Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2017.08
RM2660E _51 Engine / Hybrid System _052774 1GR-FE ENGINE CONTROL _0255001 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0120  Throttle / Pedal Position Sensor / Switch "A" Circuit Malfunction  P0121  Throttle / Pedal Position Sensor / Switch "A" Circuit Range / Performance Problem  P0122  Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input  P0123  Throttle / Pedal Position Sensor / Switch "A" Circuit High Input  P0220  Throttle / Pedal Position Sensor / Switch "B" Circuit  P0222  Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input  P0223  Throttle / Pedal Position Sensor / Switch "B" Circuit High Input  P2135  Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation  


CAUTION / NOTICE / HINT

DESCRIPTION

The throttle position sensor is mounted on the throttle body with motor assembly and detects the opening angle of the throttle valve. This sensor is a non-contact type. It uses Hall-effect elements in order to yield accurate signals even in extreme driving conditions, such as at high speeds as well as very low speeds.

The throttle position sensor has 2 sensor circuits, each of which transmits a signal, VTA1 and VTA2. VTA1 is used to detect the throttle valve opening angle and VTA2 is used to detect malfunctions in VTA1. The sensor signal voltages vary between 0 V and 5 V in proportion to the throttle valve opening angle, and are transmitted to the VTA terminals of the ECM.

As the valve closes, the sensor output voltage decreases and as the valve opens, the sensor output voltage increases. The ECM calculates the throttle valve opening angle according to these signals and controls the throttle actuator in response to driver inputs. These signals are also used in calculations such as air-fuel ratio correction, power increase correction and fuel-cut control.

U163315E02
4.396,1.51 4.646,1.052 4.646,1.052 4.74,1.052 false 0.833,1.573 0.885,2.198 false 1.25,1.094 0.927,1.896 false 0.885,2.938 1.365,3.563 false 0.865,2.583 0.479,3.125 false 5.719,0.531 5.885,0.531 5.885,0.531 6.146,1.854 false 5.531,2.25 5.896,2.552 false 5.531,2.333 5.531,2.146 false 3.885,1.656 4.219,1.813 0.333,0.156 10 false 4.65 4.573,1.917 4.948,2.083 0.375,0.167 10 false VTA2 4.969,2.708 5.344,2.875 0.375,0.167 10 false VTA1 3.823,2.26 4.198,2.417 0.375,0.156 10 false 2.60* 3.896,2.406 4.198,2.563 0.302,0.156 10 false 2.25 3.833,2.74 4.188,2.896 0.354,0.156 10 false 0.97* 3.896,2.885 4.198,3.042 0.302,0.156 10 false 0.69 3.958,1.417 4.188,1.573 0.229,0.156 10 false 5.0 4.792,0.99 5.771,1.146 0.979,0.156 10 false Fail-safe Angle 2.677,1.01 4.344,1.188 1.667,0.177 10 false Sensor Output Voltage (V) 6.479,3.406 6.833,3.563 0.354,0.156 10 false 86° 4.354,3.125 4.531,3.281 0.177,0.156 10 false 7° 4.167,3.417 4.427,3.573 0.26,0.156 10 false 0° 1.969,1.135 2.313,1.302 0.344,0.167 10 false ECM 1.302,1.75 1.719,1.906 0.417,0.156 10 false VCTA 1.302,2.75 1.646,2.906 0.344,0.156 10 false ETA 1.302,2.083 1.698,2.24 0.396,0.156 10 false VTA1 1.302,2.417 1.698,2.573 0.396,0.156 10 false VTA2 1.271,1.031 1.792,1.208 0.521,0.177 10 false Magnet 1.396,3.479 1.917,3.656 0.521,0.177 10 false Magnet 0.302,1.49 0.885,1.667 0.583,0.177 10 false IC No. 1 0.302,3.146 0.896,3.323 0.594,0.177 10 false IC No. 2 0.031,0.656 1.635,0.833 1.604,0.177 10 false Throttle Position Sensor 0.073,3.708 0.51,3.875 0.438,0.167 10 false Note: 0.073,4.021 3.396,4.365 3.323,0.344 10 false The throttle valve opening angle detected by sensor terminal VTA1 is expressed as a percentage. 0.073,4.771 3.438,4.958 3.365,0.188 10 false Between 10% and 22%: Throttle valve fully closed 0.073,5.115 3.333,5.271 3.26,0.156 10 false Between 67.2% and 99.2%: Throttle valve fully open 0.073,5.438 2.792,5.594 2.719,0.156 10 false Approximately 19.4%: Fail-safe angle (7°) 4.031,0.448 5.719,0.635 1.688,0.188 10 false Line indicating VTA2 x 0.8 3.604,4.573 5.635,4.75 2.031,0.177 10 false Characteristics of sensor output: 5.896,2.51 6.354,2.729 0.458,0.219 10 false 1.11 V 5.104,3.677 7.135,3.875 2.031,0.198 10 false Throttle Valve Opening Angle (°) 4.948,3.323 6.094,3.521 1.146,0.198 10 false Usable Range 4.646,4.083 6.24,4.281 1.594,0.198 10 false *: During fail-safe control 3.604,5.656 7.042,5.833 3.438,0.177 10 false (VTA2 x 0.8 is approximately equal to VTA1 + 1.11 V) 3.604,4.938 7.104,5.271 3.5,0.333 10 false The difference in voltage between VTA1 and VTA2 x 0.8 is approximately 1.11 V.

DTC No. DTC Detection Condition Trouble Area
P0120 Output voltage of VTA1 quickly fluctuates beyond the lower and upper malfunction thresholds for 2 seconds when the accelerator pedal is depressed (1 trip detection logic).
·

Throttle position sensor (built into throttle body with motor assembly)

·

ECM


P0121 Difference between VTA1 and VTA2 voltages is less than 0.8 V, or more than 1.6 V for 2 seconds (1 trip detection logic).
·

Throttle position sensor (built into throttle body with motor assembly)

·

Throttle position sensor circuit

·

ECM


P0122 Output voltage of VTA1 is 0.2 V or less for 2 seconds when the accelerator pedal is depressed (1 trip detection logic).
·

Throttle position sensor (built into throttle body with motor assembly)

·

Short in VTA1 circuit

·

Open in VC circuit

·

ECM


P0123 Output voltage of VTA1 is 4.54 V or higher for 2 seconds when the accelerator pedal is depressed (1 trip detection logic).
·

Throttle position sensor (built into throttle body with motor assembly)

·

Open in VTA1 circuit

·

Open in ETA circuit

·

Short between VC and VTA1 circuits

·

ECM


P0220 Output voltage of VTA2 quickly fluctuates beyond the lower and upper malfunction thresholds for 2 seconds when the accelerator pedal is depressed (1 trip detection logic).
·

Throttle position sensor (built into throttle body with motor assembly)

·

ECM


P0222 Output voltage of VTA2 is 1.75 V or less for 2 seconds when the accelerator pedal is depressed (1 trip detection logic).
·

Throttle position sensor (built into throttle body with motor assembly)

·

Short in VTA2 circuit

·

Open in VC circuit

·

ECM


P0223 Output voltage of VTA2 is 4.8 V or higher, and VTA1 is between 0.2 V and 2.02 V for 2 seconds when the accelerator pedal is depressed (1 trip detection logic).
·

Throttle position sensor (built into throttle body with motor assembly)

·

Open in VTA2 circuit

·

Open in ETA circuit

·

Short between VC and VTA2 circuits

·

ECM


P2135 Either condition is met (1 trip detection logic):
(a) Difference between the output voltages of VTA1 and VTA2 is 0.02 V or less for 0.5 seconds or more.
(b) Output voltage of VTA1 is 0.2 V or less, and VTA2 is 1.75 V or less for 0.4 seconds or more.
·

Throttle position sensor (built into throttle body with motor assembly)

·

Short between VTA1 and VTA2 circuits

·

ECM



HINT:
·

When any of these DTCs is stored, check the throttle valve opening angle by entering the following menus: Powertrain / Engine and ECT / Data List / All Data / Throttle Position No.1 and Throttle Position No.2.


·

Throttle Position No.1 is the VTA1 signal, and Throttle Position No.2 is the VTA2 signal.

Reference (Normal Condition):
GTS Display Accelerator Pedal Fully Released Accelerator Pedal Fully Depressed
Throttle Position No.1 0.5 to 1.1 V 3.3 to 4.9 V
Throttle Position No.2 2.1 to 3.1 V 4.6 to 5.0 V




MONITOR DESCRIPTION

The ECM uses the throttle position sensor to monitor the throttle valve opening angle. There are several checks that the ECM performs to confirm that the throttle position sensor is operating properly.

P0120, P0122, P0123, P0220, P0222, P0223 and P2135
·

A specific voltage difference is expected between the sensor terminals, VTA1 and VTA2, for each throttle valve opening angle. If the difference between VTA1 and VTA2 is incorrect, the ECM interprets this as a malfunction in the sensor and stores a DTC.

·

VTA1 and VTA2 each have a specific voltage range. If VTA1 or VTA2 is outside the normal operating range, the ECM interprets this as a malfunction in the sensor and stores a DTC.

·

VTA1 and VTA2 should never be close to the same voltage level. If VTA1 is within 0.02 V of VTA2, the ECM determines that there is a short circuit in the sensor and stores a DTC.


If the malfunction is not repaired successfully, a DTC is stored 10 seconds after the engine is next started.

P0121

The ECM uses the throttle position sensor to monitor the throttle valve opening angle.

This sensor transmits two signals: VTA1 and VTA2. VTA1 is used to detect the throttle opening angle and VTA2 is used to detect malfunctions in VTA1. The ECM performs several checks to confirm that the throttle position sensor and VTA1 are operating properly.

For each throttle opening angle, a specific voltage difference is expected between the outputs of VTA1 and VTA2. If the output voltage difference between the two signals deviates from the normal operating range, the ECM interprets this as a malfunction of the throttle position sensor. The ECM illuminates the MIL and stores the DTC.

If the malfunction is not repaired successfully, the DTC is stored 2 seconds after the engine is next started.


FAIL-SAFE

When any of these DTCs as well as other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 7° opening angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing in accordance with the accelerator pedal position to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

The ECM continues operating in fail-safe mode until a pass condition is detected and the ignition switch is turned off.

WIRING DIAGRAM

for Manual Transmission Models
A227101E10
0.99,3.781 2.573,4.177 1.583,0.396 10 false Throttle Body with Motor Assembly 0.99,3.635 1.26,3.781 0.271,0.146 10 false C3 5.104,3.813 5.448,3.969 0.344,0.156 10 false ECM 5.104,3.646 5.99,3.802 0.885,0.156 10 false C45 2.01,1.208 2.302,1.375 0.292,0.167 10 false VTA 1.969,1.823 2.333,1.979 0.365,0.156 10 false VTA2 2.104,2.469 2.333,2.625 0.229,0.156 10 false VC 2.125,3.073 2.354,3.24 0.229,0.167 10 false E2 2.438,1.094 2.552,1.26 0.115,0.167 10 false 6 2.448,1.74 2.573,1.885 0.125,0.146 10 false 4 2.438,2.354 2.563,2.542 0.125,0.188 10 false 5 2.448,2.979 2.563,3.125 0.115,0.146 10 false 3 4.531,1.094 4.719,1.24 0.188,0.146 10 false 78 4.542,1.729 4.729,1.875 0.188,0.146 10 false 77 4.531,2.354 4.729,2.51 0.198,0.156 10 false 80 4.542,2.969 4.729,3.115 0.188,0.146 10 false 79 4.781,1.094 5.146,1.26 0.365,0.167 10 false VTA1 4.781,1.729 5.146,1.875 0.365,0.146 10 false VTA2 4.771,2.354 5.167,2.49 0.396,0.135 10 false VCTA 4.781,2.969 5.115,3.135 0.333,0.167 10 false ETA 5.958,2.25 6.188,2.417 0.229,0.167 10 false 5 V


for Automatic Transmission Models
A227101E11
0.99,3.781 2.573,4.177 1.583,0.396 10 false Throttle Body with Motor Assembly 0.99,3.635 1.26,3.781 0.271,0.146 10 false C3 5.104,3.813 5.448,3.969 0.344,0.156 10 false ECM 5.104,3.646 5.99,3.802 0.885,0.156 10 false C45 2.01,1.208 2.302,1.375 0.292,0.167 10 false VTA 1.969,1.823 2.333,1.979 0.365,0.156 10 false VTA2 2.104,2.469 2.333,2.625 0.229,0.156 10 false VC 2.125,3.073 2.344,3.25 0.219,0.177 10 false E2 2.438,1.094 2.552,1.26 0.115,0.167 10 false 6 2.448,1.74 2.573,1.885 0.125,0.146 10 false 4 2.438,2.354 2.563,2.542 0.125,0.188 10 false 5 2.448,2.979 2.563,3.125 0.115,0.146 10 false 3 4.448,1.094 4.719,1.281 0.271,0.188 10 false 126 4.458,1.729 4.729,1.927 0.271,0.198 10 false 101 4.448,2.354 4.729,2.521 0.281,0.167 10 false 125 4.458,2.948 4.729,3.146 0.271,0.198 10 false 124 4.781,1.094 5.146,1.26 0.365,0.167 10 false VTA1 4.781,1.729 5.146,1.875 0.365,0.146 10 false VTA2 4.771,2.354 5.167,2.49 0.396,0.135 10 false VCTA 4.781,2.969 5.115,3.135 0.333,0.167 10 false ETA 5.958,2.25 6.188,2.417 0.229,0.167 10 false 5 V


CAUTION / NOTICE / HINT

HINT:
·

These DTCs relate to the throttle position sensor.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (THROTTLE POSITION NO.1 AND NO.2)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Position No.1 and Throttle Position No.2.


d.

Check the values displayed on the GTS.

Result
When Accelerator Pedal Released When Accelerator Pedal Depressed Trouble Area Proceed to
Throttle Position No.1 Throttle Position No.2 Throttle Position No.1 Throttle Position No.2
0 to 0.2 V 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V VC circuit open A
4.5 to 5.0 V 4.5 to 5.0 V 4.5 to 5.0 V 4.5 to 5.0 V ETA circuit open
0 to 0.2 V,
or 4.5 to 5.0 V
2.4 to 3.4 V
(Fail-safe)
0 to 0.2 V,
or 4.5 to 5.0 V
2.4 to 3.4 V
(Fail-safe)
VTA1 circuit open or shorted to ground
0.7 to 1.3 V
(Fail-safe)
0 to 0.2 V,
or 4.5 to 5.0 V
0.7 to 1.3 V
(Fail-safe)
0 to 0.2 V,
or 4.5 to 5.0 V
VTA2 circuit open or shorted to ground
0.5 to 1.1 V 2.1 to 3.1 V 3.3 to 4.9 V
(Not fail-safe)
4.6 to 5.0 V
(Not fail-safe)
TP sensor circuit normal B

HINT:
·

DTC P0121 is stored when the VTA1 and VTA2 output voltages are not consistent with the sensor characteristics. Therefore, check the freeze frame data when this DTC is stored. Use the following formula to confirm the relative differences in voltage.

Calculate the voltage of VTA1 and VTA2 according to Throttle Sensor Volt % and Throttl Sensor #2 Volt % respectively and confirm their consistency.

Example:

Throttle Sensor Volt % / 100 (%) x 5 (V) = Throttle Position No.1

Characteristic Sensor Output:

VTA2 x 0.8 is approximately equal to VTA1 + 1.11 V

VTA1: Throttle Position No.1

VTA2: Throttle Position No.2


·

If DTC P0121 is output, proceed to "CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)".





A

2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)

B

5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)
a.

Disconnect the throttle body with motor assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Manual Transmission Models
Tester Connection Condition Specified Condition
C3-5 (VC) - C45-80 (VCTA) Always Below 1 Ω
C3-6 (VTA) - C45-78 (VTA1) Always Below 1 Ω
C3-4 (VTA2) - C45-77 (VTA2) Always Below 1 Ω
C3-3 (E2) - C45-79 (ETA) Always Below 1 Ω
C3-5 (VC) or C45-80 (VCTA) - Body ground Always 10 kΩ or higher
C3-6 (VTA) or C45-78 (VTA1) - Body ground Always 10 kΩ or higher
C3-4 (VTA2) or C45-77 (VTA2) - Body ground Always 10 kΩ or higher

for Automatic Transmission Models
Tester Connection Condition Specified Condition
C3-5 (VC) - C45-125 (VCTA) Always Below 1 Ω
C3-6 (VTA) - C45-126 (VTA1) Always Below 1 Ω
C3-4 (VTA2) - C45-101 (VTA2) Always Below 1 Ω
C3-3 (E2) - C45-124 (ETA) Always Below 1 Ω
C3-5 (VC) or C45-125 (VCTA) - Body ground Always 10 kΩ or higher
C3-6 (VTA) or C45-126 (VTA1) - Body ground Always 10 kΩ or higher
C3-4 (VTA2) or C45-101 (VTA2) - Body ground Always 10 kΩ or higher




OK

3.INSPECT ECM (VC VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ECM (VC VOLTAGE)
U163286E01
0.664,0.942 0.893,1.123 0.229,0.181 10 C3 0.185,0.097 0.341,0.278 0.156,0.181 10 *a 1.669,1.079 1.471,1.569 false 1.944,1.079 2.133,1.56 false 1.36,1.598 1.547,1.779 0.187,0.181 10 E2 2.03,1.598 2.240,1.779 0.210,0.181 10 VC

a.

Disconnect the throttle body with motor assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C3-5 (VC) - C3-3 (E2) Ignition switch ON 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to Throttle Body with Motor Assembly)



OK

4.REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

NG

4.REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY
a.

Replace the throttle body with motor assembly (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>THROTTLE BODY>REMOVAL).



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.



d.

Start the engine.


e.

Allow the engine to idle for 15 seconds or more.


f.

Read the output DTCs.

Result
Result Proceed to
P0120, P0121, P0122, P0123, P0220, P0222, P0223 and/or P2135 is output A
No DTC is output B



A

B

SYSTEM OK