Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for RHD without Central Gateway ECU) › from 2017.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255538 CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU) U

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU)  TERMINALS OF ECU  


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Turn the ignition switch off before measuring the resistances between CAN main wires and between CAN branch wires.

·

Turn the ignition switch off before inspecting CAN wires for a ground short.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

This section describes the standard values for all CAN related components.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



JUNCTION CONNECTOR


a.

NO. 1 CAN JUNCTION CONNECTOR

U165469E01
0.123,0.087 0.348,0.257 0.225,0.170 10 *a 0.932,0.84 1.275,0.982 0.343,0.142 10 E133 1.676,0.519 2.245,0.662 0.569,0.144 10 CANH*b 1.711,1.133 2.280,1.277 0.569,0.144 10 CANL*b 1.898,1.317 2.468,1.460 0.569,0.144 10 CANL*c 2.454,1.386 2.646,1.386 2.646,1.386 2.834,0.999 false 2.063,1.573 2.632,1.716 0.569,0.144 10 CANL*d 3.128,1.564 3.697,1.707 0.569,0.144 10 CANL*e 2.073,0.195 2.643,0.338 0.569,0.144 10 CANH*d 1.814,0.352 2.384,0.496 0.569,0.144 10 CANH*c 2.343,0.03 2.913,0.174 0.569,0.144 10 CANH*e 4.298,0.366 4.867,0.509 0.569,0.144 10 CANH*h 4.834,0.634 5.403,0.778 0.569,0.144 10 CANH*i 3.597,0.034 4.167,0.177 0.569,0.144 10 CANH*f 4.138,0.197 4.707,0.340 0.569,0.144 10 CANH*g 4.294,1.24 4.863,1.383 0.569,0.144 10 CANL*h 4.865,1.107 5.434,1.250 0.569,0.144 10 CANL*i 4.17,1.402 4.739,1.546 0.569,0.144 10 CANL*g 3.91,1.614 4.480,1.757 0.569,0.144 10 CANL*f 3.928,0.839 4.177,0.424 4.177,0.424 4.275,0.424 false 3.419,0.844 3.486,0.098 3.486,0.098 3.584,0.098 false 2.412,0.418 2.604,0.418 2.604,0.418 2.834,0.847 false 2.629,0.271 2.87,0.271 2.87,0.271 3.014,0.836 false 2.916,0.096 3.158,0.096 3.158,0.096 3.233,0.831 false 3.737,0.826 3.912,0.269 3.912,0.269 4.126,0.269 false 3.928,1.007 4.177,1.295 4.177,1.295 4.275,1.295 false 3.419,1.003 3.781,1.684 3.781,1.684 3.879,1.684 false 2.609,0.839 2.364,0.595 2.364,0.595 2.266,0.595 false 2.609,1.007 2.364,1.198 2.364,1.198 2.266,1.198 false 2.454,1.386 2.646,1.386 2.646,1.386 2.834,0.999 false 2.599,1.633 2.841,1.633 2.841,1.633 3.014,1.01 false 3.114,1.628 2.988,1.628 2.988,1.628 3.233,1.015 false 3.737,1.02 3.923,1.468 3.923,1.468 4.137,1.468 false 4.806,0.697 4.665,0.697 4.665,0.697 4.507,0.837 false 4.518,1.005 4.721,1.177 4.721,1.177 4.833,1.177 false

Text in Illustration
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b for No. 2 CAN Junction Connector
*c for Main Body ECU (Multiplex Network Body ECU) *d for Master Cylinder Solenoid (Skid Control ECU)
*e for Headlight Leveling ECU Assembly *f
·

for Multi-media Module Receiver Assembly (for Multi-media Module Receiver Type)

·

for Option Connector (w/ Option Connector)


*g for Air Conditioning Amplifier Assembly *h for ECM
*i for Bus Buffer ECU (w/ Bus Buffer ECU) - -

No. 1 CAN Junction Connector Wiring Color Connect to
E133-1 (CANH) SB No. 2 CAN junction connector
E133-11 (CANL) W
E133-2 (CANH) G Main body ECU (multiplex network body ECU)
E133-12 (CANL) W
E133-3 (CANH) L Master cylinder solenoid (skid control ECU)
E133-13 (CANL) W
E133-4 (CANH) LG Headlight leveling ECU assembly
E133-14 (CANL) B
E133-5 (CANH) G
·

Multi-media module receiver assembly*1

·

Option connector*2


E133-15 (CANL) GR
E133-6 (CANH) G Air conditioning amplifier assembly
E133-16 (CANL) W
E133-7 (CANH) V ECM
E133-17 (CANL) W
E133-10 (CANH) BE Bus buffer ECU*3
E133-20 (CANL) W

*1: for Multi-media Module Receiver Type

*2: w/ Option Connector

*3: w/ Bus Buffer ECU



b.

NO. 2 CAN JUNCTION CONNECTOR

U165470E01
0.123,0.087 0.348,0.257 0.225,0.170 10 *a 0.932,0.84 1.275,0.982 0.343,0.142 10 E135 1.676,0.519 2.245,0.662 0.569,0.144 10 CANH*b 1.711,1.133 2.280,1.277 0.569,0.144 10 CANL*b 1.797,1.317 2.366,1.460 0.569,0.144 10 CANL*c 2.352,1.386 2.545,1.386 2.545,1.386 2.834,0.999 false 1.93,1.478 2.499,1.622 0.569,0.144 10 CANL*d 2.896,1.564 3.466,1.707 0.569,0.144 10 CANL*e 2.073,0.195 2.643,0.338 0.569,0.144 10 CANH*d 1.814,0.352 2.384,0.496 0.569,0.144 10 CANH*c 2.343,0.03 2.913,0.174 0.569,0.144 10 CANH*e 3.81,0.332 4.379,0.475 0.569,0.144 10 CANH*h 4.725,0.217 5.295,0.361 0.569,0.144 10 CANH*i 3.391,0 3.961,0.144 0.569,0.144 10 CANH*f 3.737,0.153 4.306,0.296 0.569,0.144 10 CANH*g 4.334,1.604 4.904,1.747 0.569,0.144 10 CANL*h 4.606,1.25 5.175,1.394 0.569,0.144 10 CANL*j 4.49,1.411 5.060,1.555 0.569,0.144 10 CANL*i 3.484,1.265 4.053,1.409 0.569,0.144 10 CANL*g 3.138,1.412 3.708,1.556 0.569,0.144 10 CANL*f 3.928,0.839 3.689,0.39 3.689,0.39 3.788,0.39 false 3.419,0.844 3.279,0.049 3.279,0.049 3.378,0.049 false 2.412,0.418 2.604,0.418 2.604,0.418 2.834,0.847 false 2.629,0.271 2.87,0.271 2.87,0.271 3.014,0.836 false 2.916,0.096 3.158,0.096 3.158,0.096 3.233,0.831 false 3.737,0.826 3.511,0.225 3.511,0.225 3.725,0.225 false 3.975,1.009 4.217,1.659 4.217,1.659 4.315,1.659 false 3.419,1.003 3.009,1.483 3.009,1.483 3.107,1.483 false 4.799,0.41 5.368,0.554 0.569,0.144 10 CANH*j 4.356,0.839 4.692,0.472 4.692,0.472 4.79,0.472 false 4.356,1.007 4.491,1.325 4.491,1.325 4.589,1.325 false 2.609,0.839 2.364,0.595 2.364,0.595 2.266,0.595 false 2.609,1.007 2.364,1.198 2.364,1.198 2.266,1.198 false 2.352,1.386 2.545,1.386 2.545,1.386 2.834,0.999 false 2.466,1.539 2.708,1.539 2.708,1.539 3.014,1.01 false 2.883,1.628 2.757,1.628 2.757,1.628 3.233,1.015 false 3.671,1.02 3.237,1.33 3.237,1.33 3.451,1.33 false 4.697,0.28 4.557,0.28 4.557,0.28 4.165,0.837 false 4.176,1.005 4.347,1.481 4.347,1.481 4.459,1.481 false 4.843,0.643 5.412,0.787 0.569,0.144 10 CANH*k 4.54,0.847 4.736,0.706 4.736,0.706 4.834,0.706 false 4.83,1.114 5.400,1.258 0.569,0.144 10 CANL*k 4.571,0.998 4.724,1.176 4.724,1.176 4.822,1.176 false

Text in Illustration
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b for No. 1 CAN Junction Connector
*c for 4WD Control ECU *d for Power Steering ECU Assembly (w/ Variable Flow Control Solenoid Valve)
*e for Airbag Sensor Assembly *f for Tire Pressure Warning ECU (w/ Tire Pressure Warning System)
*g for Steering Sensor *h for Combination Meter Assembly
*i for Certification ECU (Smart Key ECU Assembly) (w/ Entry and Start System) *j for Steering control ECU (w/ Variable Gear Ratio Steering System)
*k for DLC3 - -

No. 2 CAN Junction Connector Wiring Color Connect to
E135-1 (CANH) SB No. 1 CAN junction connector
E135-11 (CANL) W
E135-2 (CANH) P 4WD control ECU
E135-12 (CANL) W
E135-3 (CANH) LG Power steering ECU assembly*1
E135-13 (CANL) W
E135-4 (CANH) GR Airbag sensor assembly
E135-14 (CANL) W
E135-5 (CANH) R Tire pressure warning ECU*2
E135-15 (CANL) W
E135-6 (CANH) GR Steering sensor
E135-16 (CANL) W
E135-7 (CANH) BE Combination meter assembly
E135-17 (CANL) W
E135-8 (CANH) B Certification ECU (smart key ECU assembly)*3
E135-18 (CANL) W
E135-9 (CANH) R Steering control ECU*4
E135-19 (CANL) W
E135-10 (CANH) LG DLC3
E135-20 (CANL) W

*1: w/ Variable Flow Control Solenoid Valve

*2: w/ Tire Pressure Warning System

*3: w/ Entry and Start System

*4: w/ Variable Gear Ratio Steering System



c.

NO. 7 CAN JUNCTION CONNECTOR

U165571E01
0.09,0.077 0.392,0.330 0.302,0.253 10 *a 2.354,1.414 2.705,1.554 0.351,0.140 10 E134 4.53,1.263 5.105,1.402 0.575,0.139 10 CANH*b 4.536,1.783 5.111,1.921 0.575,0.139 10 CANL*b 4.475,1.989 5.050,2.128 0.575,0.139 10 CANL*c 4.521,1.03 5.096,1.168 0.575,0.139 10 CANH*c 4.129,1.675 4.344,1.848 4.344,1.848 4.524,1.848 false 4.459,2.061 4.247,2.061 4.247,2.061 4.017,1.675 false 4.129,1.47 4.338,1.326 4.338,1.326 4.518,1.326 false 4.495,1.09 4.284,1.09 4.284,1.09 4.017,1.47 false 3.908,1.675 4.166,2.292 4.166,2.292 4.33,2.292 false 3.908,1.462 4.222,0.845 4.222,0.845 4.386,0.845 false 4.354,2.224 4.929,2.363 0.575,0.139 10 CANL*d 4.404,0.78 4.979,0.918 0.575,0.139 10 CANH*d

Text in Illustration
*a Rear view of wire harness connector
(to No. 7 CAN Junction Connector)
*b for No. 8 CAN Junction Connector
*c for Main Body ECU (Multiplex Network Body ECU) *d for Outer Mirror Control ECU Assembly LH (w/ Memory)

No. 7 CAN Junction Connector Wiring Color Connect to
E134-1 (CANH) W No. 8 CAN junction connector
E134-12 (CANL) L
E134-2 (CANH) GR Main body ECU (multiplex network body ECU)
E134-13 (CANL) L
E134-3 (CANH) BE Outer mirror control ECU assembly LH*
E134-14 (CANL) L

*: w/ Memory



d.

NO. 8 CAN JUNCTION CONNECTOR

U165572E01
0.09,0.077 0.392,0.330 0.302,0.253 10 *a 2.354,1.414 2.705,1.554 0.351,0.140 10 E136 4.53,1.263 5.105,1.402 0.575,0.139 10 CANH*b 4.536,1.783 5.111,1.921 0.575,0.139 10 CANL*b 4.475,1.989 5.050,2.128 0.575,0.139 10 CANL*c 4.521,1.03 5.096,1.168 0.575,0.139 10 CANH*c 4.129,1.675 4.344,1.848 4.344,1.848 4.524,1.848 false 4.459,2.061 4.247,2.061 4.247,2.061 4.017,1.675 false 4.129,1.47 4.338,1.326 4.338,1.326 4.518,1.326 false 4.495,1.09 4.284,1.09 4.284,1.09 4.017,1.47 false 3.908,1.675 4.222,2.292 4.222,2.292 4.386,2.292 false 4.358,2.506 4.134,2.506 4.134,2.506 3.807,1.675 false 3.693,1.675 3.886,2.705 3.886,2.705 4.054,2.705 false 3.908,1.462 4.222,0.845 4.222,0.845 4.386,0.845 false 4.358,0.639 4.134,0.639 4.134,0.639 3.807,1.47 false 3.693,1.455 3.886,0.397 3.886,0.397 4.054,0.397 false 4.41,2.224 4.985,2.363 0.575,0.139 10 CANL*d 4.381,2.445 4.955,2.583 0.575,0.139 10 CANL*e 4.065,2.63 4.640,2.769 0.575,0.139 10 CANL*f 4.404,0.78 4.979,0.918 0.575,0.139 10 CANH*d 4.395,0.574 4.969,0.713 0.575,0.139 10 CANH*e 4.086,0.329 4.661,0.468 0.575,0.139 10 CANH*f

Text in Illustration
*a Rear view of wire harness connector
(to No. 8 CAN Junction Connector)
*b for No. 7 CAN Junction Connector
*c for No. 9 CAN Junction Connector *d for Outer Mirror Control ECU Assembly RH (w/ Memory)
*e for Power Seat Switch Assembly (w/ Memory) *f for Multiplex Tilt and Telescopic ECU (w/ Power Tilt and Power Telescopic Steering Column System)

No. 8 CAN Junction Connector Wiring Color Connect to
E136-1 (CANH) W No. 7 CAN junction connector
E136-12 (CANL) L
E136-2 (CANH) W No. 9 CAN junction connector
E136-13 (CANL) L
E136-3 (CANH) LG Outer mirror control ECU assembly RH*1
E136-14 (CANL) L
E136-4 (CANH) V Power seat switch assembly*1
E136-15 (CANL) L
E136-5 (CANH) P Multiplex Tilt and Telescopic ECU*2
E136-16 (CANL) L

*1: w/ Memory

*2: w/ Power Tilt and Power Telescopic Steering Column System



e.

NO. 9 CAN JUNCTION CONNECTOR

U165573E01
0.09,0.077 0.392,0.330 0.302,0.253 10 *a 2.377,1.414 2.637,1.554 0.261,0.140 10 L71 4.53,1.263 5.105,1.402 0.575,0.139 10 CANH*b 4.536,1.783 5.111,1.921 0.575,0.139 10 CANL*b 4.475,1.989 5.050,2.128 0.575,0.139 10 CANL*c 4.521,1.03 5.096,1.168 0.575,0.139 10 CANH*c 4.129,1.675 4.344,1.848 4.344,1.848 4.524,1.848 false 4.459,2.061 4.247,2.061 4.247,2.061 4.017,1.675 false 4.129,1.47 4.338,1.326 4.338,1.326 4.518,1.326 false 4.495,1.09 4.284,1.09 4.284,1.09 4.017,1.47 false 3.908,1.675 4.222,2.292 4.222,2.292 4.386,2.292 false 4.358,2.506 4.134,2.506 4.134,2.506 3.807,1.675 false 3.908,1.462 4.222,0.845 4.222,0.845 4.386,0.845 false 4.358,0.639 4.134,0.639 4.134,0.639 3.807,1.47 false 4.41,2.224 4.985,2.363 0.575,0.139 10 CANL*d 4.381,2.445 4.955,2.583 0.575,0.139 10 CANL*e 4.404,0.78 4.979,0.918 0.575,0.139 10 CANH*d 4.395,0.574 4.969,0.713 0.575,0.139 10 CANH*e

Text in Illustration
*a Rear view of wire harness connector
(to No. 9 CAN Junction Connector)
*b for No. 8 CAN Junction Connector
*c for No. 3 CAN Junction Terminal *d for Power Back Door Unit Assembly (Power Back Door ECU) (w/ Power Back Door System)
*e for No. 2 Main Body ECU (w/ Tail Gate Closer System) - -

No. 9 CAN Junction Connector Wiring Color Connect to
L71-1 (CANH) W No. 8 CAN junction connector
L71-12 (CANL) L
L71-2 (CANH) W No. 3 CAN junction terminal
L71-13 (CANL) L
L71-3 (CANH) V Power back door unit assembly (power back door ECU)*1
L71-14 (CANL) L
L71-4 (CANH) LG No. 2 main body ECU*2
L71-15 (CANL) L

*1: w/ Power Back Door System

*2: w/ Tail Gate Closer System



f.
U164974E02
1.781,0.146 1.615,0.146 1.615,0.146 1.375,0.875 false 2.219,0.417 2.073,0.417 2.073,0.417 1.729,0.854 false 1.833,0.052 2.458,0.229 0.625,0.177 10 false CANH 0.542,0.906 0.885,1.083 0.344,0.177 10 false L69 0.104,0 0.313,0.177 0.208,0.177 10 false *a 2.281,0.313 2.844,0.51 0.563,0.198 10 false CANL

NO. 3 CAN JUNCTION TERMINAL

Text in Illustration
*a Rear view of wire harness connector
(to No. 3 CAN Junction Terminal)

No. 3 CAN Junction Terminal Wiring Color Connect to
L69-3 (CANH) W No. 9 CAN junction connector
L69-2 (CANL) L



CHECK DLC3


a.
U156301E04
1.594,0.896 1.396,0.406 1.396,0.406 1.271,0.406 false 1.948,0.896 2.135,0.406 2.135,0.406 2.271,0.406 false 2.333,1.469 2.479,1.896 2.479,1.896 2.615,1.896 false 1.969,1.469 1.823,1.896 1.823,1.896 1.688,1.896 false 0.052,0 0.219,0.188 0.167,0.188 10 false *a 2.333,0.323 2.99,0.531 0.656,0.208 10 false CANH 0.948,0.323 1.417,0.531 0.469,0.208 10 false CG 1.229,1.823 1.771,2.021 0.542,0.198 10 false CANL 2.656,1.792 3.125,1.99 0.469,0.198 10 false BAT 0.313,0.385 0.708,0.583 0.396,0.198 10 false E22

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and CAN branch wire.

Text in Illustration
*a Front view of DLC3


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E22-6 (CANH) - E22-14 (CANL) LG - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E22-6 (CANH) - E22-4 (CG) LG - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E22-14 (CANL) - E22-4 (CG) W - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E22-6 (CANH) - E22-16 (BAT) LG - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E22-14 (CANL) - E22-16 (BAT) W - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK ECM


U164556E02
4.594,1.719 4.063,2.313 4.063,2.313 3.99,2.313 false 4.594,1.833 4.469,2.552 4.469,2.552 4.396,2.552 false 4.594,1.094 4.333,0.656 4.333,0.656 4.271,0.656 false 4.719,1.094 4.542,0.417 4.542,0.417 4.479,0.417 false 0.229,0 0.542,0.208 0.313,0.208 10 false *a 3.396,2.229 4.094,2.417 0.698,0.188 10 false CANL*B 3.802,2.469 4.542,2.656 0.74,0.188 10 false CANH*B 3.688,0.583 4.375,0.802 0.688,0.219 10 false CANL*A 3.885,0.333 4.615,0.521 0.729,0.188 10 false CANH*A 5.156,0.542 5.583,0.74 0.427,0.198 10 false A52

Text in Illustration
*A for 1UR-FE *B for 1VD-FTV
*a Component without harness connected
(ECM)
- -

a.

Disconnect the ECM connectors.

U165108E01
2.008,0.608 2.275,0.750 0.267,0.142 10 A52 6.546,1.44 6.827,1.582 0.281,0.142 10 C46 0.099,0.078 0.364,0.220 0.265,0.142 10 *a 1.498,0.822 1.564,0.822 1.564,0.822 1.884,1.199 false 0.982,0.748 1.501,0.890 0.519,0.142 10 BATT*A 2.781,1.197 3.068,0.791 3.068,0.791 3.173,0.791 false 3.187,0.723 3.895,0.865 0.708,0.142 10 CANL*A 2.697,1.197 2.755,0.555 2.755,0.555 2.86,0.555 false 2.874,0.487 3.582,0.629 0.708,0.142 10 CANH*A 4.984,2.183 5.061,2.183 5.061,2.183 5.229,1.682 false 4.771,2.123 5.035,2.265 0.264,0.142 10 E1 3.337,2.105 3.882,2.247 0.546,0.142 10 CANL*B 2.773,1.647 3.219,2.177 3.219,2.177 3.326,2.177 false 3.047,2.346 3.609,2.488 0.562,0.142 10 CANH*B 2.771,1.727 2.929,2.418 2.929,2.418 3.037,2.418 false 1.162,1.076 1.228,1.076 1.228,1.076 1.87,1.344 false 0.646,1.003 1.165,1.145 0.519,0.142 10 BATT*B

Text in Illustration
*A for 1UR-FE *B for 1VD-FTV
*a Front view of wire harness connector
(to ECM)
- -


b.

Measure the resistance according to the value(s) in the table below.

for 1UR-FE
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
A52-10 (CANH) - A52-11 (CANL) V - W Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A52-10 (CANH) - C46-81 (E1) V - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
A52-11 (CANL) - C46-81 (E1) W - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
A52-10 (CANH) - A52-1 (BATT) V - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A52-11 (CANL) - A52-1 (BATT) W - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher

for 1VD-FTV
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
A52-41 (CANH) - A52-49 (CANL) V - W Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A52-41 (CANH) - C46-81 (E1) V - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
A52-49 (CANL) - C46-81 (E1) W - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
A52-41 (CANH) - A52-20 (BATT) V - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A52-49 (CANL) - A52-20 (BATT) W - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK MASTER CYLINDER SOLENOID (SKID CONTROL ECU)


U164487E02
2.896,0.906 2.615,0.448 2.615,0.448 2.5,0.448 false 2.594,0.167 2.74,0.167 2.74,0.167 2.906,0.677 false 0.094,0.073 0.51,0.292 0.417,0.219 10 false *a 1.031,0.906 1.479,1.146 0.448,0.24 10 false A24 2.135,0.083 2.667,0.271 0.531,0.188 10 false CANH 2.073,0.354 2.604,0.552 0.531,0.198 10 false CANL

Text in Illustration
*a Component without harness connected
(Master Cylinder Solenoid [Skid Control ECU])
- -

a.
U156452E01
0.1,0.106 0.286,0.278 0.185,0.172 10 *a 1.266,0.254 1.538,0.391 0.272,0.137 10 A24 2.56,0.23 3.065,0.366 0.505,0.137 10 CANH 2.638,0.556 3.142,0.693 0.505,0.137 10 CANL 0.127,0.407 0.632,0.544 0.505,0.137 10 +BM1 0.028,0.678 0.533,0.815 0.505,0.137 10 GND1 2.178,1.099 2.464,0.626 2.464,0.626 2.605,0.626 false 2.519,0.312 2.343,0.312 2.343,0.312 2.143,1.014 false 0.994,1.013 0.783,0.497 0.783,0.497 0.594,0.497 false 0.517,0.738 0.633,0.738 0.633,0.738 0.846,1.013 false

Disconnect the master cylinder solenoid (skid control ECU) connector.

Text in Illustration
*a Front view of wire harness connector
(to Master Cylinder Solenoid [Skid Control ECU])


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
A24-11 (CANH) - A24-25 (CANL) L - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A24-11 (CANH) - A24-1 (GND1) L - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
A24-25 (CANL) - A24-1 (GND1) W - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
A24-11 (CANH) - A24-2 (+BM1) L - B Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A24-25 (CANL) - A24-2 (+BM1) W - B Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (for Automatic Air Conditioning System)


U156293E04
4.063,0.833 4.354,0.115 4.354,0.115 4.521,0.115 false 4.167,0.833 4.563,0.323 4.563,0.323 4.729,0.323 false 0.073,0.052 0.542,0.281 0.469,0.229 10 false *a 4.781,0.25 5.323,0.427 0.542,0.177 10 false CANH 4.563,0.031 5.198,0.24 0.635,0.208 10 false CANL 4.76,0.927 5.125,1.135 0.365,0.208 10 false E35

Text in Illustration
*a Component without harness connected
(Air Conditioning Amplifier Assembly)
- -

a.
U156515E04
2.115,3.208 2.313,3.104 2.313,3.104 2.427,3.104 false 0.948,3.01 1.208,3.01 1.208,3.01 1.427,3.208 false 1.865,1.063 2.292,0.781 2.292,0.781 2.542,0.781 false 2.365,0.406 2.198,0.406 2.198,0.406 1.75,1.052 false 0.104,0.052 0.354,0.25 0.25,0.198 10 false *a 0.51,3.313 0.938,3.521 0.427,0.208 10 false E36 2.469,3.01 3.021,3.208 0.552,0.198 10 false GND 0.604,2.917 1.01,3.104 0.406,0.188 10 false +B1 0.594,1.198 0.958,1.438 0.365,0.24 10 false E35 2.583,0.688 3.125,0.885 0.542,0.198 10 false CANH 2.406,0.323 2.969,0.531 0.563,0.208 10 false CANL

Disconnect the air conditioning amplifier assembly connectors.

Text in Illustration
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Condition Specified Condition
E35-3 (CANH) - E35-4 (CANL) G - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E35-3 (CANH) - E36-1 (GND) G - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
E35-4 (CANL) - E36-1 (GND) W - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
E35-3 (CANH) - E36-6 (+B1) G - LG Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E35-4 (CANL) - E36-6 (+B1) W - LG Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (for Manual Air Conditioning System)


U164986E01
3.097,0.612 3.523,0.775 0.425,0.163 10 CANL 3.404,0.403 3.830,0.566 0.425,0.163 10 CANH 4.296,0.494 4.571,0.637 0.275,0.143 10 E81 3.902,1.142 3.594,0.678 3.594,0.678 3.498,0.678 false 4.025,1.144 3.904,0.474 3.904,0.474 3.832,0.474 false 0.085,0.071 0.510,0.233 0.425,0.163 10 *a

Text in Illustration
*a Component without harness connected
(Air Conditioning Amplifier Assembly)
- -

a.
U165133E01
0.897,0.165 1.316,0.302 0.419,0.137 10 CANH 0.074,0.061 0.262,0.198 0.188,0.137 10 *a 2.885,1.372 3.171,1.510 0.287,0.137 10 +B1 2.567,1.264 2.732,1.454 2.732,1.454 2.86,1.454 false 0.536,0.431 0.945,0.569 0.409,0.137 10 CANL 0.398,0.635 0.808,0.772 0.409,0.137 10 GND 1.48,1.112 0.941,0.717 0.941,0.717 0.813,0.717 false 1.642,1.103 1.133,0.498 1.133,0.498 1.006,0.498 false 1.726,1.103 1.584,0.247 1.584,0.247 1.405,0.247 false 2.413,0.254 2.678,0.396 0.265,0.141 10 E81

Disconnect the air conditioning amplifier assembly connector.

Text in Illustration
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Condition Specified Condition
E81-11 (CANH) - E81-12 (CANL) G - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E81-11 (CANH) - E81-14 (GND) G - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
E81-12 (CANL) - E81-14 (GND) W - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
E81-11 (CANH) - E81-21 (+B1) G - LG Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E81-12 (CANL) - E81-21 (+B1) W - LG Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK COWL SIDE JUNCTION BLOCK LH AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


U166538E02
1.625,0.635 1.625,0.396 1.625,0.396 1.708,0.396 false 1.615,1.458 1.865,1.458 false 1.615,1.813 1.865,1.813 false 2.438,4.021 2.896,3.563 2.896,3.563 3.063,3.563 false 2.854,3.313 2.688,3.313 2.688,3.313 2.344,4.021 false 4.823,4.021 5.396,3.479 5.396,3.479 5.51,3.479 false 5.344,3.271 5.198,3.271 5.198,3.271 4.74,4.021 false 0.875,1.26 1.25,1.458 0.375,0.198 10 false 2K 1.74,0.323 2.083,0.521 0.344,0.198 10 false *1 0.104,0.104 0.542,0.354 0.438,0.25 12 false *A 1.917,1.375 2.792,1.583 0.875,0.208 10 false E118 1.917,1.729 2.781,1.969 0.865,0.24 10 false E117 0.875,1.813 1.198,2.042 0.323,0.229 10 false 2H 0.885,2.229 1.229,2.417 0.344,0.188 10 false 2G 2.885,3.219 3.667,3.438 0.781,0.219 10 false CANN*B 3.104,3.469 3.854,3.708 0.75,0.24 10 false CANP*B 0.938,2.438 1.292,2.677 0.354,0.24 10 false 2F 3.76,0.99 4.094,1.198 0.333,0.208 10 false A 5.865,1.115 6.188,1.323 0.323,0.208 10 false 2J 5.875,1.781 6.198,1.979 0.323,0.198 10 false 2I 2,3.24 2.427,3.458 0.427,0.219 10 false E117 4.49,3.281 4.885,3.531 0.396,0.25 10 false E118 5.552,3.396 6.375,3.625 0.823,0.229 10 false CANL*A 5.385,3.167 6.177,3.365 0.792,0.198 10 false CANH*A 1.813,4.667 2.063,4.896 0.25,0.229 10 false 2I 5.594,4.667 5.938,4.885 0.344,0.219 10 false 2J 1.24,6.167 1.531,6.365 0.292,0.198 10 false 2H 3.781,6.167 4.135,6.375 0.354,0.208 10 false 2K 5.438,6.323 5.823,6.51 0.385,0.188 10 false 2G 6.438,6.323 6.75,6.542 0.313,0.219 10 false 2F 3.542,7.771 3.74,8.01 0.198,0.24 10 false A

Text in Illustration
*A Main Body ECU (Multiplex Network Body ECU) with 2 Connectors *B V Bus
*C Sub Bus 1 - -
*1 Main Body ECU (Multiplex Network Body ECU) - -

U166539E02
1.625,0.635 1.625,0.396 1.625,0.396 1.708,0.396 false 1.615,1.135 1.865,1.135 false 1.615,1.458 1.865,1.458 false 1.615,1.823 1.865,1.823 false 1.667,4.01 2.125,3.552 2.125,3.552 2.292,3.552 false 2.104,3.313 1.938,3.313 1.938,3.313 1.563,4.021 false 3.635,4.042 3.865,4.375 3.865,4.375 3.979,4.375 false 3.833,4.542 3.688,4.542 3.688,4.542 3.552,4.052 false 0.875,1.26 1.208,1.5 0.333,0.24 10 false 2K 1.906,1.052 2.792,1.25 0.885,0.198 10 false E137 1.74,0.26 2.094,0.479 0.354,0.219 10 false *1 0.104,0.104 0.542,0.354 0.438,0.25 12 false *A 1.906,1.375 2.781,1.646 0.875,0.271 10 false E118 1.906,1.75 2.771,1.979 0.865,0.229 10 false E117 0.875,1.802 1.25,2.021 0.375,0.219 10 false 2H 0.906,2.219 1.344,2.448 0.438,0.229 10 false 2G 2.146,3.219 2.865,3.438 0.719,0.219 10 false CANN*C 2.344,3.458 3.052,3.667 0.708,0.208 10 false CANP*C 0.938,2.438 1.333,2.635 0.396,0.198 10 false 2F 3.75,0.958 4.083,1.177 0.333,0.219 10 false A 5.865,1.135 6.219,1.354 0.354,0.219 10 false 2J 5.865,1.771 6.281,2.031 0.417,0.26 10 false 2I 1.333,3.24 1.771,3.479 0.438,0.24 10 false E117 3.604,3.24 4.083,3.469 0.479,0.229 10 false E118 5.719,3.24 6.177,3.479 0.458,0.24 10 false E137 4.021,4.292 4.813,4.49 0.792,0.198 10 false CANL*B 3.875,4.469 4.594,4.698 0.719,0.229 10 false CANH*B 1.813,4.667 2.063,4.927 0.25,0.26 10 false 2I 5.594,4.667 5.896,4.917 0.302,0.25 10 false 2J 1.25,6.167 1.542,6.406 0.292,0.24 10 false 2H 3.792,6.177 4.26,6.448 0.469,0.271 10 false 2K 5.438,6.313 5.781,6.542 0.344,0.229 10 false 2G 6.438,6.323 6.76,6.531 0.323,0.208 10 false 2F 3.531,7.781 3.865,8.104 0.333,0.323 10 false A

Text in Illustration
*A Main Body ECU (Multiplex Network Body ECU) with 3 Connectors *B V Bus
*C Sub Bus 1 - -
*1 Main Body ECU (Multiplex Network Body ECU) - -

a.

Remove the main body ECU (multiplex network body ECU) from the cowl side junction block LH (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL).

U165263E01
0.145,0.15 0.429,0.295 0.284,0.145 10 *a 4.283,0.15 4.566,0.295 0.284,0.145 10 *b 1.039,0.561 1.388,0.706 0.349,0.145 10 E118 2.772,0.561 3.120,0.706 0.349,0.145 10 E117 5.589,0.859 5.711,1.004 0.122,0.145 10 A 1.115,1.384 0.957,2.08 0.957,2.08 0.766,2.08 false 0.663,1.824 0.803,1.824 0.803,1.824 1.051,1.385 false 3.035,1.405 3.299,2.034 3.299,2.034 3.49,2.034 false 3.635,1.76 3.495,1.76 3.495,1.76 3.099,1.405 false 6.707,1.469 6.522,1.181 6.522,1.181 6.368,1.181 false 5.244,1.483 5.072,1.745 5.072,1.745 4.904,1.745 false 0.189,2.012 0.937,2.150 0.748,0.139 10 CANL*A 0.088,1.756 0.835,1.894 0.748,0.139 10 CANH*A 3.654,1.696 4.402,1.834 0.748,0.139 10 CANP*B 4.484,1.679 4.898,1.817 0.413,0.139 10 GND1 3.514,1.972 4.262,2.110 0.748,0.139 10 CANN*B 5.951,1.111 6.369,1.250 0.418,0.139 10 BECU

Text in Illustration
*A V Bus *B Sub Bus 1
*a Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])
*b Front view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])


b.

Reconnect the cowl side junction block LH connectors.


c.

Measure the resistance according to the value(s) in the table below.

V Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E118-14 (CANH) - E118-13 (CANL) G - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E118-14 (CANH) - A-11 (GND1) G - None Cable disconnected from negative (-) battery terminal 200 Ω or higher
E118-13 (CANL) - A-11 (GND1) W - None Cable disconnected from negative (-) battery terminal 200 Ω or higher
E118-14 (CANH) - A-31 (BECU) G - None Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E118-13 (CANL) - A-31 (BECU) W - None Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Sub Bus 1
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E117-9 (CANP) - E117-10 (CANN) GR - L Cable disconnected from negative (-) battery terminal 108 to 132 Ω
E117-9 (CANP) - A-11 (GND1) GR - None Cable disconnected from negative (-) battery terminal 200 Ω or higher
E117-10 (CANN) - A-11 (GND1) L - None Cable disconnected from negative (-) battery terminal 200 Ω or higher
E117-9 (CANP) - A-31 (BECU) GR - None Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E117-10 (CANN) - A-31 (BECU) L - None Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK COMBINATION METER ASSEMBLY


U166092E01
3.444,0.282 3.788,0.423 0.343,0.141 10 E119 2.105,1.295 1.807,1.186 1.807,1.186 1.671,1.186 false 2.312,1.277 2.081,0.36 2.081,0.36 1.947,0.36 false 1.533,0.289 1.949,0.430 0.416,0.141 10 CANH 1.259,1.126 1.676,1.267 0.416,0.141 10 CANL 0.107,0.072 0.523,0.213 0.416,0.141 10 *a

Text in Illustration
*a Component without harness connected
(Combination Meter Assembly)
- -

a.
U165132E01
0.252,1.752 0.671,1.889 0.419,0.137 10 CANH 0.074,0.061 0.262,0.198 0.188,0.137 10 *a 2.945,1.372 3.201,1.510 0.257,0.137 10 B 2.567,1.264 2.792,1.454 2.792,1.454 2.92,1.454 false 0.14,1.372 0.550,1.510 0.409,0.137 10 CANL 0.978,1.264 0.752,1.454 0.752,1.454 0.624,1.454 false 0.364,0.862 0.773,1.000 0.409,0.137 10 ET 0.978,1.104 0.752,0.945 0.752,0.945 0.624,0.945 false 1.061,1.264 0.939,1.845 0.939,1.845 0.76,1.845 false 1.578,0.223 1.922,0.364 0.343,0.141 10 E119

Disconnect the combination meter assembly connector.

