Home › Drivetrain › AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM › from 2017.08
RM2660E _52 Drivetrain _052807 AE80F AUTOMATIC TRANSMISSION / TRANSAXLE _0255308 AUTOMATIC TRANSMISSION SYSTEM C

AE80F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P2772  Four Wheel Drive (4WD) Low Switch Circuit Range / Performance  


DESCRIPTION

The TCM detects the signal from the transfer L4 position switch.

This DTC indicates that the transfer L4 position switch remains on or off.

DTC Code DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P2772
1.

The transfer position switch is in H4 and transfer output shaft speed is between 1000 and 3000 rpm

2.

The transfer L4 position switch remains on

3.

1.8 seconds or more

4.

1-trip detection logic


·

Short in transfer L4 position switch circuit

·

Four wheel drive control ECU

·

TCM


1.

The transfer position switch is in L4 and transfer output shaft speed is between 1000 and 3000 rpm

2.

The transfer L4 position switch remains off

3.

1.8 seconds or more

4.

1-trip detection logic


·

Open in transfer L4 position switch circuit

·

Four wheel drive control ECU

·

TCM



MONITOR DESCRIPTION

ON malfunction:

The TCM monitors the transfer case L4 position switch to determine when the transfer case L4 gears are engaged. If the transfer case L4 gears remain engaged under the following conditions, the TCM will conclude that there is a malfunction of the L4 position switch, illuminate the MIL* and store the DTC:

-

The L4 switch indicates that the L4 transfer case gears are engaged.

-

The transfer position switch is in H4.

-

The transfer case output shaft speed is between 1000 and 3000 rpm.

-

The specified time period has elapsed.



OFF malfunction:

The TCM monitors the transfer case L4 position switch to determine when the transfer case L4 gears are engaged. If the transfer case H4 gears remain engaged under the following conditions, the TCM will conclude that there is a malfunction of the L4 position switch, illuminate the MIL* and store the DTC:

-

The L4 switch indicates that the H4 transfer case gears are engaged.

-

The transfer position switch is in L4.

-

The transfer case output shaft speed is between 1000 and 3000 rpm.

-

The specified time period has elapsed.



*: w/ OBD


WIRING DIAGRAM

C328828E07
0.669,3.079 2.676,3.274 2.007,0.196 10 4 Wheel Drive Control ECU 0.669,2.898 1.062,3.094 0.392,0.196 10 A27 5.014,1.977 5.515,2.173 0.502,0.196 10 L4 2.059,1.977 2.560,2.173 0.502,0.196 10 L4 5.841,1.07 6.343,1.266 0.502,0.196 10 12 V 4.676,1.977 4.912,2.173 0.236,0.196 10 24 2.365,1.977 2.601,2.173 0.236,0.196 10 16 5.425,2.898 5.927,3.094 0.502,0.196 10 A82 5.425,3.079 5.927,3.274 0.502,0.196 10 TCM

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION).


HINT:

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the transfer position switch to L4.

2.

Drive the vehicle at 15 to 20 km/h (9 to 12 mph) for 1.8 seconds or more.

3.

Turn the transfer position switch to H4.

4.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (L4 TERMINAL VOLTAGE)
a.
U156213E04
2.406,1.167 2.604,1.646 true 0.125,0.063 0.406,0.24 0.281,0.177 10 false *a 2.563,1.698 2.927,1.885 0.365,0.188 10 false L4 1.583,0.229 1.938,0.406 0.354,0.177 10 false A27

Disconnect the 4 wheel drive control ECU connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A27-16 (L4) - Body ground Engine switch on (IG) 11 to 14 V

Text in Illustration
*a Front view of wire harness connector
(to 4 Wheel Drive Control ECU)




OK

2.CHECK TRANSFER SYSTEM

NG

3.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - TCM)
2.CHECK TRANSFER SYSTEM

b.

If no malfunction is found, proceed to the next step.



NEXT

3.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - TCM)
a.

Disconnect the A27 4 wheel drive control ECU connector.


b.

Disconnect the A82 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A27-16 (L4) - A82-24 (L4) Always Below 1 Ω
A27-16 (L4) or A82-24 (L4) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR