Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE) › from 2017.08
RM2660E _52 Drivetrain _066407 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0327282 AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE) C

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE)  P2773  Four Wheel Drive (4WD) Low Switch Circuit Low  


DESCRIPTION

The ECM detects the signal from the transfer L4 position switch.

This DTC indicates that the transfer L4 position switch remains on.

DTC Code DTC Detection Condition Trouble Area
P2773 Transfer L4 position switch remains on while the vehicle is being driven under the following conditions for 1.8 seconds or more (1 trip detection logic):
(a) Output shaft speed is between 1000 and 3000 rpm.
(b) Transfer position switch is in H4.
·

Short in transfer L4 position switch circuit

·

Transfer system

·

ECM



MONITOR DESCRIPTION

The ECM monitors the transfer case L4 position switch to determine when the transfer case L4 gears are engaged. If the transfer case L4 gears remain engaged under the following conditions, the ECM will conclude that there is a malfunction of the L4 position switch, illuminate the MIL and store the DTC:

·

The L4 switch indicates that the L4 transfer case gears are engaged.

·

The transfer position switch is in H4.

·

The transfer case output shaft speed is between 1000 and 3000 rpm.

·

The specified time period has elapsed.


WIRING DIAGRAM

C328828E11
0.74,3.135 2.75,3.333 2.01,0.198 10 false 4 Wheel Drive Control ECU 0.719,2.948 1.115,3.146 0.396,0.198 10 false A27 5.01,1.979 5.51,2.177 0.5,0.198 10 false L4 2.063,1.979 2.563,2.177 0.5,0.198 10 false L4 5.844,1.135 6.344,1.333 0.5,0.198 10 false 12 V 4.729,1.979 5.063,2.177 0.333,0.198 10 false 35 2.365,1.979 2.604,2.177 0.24,0.198 10 false 16 5.427,2.948 5.927,3.146 0.5,0.198 10 false A38 5.427,3.135 5.927,3.333 0.5,0.198 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced (See page Drivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE)>PRECAUTION)


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - BODY GROUND)
a.
U148300E04
2.583,1.792 2.406,1.167 true 0.052,0 0.365,0.198 0.313,0.198 10 false *a 1.573,0.25 1.948,0.479 0.375,0.229 10 false A27 2.552,1.823 2.802,2.021 0.25,0.198 10 false L4

Disconnect the 4 wheel drive control ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A27-16 (L4) - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to 4 Wheel Drive Control ECU)



OK

NG

2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - ECM)
2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - ECM)
a.

Disconnect the 4 wheel drive control ECU connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A27-16 (L4) or A38-35 (L4) - Body ground and other terminals Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR