 2.462,2.574 0.395,0.181 10 VCPA 2.067,2.687 2.439,2.869 0.372,0.181 10 VPA2 2.067,3.005 2.439,3.186 0.372,0.181 10 EPA2 2.067,3.327 2.447,3.508 0.380,0.181 10 VCP2 2.693,1.392 3.018,1.574 0.326,0.181 10 ECM 4.267,1.548 4.423,1.729 0.156,0.181 10 *1 5.864,1.548 6.020,1.729 0.156,0.181 10 *2 3.938,1.842 4.225,2.023 0.287,0.181 10 4.55 3.86,2.047 4.225,2.229 0.365,0.181 10 3.988 3.938,2.253 4.225,2.434 0.287,0.181 10 3.75 3.86,2.458 4.225,2.640 0.365,0.181 10 3.188 3.991,2.823 4.201,3.004 0.210,0.181 10 1.6 3.991,3.042 4.201,3.223 0.210,0.181 10 0.8 4.411,3.346 4.698,3.527 0.287,0.181 10 0.29 4.259,3.596 4.415,3.777 0.156,0.181 10 0 5.784,3.596 6.071,3.777 0.287,0.181 10 15.9 4.682,3.587 5.606,3.827 0.924,0.239 10 Usable Range 4.369,4.054 6.794,4.257 2.424,0.202 10 Accelerator Pedal Turning Angle (°) 0.239,5.18 2.518,5.361 2.279,0.181 10 *1: Accelerator Pedal Fully Released 0.239,5.488 2.626,5.653 2.387,0.165 10 *2: Accelerator Pedal Fully Depressed 4.355,2.014 4.234,1.93 false 4.346,2.182 4.234,2.126 false 4.346,2.228 4.234,2.322 false 4.346,2.397 4.234,2.518 false 4.346,2.901 4.215,2.901 false 4.355,3.116 4.206,3.116 false 0.867,3.491 1.347,3.672 0.480,0.181 10 Magnet 0.843,2.878 0.554,3.289 false 0.965,3.195 1.049,3.475 false 0.927,2.504 0.862,1.934 false 1.067,2.205 1.245,1.729 false 1.871,0.851 3.925,1.127 2.054,0.276 10 APP Sensor Output Voltage (V) 4.355,1.841 3.869,0.944 false

DTC Code DTC Detection Condition Trouble Area
P2120 VPA fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic).
·

APP sensor


·

ECM


P2122 VPA is 0.4 V or less for 0.5 seconds or more when the accelerator pedal is fully released (1 trip detection logic).
·

APP sensor


·

Open in VCP1 circuit


·

Open or ground short in VPA circuit


·

ECM


P2123 VPA is 4.8 V or higher for 2.0 seconds or more (1 trip detection logic).
·

APP sensor


·

Open in EPA circuit


·

ECM


P2125 VPA2 fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic).
·

APP sensor


·

ECM


P2127 VPA2 is 1.2 V or less for 0.5 seconds or more when the accelerator pedal is fully released (1 trip detection logic).
·

APP sensor


·

Open in VCP2 circuit


·

Open or ground short in VPA2 circuit


·

ECM


P2128 Conditions (a) and (b) continue for 2.0 seconds or more (1 trip detection logic):
(a) VPA2 is 4.8 V or higher.
(b) VPA is between 0.4 V and 3.45 V.
·

APP sensor


·

Open in EPA2 circuit


·

ECM


P2138 Condition (a) or (b) continues for 2.0 seconds or more (1 trip detection logic):
(a) The difference between VPA and VPA2 is 0.02 V or less.
(b) VPA is 0.4 V or less and VPA2 is 1.2 V or less.
·

Short between VPA and VPA2 circuits


·

APP sensor


·

ECM



HINT:

When any of these DTCs is output, check the APP sensor voltage by entering the following menus: Powertrain / Engine and ECT / Data List / ETCS / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.

Trouble Area Accel Sensor Out No. 1
When AP Released
Accel Sensor Out No. 2
When AP Released
Accel Sensor Out No. 1
When AP Depressed
Accel Sensor Out No. 2
When AP Depressed
VCP circuit open 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V
Open or ground short in VPA circuit 0 to 0.2 V 1.2 to 2.0 V 0 to 0.2 V 3.4 to 4.75 V
Open or ground short in VPA2 circuit 0.5 to 1.1 V 0 to 0.2 V 2.6 to 4.5 V 0 to 0.2 V
EPA circuit open 4.5 to 4.98 V 4.5 to 4.98 V 4.5 to 4.98 V 4.5 to 4.98 V
Normal condition 0.5 to 1.1 V 1.2 to 2.0 V 2.6 to 4.5 V 3.4 to 4.75 V


HINT:
·

Accelerator pedal positions are expressed as voltages.

·

AP stands for Accelerator Pedal.



MONITOR DESCRIPTION

When either output voltage of VPA or VPA2 deviates from the standard range, or the difference between the output voltages of the 2 sensor circuits is less than the threshold, the ECM determines that there is a malfunction in the APP sensor. The ECM then illuminates the MIL and stores DTC(s).

Example:

When the output voltage of VPA drops below 0.4 V for more than 0.5 seconds when the accelerator pedal is fully depressed, DTC P2122 is stored.

If the malfunction is not repaired successfully, a DTC is stored 2 seconds after the engine is next started.

FAIL-SAFE

When any of DTCs P2120, P2121, P2122, P2123, P2125, P2127, P2128 and P2138 is stored, the ECM enters fail-safe mode. If either of the 2 sensor circuits malfunctions, the ECM uses the remaining circuit to calculate the accelerator pedal position to allow the vehicle to continue driving. If both of the circuits malfunction, the ECM regards the accelerator pedal as being released. As a result, the throttle valve is closed and the engine idles.

Fail-safe mode continues until a pass condition is detected, and the engine switch is turned off.

WIRING DIAGRAM

A162855E29
6.012,3.118 6.353,3.274 0.341,0.156 10 ECM 5.583,0.363 5.896,0.528 0.313,0.165 10 VPA 5.583,0.998 5.896,1.163 0.313,0.165 10 EPA 5.592,1.227 5.998,1.392 0.406,0.165 10 VCPA 5.592,1.638 5.989,1.803 0.397,0.165 10 VPA2 5.592,2.245 5.989,2.410 0.397,0.165 10 EPA2 5.592,2.488 5.998,2.653 0.406,0.165 10 VCP2 1.606,0.465 1.920,0.631 0.313,0.165 10 VPA 1.606,0.888 1.920,1.054 0.313,0.165 10 EPA 1.498,1.301 1.904,1.467 0.406,0.165 10 VCPA 1.52,1.722 1.916,1.887 0.397,0.165 10 VPA2 1.528,2.143 1.924,2.309 0.397,0.165 10 EPA2 1.512,2.569 1.918,2.734 0.406,0.165 10 VCP2 6.012,2.969 6.310,3.134 0.298,0.165 10 A38 5.33,0.39 5.565,0.555 0.235,0.165 10 53 1.987,0.386 2.101,0.551 0.114,0.165 10 6 1.987,0.806 2.101,0.972 0.114,0.165 10 5 1.987,1.227 2.101,1.392 0.114,0.165 10 4 1.987,1.647 2.101,1.812 0.114,0.165 10 3 1.987,2.067 2.101,2.232 0.114,0.165 10 2 1.987,2.488 2.101,2.653 0.114,0.165 10 1 5.33,0.801 5.565,0.966 0.235,0.165 10 54 5.33,1.224 5.565,1.389 0.235,0.165 10 55 5.33,1.643 5.565,1.808 0.235,0.165 10 56 5.33,2.065 5.565,2.231 0.235,0.165 10 57 5.33,2.484 5.565,2.649 0.235,0.165 10 58 0.151,2.984 0.458,3.149 0.306,0.165 10 A31 0.142,3.141 2.298,3.307 2.156,0.165 10 Accelerator Pedal Position Sensor

CAUTION / NOTICE / HINT

HINT:
·

These DTCs relate to the Accelerator Pedal Position (APP) sensor.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (ACCELERATOR POSITION SENSOR)
FI07052E67
0.385,1.771 1.125,1.969 0.74,0.198 10 false Depressed 2.365,1.771 3.01,1.969 0.646,0.198 10 false Released

a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / ETCS / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.


d.

Read the value displayed on the tester.

Standard Voltage:
Accelerator Pedal Operation Accel Sensor Out No. 1 Accel Sensor Out No. 2
Released → Depressed → Released 0.5 to 4.5 V 1.2 to 4.75 V
Difference between Accel Sensor Out No. 1 and Accel Sensor Out No. 2 is higher than 0.02 V Difference between Accel Sensor Out No. 1 and Accel Sensor Out No. 2 is higher than 0.02 V


Result
Result Proceed to
NG A
OK B



A

2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)

B

5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)
a.

Disconnect the A31 accelerator pedal position (APP) sensor connector.


b.

Disconnect the A38 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A31-6 (VPA) - A38-53 (VPA) Always Below 1 Ω
A31-5 (EPA) - A38-54 (EPA) Always Below 1 Ω
A31-4 (VCPA) - A38-55 (VCPA) Always Below 1 Ω
A31-3 (VPA2) - A38-56 (VPA2) Always Below 1 Ω
A31-2 (EPA2) - A38-57 (EPA2) Always Below 1 Ω
A31-1 (VCP2) - A38-58 (VCP2) Always Below 1 Ω
A31-6 (VPA) or A38-53 (VPA) - body ground Always 10 kΩ or higher
A31-5 (EPA) or A38-54 (EPA) - body ground Always 10 kΩ or higher
A31-4 (VCPA) or A38-55 (VCPA) - body ground Always 10 kΩ or higher
A31-3 (VPA2) or A38-56 (VPA2) - body ground Always 10 kΩ or higher
A31-2 (EPA2) or A38-57 (EPA2) - body ground Always 10 kΩ or higher
A31-1 (VCP2) or A38-58 (VCP2) - body ground Always 10 kΩ or higher




OK

3.CHECK ECM (VCPA AND VCP2 VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK ECM (VCPA AND VCP2 VOLTAGE)
U155549E01
0.063,0.022 2.467,0.387 2.404,0.365 10 Front view of wire harness connector: (to APP Sensor) 0.463,1.737 0.727,1.918 0.264,0.181 10 A31 1.778,2.518 2.178,2.686 0.400,0.167 10 VCPA 0.474,2.518 0.874,2.686 0.400,0.167 10 VCP2 2.427,2.518 2.749,2.686 0.323,0.167 10 EPA 1.134,2.518 1.544,2.686 0.409,0.167 10 EPA2 0.717,2.479 1.304,1.83 false 1.355,2.484 1.462,1.858 false 1.981,2.484 1.733,1.858 false 2.511,2.473 1.896,1.858 false

a.

Disconnect the A31 APP sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A31-4 (VCPA) - A31-5 (EPA) Engine switch on (IG) 4.5 to 5.5 V
A31-1 (VCP2) - A31-2 (EPA2) Engine switch on (IG) 4.5 to 5.5 V




OK

4.REPLACE ACCELERATOR PEDAL ASSEMBLY

NG

4.REPLACE ACCELERATOR PEDAL ASSEMBLY
a.

Replace the accelerator pedal assembly (See page Engine / Hybrid System>3UR-FE (ENGINE CONTROL)>ACCELERATOR PEDAL>REMOVAL).



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester on.



d.

Start the engine.


e.

Allow the engine to idle for 15 seconds.


f.

Enter the following menus: Powertrain / Engine and ECT / DTC.


g.

Read DTCs.

Result
Result Proceed to
P2120, P2122, P2123, P2125, P2127, P2128, and/or P2138 are output A
No DTC is output B



A

B

SYSTEM OK