Home › Engine / Hybrid System › 3UR-FE (ENGINE CONTROL) › SFI SYSTEM(w/ Secondary Air Injection System) › from 2017.08
RM2660E _51 Engine / Hybrid System _052775 3UR-FE ENGINE CONTROL _0327320 SFI SYSTEM(w/ Secondary Air Injection System) J

3UR-FE ENGINE CONTROL  SFI SYSTEM(w/ Secondary Air Injection System)  Starter Signal Circuit  


DESCRIPTION

While the engine is being cranked, current flows from terminal STAR of the certification ECU (smart key ECU assembly) to the park/neutral position switch assembly and to terminal STA of the ECM (STA signal).

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK WHETHER ENGINE CAN BE CRANKED
a.

Check if the engine can be cranked.

Result
Result Proceed to
Engine cannot be cranked A
Engine can be cranked B



A

2.READ VALUE USING GTS (STARTER SIGNAL)

B

12.READ VALUE USING GTS (STARTER SIGNAL)
2.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.


e.

Check the value displayed on the GTS when the engine switch is turned to the START.

OK:
Engine Switch Position Display (Starter Signal)
Engine switch on (IG) Close or OFF
Engine started Open or ON




OK

3.INSPECT STARTER RELAY (ST)

NG

10.INSPECT PARK/NEUTRAL POSITION SWITCH
3.INSPECT STARTER RELAY (ST)
a.


OK

4.INSPECT STARTER

NG

REPLACE STARTER RELAY (ST)

4.INSPECT STARTER

OK

5.CHECK HARNESS AND CONNECTOR (ST RELAY - STARTER)

NG

REPAIR OR REPLACE STARTER

5.CHECK HARNESS AND CONNECTOR (ST RELAY - STARTER)
a.

Remove the starter relay (ST) from the engine room relay block.


b.

Disconnect the starter connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST relay (3) - D2-1 Always Below 1 Ω
ST relay (3) or D2-1 - Body ground Always 10 kΩ or higher




OK

6.CHECK HARNESS AND CONNECTOR (BATTERY - STARTER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (BATTERY - STARTER)
a.

Disconnect the starter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D16-1 - Body ground Always 11 to 14 V




OK

7.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)
a.

Remove the starter relay (ST) from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST relay (1) - Body ground Always Below 1 Ω




OK

8.CHECK HARNESS AND CONNECTOR (ST RELAY - PNP SWITCH, SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (ST RELAY - PNP SWITCH, SMART KEY ECU ASSEMBLY)
a.

Remove the starter relay (ST) from the engine room relay block.


b.

Disconnect the PNP switch connector.


c.

Disconnect the smart key ECU assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST relay (2) - E128-12 (STA) Always Below 1 Ω
ST relay (2) - C24-8 Always Below 1 Ω
ST relay (2) or E128-12 (STA) - Body ground Always 10 kΩ or higher
ST relay (2) - C24-8 - Body ground Always 10 kΩ or higher




OK

9.CHECK STARTER RELAY (POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK STARTER RELAY (POWER SOURCE)
A351236E01
0.871,2.915 2.629,3.121 1.758,0.207 10 Engine Room Relay Block 0.023,1.465 0.896,1.913 0.873,0.448 10 Starter Relay (ST)

a.

Remove the starter relay (ST) from the engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
ST relay (5) - Body ground Always 11 to 14 V




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT PARK/NEUTRAL POSITION SWITCH
a.


OK

11.CHECK HARNESS AND CONNECTOR (PNP SWITCH - ECM, SMART KEY ECU ASSEMBLY)

NG

11.CHECK HARNESS AND CONNECTOR (PNP SWITCH - ECM, SMART KEY ECU ASSEMBLY)
a.

Disconnect the smart key ECU assembly connector.


b.

Disconnect the PNP switch connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C24-3 - E128-10 (STAR) Always Below 1 Ω
C45-48 (NSW) - E128-10 (STAR) Always Below 1 Ω
C24-3 or E128-10 (STAR) - Body ground Always 10 kΩ or higher
C45-48 (NSW) or E128-10 (STAR) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.


e.

Check the value displayed on the GTS when the engine switch is turned to the START.

OK:
Engine Switch Position Display (Starter Signal)
Engine switch on (IG) Close or OFF
Engine started Open or ON




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR