Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2017.08
RM2660E _51 Engine / Hybrid System _052774 1GR-FE ENGINE CONTROL _0255001 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0443  Evaporative Emission Control System Purge Control Valve Circuit  


DESCRIPTION

To reduce HC emissions, evaporated fuel from the fuel tank is routed through a charcoal canister to the intake manifold for combustion in the cylinders.

The ECM changes the duty signal sent to the purge VSV so that the intake amount of HC emissions is appropriate for driving conditions (engine load, engine speed, vehicle speed, etc.) after the engine is warmed up.

DTC No. DTC Detection Condition Trouble Area
P0443 The terminal voltage of the ECM output circuit does not correspond with the drive signals from the ECM to the purge VSV (1 trip detection logic).
·

Open or short in purge VSV circuit

·

Purge VSV

·

ECM



WIRING DIAGRAM

for Manual Transmission Models
A337230E26
0.656,3.823 1.271,4.021 0.615,0.198 10 false Battery 0.583,2.854 1.198,3.052 0.615,0.198 10 false P/I-B 1.458,2.427 3.135,2.865 1.677,0.438 10 false Integration Relay 0.708,0.875 1.323,1.073 0.615,0.198 10 false 1X 0.75,0.708 1.365,0.906 0.615,0.198 10 false 1 1.031,1.031 1.729,1.448 0.698,0.417 10 false EFI MAIN NO. 1 1.469,1.646 2.552,1.865 1.083,0.219 10 false EFI MAIN NO. 1 2.375,1.042 3.135,1.271 0.76,0.229 10 false EFI NO. 2 3.094,0.875 3.708,1.073 0.615,0.198 10 false 1S 3.125,0.698 3.74,0.896 0.615,0.198 10 false 1 3.073,1.375 3.677,1.552 0.604,0.177 10 false 1S 3.125,1.188 3.74,1.385 0.615,0.198 10 false 4 3.063,2.063 3.677,2.26 0.615,0.198 10 false 1S 3.094,1.875 3.708,2.073 0.615,0.198 10 false 8 6.083,3.719 6.573,4.031 0.49,0.313 10 false ECM 5.406,2.063 6.021,2.26 0.615,0.198 10 false A38 5.458,1.854 6.104,2.073 0.646,0.219 10 false 34 5.417,0.875 6.031,1.073 0.615,0.198 10 false C45 5.448,0.688 6.063,0.885 0.615,0.198 10 false 63 5.75,2.063 6.365,2.26 0.615,0.198 10 false MREL 5.75,0.792 6.365,0.99 0.615,0.198 10 false PRG 4.198,1.375 5.313,1.583 1.115,0.208 10 false Purge VSV 4.198,1.219 4.813,1.417 0.615,0.198 10 false C55 3.969,0.781 4.583,0.979 0.615,0.198 10 false 1 5.052,0.781 5.333,0.99 0.281,0.208 10 false 2


for Automatic Transmission Models
A337230E30
0.656,3.823 1.271,4.021 0.615,0.198 10 false Battery 0.583,2.854 1.198,3.052 0.615,0.198 10 false P/I-B 1.563,2.427 3.135,2.865 1.573,0.438 10 false Integration Relay 0.708,0.875 1.323,1.073 0.615,0.198 10 false 1X 0.75,0.708 1.365,0.906 0.615,0.198 10 false 1 1,1.031 1.729,1.406 0.729,0.375 10 false EFI MAIN NO. 1 1.563,1.656 2.594,1.885 1.031,0.229 10 false EFI MAIN NO. 1 2.375,1.042 3.135,1.271 0.76,0.229 10 false EFI NO. 2 3.094,0.875 3.708,1.073 0.615,0.198 10 false 1S 3.125,0.698 3.74,0.896 0.615,0.198 10 false 1 3.063,1.375 3.677,1.573 0.615,0.198 10 false 1S 3.125,1.188 3.74,1.385 0.615,0.198 10 false 4 3.063,2.063 3.677,2.26 0.615,0.198 10 false 1S 3.146,1.875 3.708,2.073 0.563,0.198 10 false 8 6.083,3.719 6.573,4.031 0.49,0.313 10 false ECM 5.406,2.063 6.021,2.26 0.615,0.198 10 false A38 5.49,1.865 6.167,2.063 0.677,0.198 10 false 6 5.417,0.875 6.031,1.073 0.615,0.198 10 false C45 5.448,0.688 6.063,0.885 0.615,0.198 10 false 82 5.75,2.063 6.365,2.26 0.615,0.198 10 false MREL 5.75,0.792 6.365,0.99 0.615,0.198 10 false PRG 4.177,1.385 5.448,1.792 1.271,0.406 10 false Purge VSV 4.177,1.229 4.792,1.427 0.615,0.198 10 false C55 3.948,0.771 4.167,0.99 0.219,0.219 10 false 1 5.052,0.76 5.333,0.969 0.281,0.208 10 false 2


CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR EVAP CONTROL)
a.
A200511E07
0.792,0.2 0.966,0.376 0.174,0.176 10 *a 2.484,0.2 2.668,0.353 0.184,0.153 10 *b

Connect the GTS to the DLC3.


b.

Remove the vacuum hose of the purge VSV from the charcoal canister.


c.

Start the engine and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.


e.

When the purge VSV is operated using the GTS, check whether the disconnected hose applies suction to your finger.

OK:
GTS Operation Specified Condition
VSV is ON Disconnected hose applies suction to finger
VSV is OFF Disconnected hose applies no suction to finger


Text in Illustration
*a VSV is ON
*b VSV is OFF



OK

NG

2.INSPECT PURGE VSV
2.INSPECT PURGE VSV

OK

3.INSPECT PURGE VSV (POWER SOURCE VOLTAGE)

NG

3.INSPECT PURGE VSV (POWER SOURCE VOLTAGE)
U162867E02
0.188,0.188 0.396,0.396 0.208,0.208 10 false *a 0.448,1.865 0.729,2.01 0.281,0.146 10 false C55

a.

Disconnect the purge VSV connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C55-1 - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Purge VSV)


c.

Reconnect the purge VSV connector.



OK

4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (PURGE VSV - INTEGRATION RELAY)
4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)
a.

Disconnect the purge VSV connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Manual Transmission Models
Tester Connection Condition Specified Condition
C55-2 - C45-63 (PRG) Always Below 1 Ω
C55-2 or C45-63 (PRG) - Body ground Always 10 kΩ or higher

for Automatic Transmission Models
Tester Connection Condition Specified Condition
C55-2 - C45-82 (PRG) Always Below 1 Ω
C55-2 or C45-82 (PRG) - Body ground Always 10 kΩ or higher



d.

Reconnect the purge VSV connector.


e.

Reconnect the ECM connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (PURGE VSV - INTEGRATION RELAY)
a.

Disconnect the purge VSV connector.


b.

Remove the integration relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C55-1 - 1S-1 Always Below 1 Ω
C55-1 or 1S-1 - Body ground Always 10 kΩ or higher



d.

Reconnect the purge VSV connector.


e.

Reinstall the integration relay.



OK

REPAIR OR REPLACE POWER SOURCE CIRCUIT COMPONENTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR