Home › Engine / Hybrid System › 3UR-FE (ENGINE CONTROL) › SFI SYSTEM(w/ Secondary Air Injection System) › from 2017.08
RM2660E _51 Engine / Hybrid System _052775 3UR-FE ENGINE CONTROL _0327320 SFI SYSTEM(w/ Secondary Air Injection System) J

3UR-FE ENGINE CONTROL  SFI SYSTEM(w/ Secondary Air Injection System)  Fuel Pump Control Circuit  


DESCRIPTION

The fuel pump circuit consists of the ECM, fuel pump and fuel pump ECU (which operates the fuel pump). Based on the engine output, the ECM determines the fuel pump speed. The speed is then converted to a duty signal and sent to the fuel pump ECU. Based on the signal sent from the ECM, the fuel pump ECU adjusts the fuel pump operation speed.

WIRING DIAGRAM

A351219E08
4.719,1.958 4.979,2.156 0.26,0.198 10 false 1R 0.865,5.521 1.333,5.667 0.469,0.146 10 false Battery 3.031,6.24 3.313,6.385 0.281,0.146 10 false N1 3.031,6.406 3.74,6.563 0.708,0.156 10 false Fuel Pump 3.771,5.375 3.865,5.521 0.094,0.146 10 false 5 2.885,5.375 2.99,5.521 0.104,0.146 10 false 4 3.042,5.583 3.24,5.74 0.198,0.156 10 false B2 3.51,5.583 3.708,5.729 0.198,0.146 10 false E2 2.865,5.083 3.01,5.24 0.146,0.156 10 false 1 3.771,5.083 3.896,5.24 0.125,0.156 10 false 2 2.896,4.854 3.104,5 0.208,0.146 10 false FP 3.583,4.854 3.833,5 0.25,0.146 10 false FP- 2.656,4.271 2.75,4.417 0.094,0.146 10 false 3 2.854,4.375 2.969,4.521 0.115,0.146 10 false E 3.99,4.771 4.677,5.083 0.688,0.313 10 false Fuel Pump ECU 6.188,6.219 6.448,6.365 0.26,0.146 10 false A38 6.177,6.375 6.51,6.521 0.333,0.146 10 false ECM 5.677,0.74 5.896,0.917 0.219,0.177 10 false 6 5.906,0.833 6.313,0.979 0.406,0.146 10 false MREL 5.594,4.26 5.813,4.448 0.219,0.188 10 false 50 5.885,4.26 6.177,4.417 0.292,0.156 10 false FPC 3.99,4.615 4.354,4.802 0.365,0.188 10 false N14 1.021,0.833 1.313,1.021 0.292,0.188 10 false 1S 1.021,1.948 1.292,2.135 0.271,0.188 10 false 1X 2.271,2.667 3.76,2.875 1.49,0.208 10 false No. 2 Integration Relay 2.458,1.781 3.615,1.979 1.156,0.198 10 false EFI MAIN NO. 1 1.75,2.115 2.656,2.313 0.906,0.198 10 false FUEL PMP 0.698,3.958 1.313,4.156 0.615,0.198 10 false P/I-B 1.063,1.76 1.323,1.958 0.26,0.198 10 false 1 4.458,1.052 4.719,1.25 0.26,0.198 10 false 11 4.771,0.656 5.031,0.854 0.26,0.198 10 false 8 1.052,0.656 1.313,0.854 0.26,0.198 10 false 4 4.698,0.833 4.99,1.021 0.292,0.188 10 false 1S 4.719,1.156 5.01,1.344 0.292,0.188 10 false 1S 5.677,1.073 5.875,1.271 0.198,0.198 10 false 2 5.906,1.177 6.385,1.375 0.479,0.198 10 false +B 5.677,1.375 5.896,1.552 0.219,0.177 10 false 3 5.906,1.5 6.385,1.688 0.479,0.188 10 false +B2 1.583,1.615 2.74,1.813 1.156,0.198 10 false EFI MAIN NO. 1 3.698,2.281 4.604,2.479 0.906,0.198 10 false FUEL PMP 4.76,1.771 5.021,1.969 0.26,0.198 10 false 6 4.521,1.375 4.781,1.573 0.26,0.198 10 false 7 4.708,1.469 5,1.656 0.292,0.188 10 false 1R 3.969,3.573 4.333,3.76 0.365,0.188 10 false 6 3.677,3.677 4.042,3.865 0.365,0.188 10 false +B 3.552,4.354 3.917,4.542 0.365,0.188 10 false FPC 3.979,4.25 4.344,4.438 0.365,0.188 10 false 5

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP/SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.


e.

Check whether operating sounds can be heard while operating the fuel pump using the GTS.

OK:

Operating sounds can be heard from fuel pump.



Result
Result Proceed to
NG A
OK B


OK

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP)

NG

8.INSPECT FUEL PUMP ECU (POWER SOURCE VOLTAGE)
2.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP)
A243665E01
2.862,1.37 2.973,1.519 0.111,0.149 10 1 0.647,1.391 0.755,1.544 0.107,0.152 10 2 1.931,1.67 2.821,1.462 false 1.539,1.671 0.796,1.478 false 0.178,0.144 2.543,0.541 2.365,0.397 10 Component with harness connected: (Fuel Pump)

a.

Remove the fuel tank assembly (See page Engine / Hybrid System>3UR-FE (FUEL)>FUEL TANK>REMOVAL).


b.

Remove the fuel pump from the fuel tank assembly.


c.

Clean the fuel pump to completely remove any remaining fuel.


d.

Connect the fuel pump connector.

CAUTION:

Confirm that no fuel remains inside or on the outside of the fuel pump.



e.

Connect the GTS to the DLC3.


f.

Turn the engine switch on (IG).


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump Duty.


i.

Operate the fuel pump using the Active Test function and measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Tester Operation Specified Condition
1 - 2 FPC Duty: 25% 3.2 to 4.05 V
FPC Duty: 80% 8.8 to 12.5 V



j.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.


k.

Operate the fuel pump using the Active Test function and measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Tester Operation Specified Condition
1 - 2 ON (FPC Duty: 90%) 9.0 to 14.0 V



HINT:
·

Be sure to measure the voltage with all of the connectors connected.

·

Before performing this inspection, check that the battery voltage is between 11 and 14 V (not depleted).




OK

3.CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM)

NG

6.REPLACE FUEL PUMP ECU
3.CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM)
a.

Disconnect the fuel pump ECU connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N14-5 (FPC) - A38-50 (FPC) Always Below 1 Ω
N14-5 (FPC) or A38-50 (FPC) - Body ground Always 10 kΩ or higher




OK

4.REPLACE FUEL PUMP

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE FUEL PUMP
a.

Replace the fuel pump (See page Engine / Hybrid System>3UR-FE (FUEL)>FUEL PUMP>REMOVAL).

HINT:

Perform "Inspection After Repair" after replacing the fuel pump (See page Engine / Hybrid System>3UR-FE (ENGINE CONTROL)>SFI SYSTEM(w/ Secondary Air Injection System)>INITIALIZATION).




NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check the fuel pump operation.

OK:

Malfunction has been repaired successfully.




OK

END

NG

6.REPLACE FUEL PUMP ECU
a.

Replace the fuel pump ECU (See page Engine / Hybrid System>3UR-FE (FUEL)>FUEL PUMP ECU>REMOVAL).



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check the fuel pump operation.

OK:

Malfunction has been repaired successfully.




OK

END

NG

8.INSPECT FUEL PUMP ECU (POWER SOURCE VOLTAGE)
U163418E01
2.404,1.917 2.598,2.070 0.194,0.152 10 +B 2.212,1.446 2.506,1.903 false 0.25,1.227 0.587,1.407 0.338,0.180 10 N14 0.048,0.039 2.400,0.383 2.353,0.344 10 Front view of wire harness connector: (to Fuel Pump ECU)

a.

Disconnect the fuel pump ECU connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N14-6 (+B) - Body Ground Engine switch on (IG) 11 to 14 V




OK

9.CHECK HARNESS AND CONNECTOR (FUEL PUMP - FUEL PUMP ECU)

NG

12.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY - FUEL PUMP ECU)
9.CHECK HARNESS AND CONNECTOR (FUEL PUMP - FUEL PUMP ECU)
a.

Disconnect the fuel pump connector.


b.

Disconnect the fuel pump ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N1-4 (B2) - N14-1 (FP) Always Below 1 Ω
N1-5 (E2) - N14-2 (FP-) Always Below 1 Ω
N1-4 (B2) or N14-1 (FP) - Body ground Always 10 kΩ or higher
N1-5 (E2) or N14-2 (FP-) - Body ground Always 10 kΩ or higher




OK

10.INSPECT FUEL PUMP

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT FUEL PUMP
a.

Inspect the fuel pump (See page Engine / Hybrid System>3UR-FE (FUEL)>FUEL PUMP>INSPECTION).

HINT:

Perform "Inspection After Repair" after replacing the fuel pump (See page Engine / Hybrid System>3UR-FE (ENGINE CONTROL)>SFI SYSTEM(w/ Secondary Air Injection System)>INITIALIZATION).




OK

11.CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM, BODY GROUND)

NG

11.CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM, BODY GROUND)
a.

Disconnect the fuel pump ECU connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-50 (FPC) - N14-5 (FPC) Always Below 1 Ω
N14-3 (E) - Body ground Always Below 1 Ω
A38-50 (FPC) or N14-5 (FPC) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY - FUEL PUMP ECU)
a.

Disconnect the fuel pump ECU connector.


b.

Disconnect the No. 2 integration relay connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1R-6 - N14-6 (+B) Always Below 1 Ω
1R-6 or N14-6 (+B) - Body ground Always 10 kΩ or higher




OK

13.INSPECT NO. 2 INTEGRATION RELAY (FUEL PMP)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.INSPECT NO. 2 INTEGRATION RELAY (FUEL PMP)
a.

Inspect the No. 2 integration relay (FUEL PMP) (See page Engine / Hybrid System>3UR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).



OK

NG

REPLACE NO. 2 INTEGRATION RELAY