Text in Illustration
*a Rear view of wire harness connector
(to Combination Meter Assembly)


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E119-39 (CANH) - E119-40 (CANL) BE - W Cable disconnected from negative (-) battery terminal 108 to 132 Ω
E119-39 (CANH) - E119-20 (ET) BE - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
E119-40 (CANL) - E119-20 (ET) W - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
E119-39 (CANH) - E119-21 (B) BE - V Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E119-40 (CANL) - E119-21 (B) W - V Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK AIRBAG SENSOR ASSEMBLY


U156197E01
4.28,0.722 4.084,0.722 4.084,0.722 3.678,1.328 false 3.782,1.606 4.059,2.021 4.059,2.021 4.217,2.021 false 3.254,0.625 3.522,0.762 0.268,0.137 10 E47 0.11,0.09 0.384,0.227 0.274,0.137 10 *a 4.318,0.652 4.752,0.789 0.435,0.137 10 CANH 4.234,1.961 4.748,2.098 0.514,0.137 10 CANL

Text in Illustration
*a Component without harness connected
(Airbag Sensor Assembly)
- -

a.
U156279E01
0.083,0.054 0.440,0.467 0.357,0.413 10 *a 0.083,1.975 0.440,2.388 0.357,0.413 10 *b 2.568,3.094 2.991,3.232 0.423,0.139 10 BAT 0.393,2.618 0.667,2.764 0.274,0.145 10 E22 0.482,0.946 0.756,1.091 0.274,0.145 10 E47 2.241,2.935 2.392,3.172 2.392,3.172 2.524,3.172 false 2.565,0.526 2.988,0.664 0.423,0.139 10 CANH 2.075,1.307 2.297,1.525 2.297,1.525 2.447,1.525 false 1.98,0.999 2.385,0.599 2.385,0.599 2.535,0.599 false 2.464,1.452 2.888,1.590 0.423,0.139 10 CANL 1.77,1.307 1.996,1.785 1.996,1.785 2.146,1.785 false 2.163,1.712 2.587,1.850 0.423,0.139 10 E1

Disconnect the airbag sensor assembly connector.

Text in Illustration
*a Rear view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of DLC3


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E47-13 (CANH) - E47-22 (CANL) GR - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E47-13 (CANH) - E47-25 (E1) GR - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
E47-22 (CANL) - E47-25 (E1) W - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
E47-13 (CANH) - E22-16 (BAT) GR - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E47-22 (CANL) - E22-16 (BAT) W - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY (for Multi-media Module Receiver Type)


U166548E01
1.854,0.795 2.113,0.933 0.259,0.138 10 F77 0.087,0.135 0.347,0.273 0.259,0.138 10 *a 3.04,1.445 3.364,1.131 3.364,1.131 3.525,1.131 false 3.31,0.9 3.11,0.9 3.11,0.9 2.941,1.442 false 3.318,0.842 3.880,0.980 0.563,0.138 10 CANL 3.544,1.068 4.107,1.206 0.563,0.138 10 CANH

Text in Illustration
*a Component without harness connected
(Multi-media Module Receiver Assembly)
- -

a.
U165484E01
0.454,1.11 0.537,1.989 0.537,1.989 0.709,1.989 false 2.81,0.591 2.682,0.591 2.682,0.591 2.842,1.02 false 0.916,1.741 0.787,1.741 0.787,1.741 0.551,1.11 false 0.939,1.664 1.361,1.801 0.422,0.137 10 CANL 0.738,1.915 1.160,2.052 0.422,0.137 10 CANH 0.054,0.044 0.477,0.182 0.422,0.137 10 *a 1.593,0.377 1.853,0.514 0.260,0.137 10 F77 2.836,0.51 3.105,0.647 0.269,0.137 10 +B1 2.476,1.787 2.348,1.787 2.348,1.787 2.106,1.097 false 2.499,1.71 2.921,1.847 0.422,0.137 10 GND1

Disconnect the multi-media module receiver assembly connector.

Text in Illustration
*a Front view of wire harness connector
(to Multi-media Module Receiver Assembly)


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F77-1 (CANH) - F77-2 (CANL) G - GR Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F77-1 (CANH) - F77-12 (GND1) G - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
F77-2 (CANL) - F77-12 (GND1) GR - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
F77-1 (CANH) - F77-17 (+B1) G - V Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F77-2 (CANL) - F77-17 (+B1) GR - V Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK STEERING SENSOR


U165705E01
3.475,0.271 3.821,0.413 0.347,0.142 10 E121 3.972,0.271 4.474,0.413 0.502,0.142 10 *B 5.529,0.274 5.876,0.416 0.347,0.142 10 E163 6.026,0.274 6.234,0.416 0.208,0.142 10 *C 0.05,0.055 0.397,0.197 0.347,0.142 10 *a 0.328,0.696 1.149,1.008 0.821,0.312 10 CANH 1.482,1.067 0.906,0.761 0.906,0.761 0.771,0.761 false 0.911,0.444 1.032,0.444 1.032,0.444 1.639,1.067 false 0.498,0.374 0.931,0.686 0.433,0.312 10 CANL 2.541,0.691 3.363,1.003 0.821,0.312 10 CANH 5.876,1.058 6.456,0.76 6.456,0.76 6.592,0.762 false 6.456,0.443 6.334,0.441 6.334,0.441 5.719,1.056 false 3.696,1.062 3.12,0.757 3.12,0.757 2.984,0.757 false 3.124,0.439 3.246,0.439 3.246,0.439 3.853,1.062 false 2.712,0.37 3.144,0.682 0.433,0.312 10 CANL 6.499,0.383 7.029,0.695 0.530,0.312 10 CANH 6.618,0.701 7.051,1.013 0.433,0.312 10 CANL 1.328,0.276 1.675,0.418 0.347,0.142 10 E181 1.825,0.276 2.327,0.418 0.502,0.142 10 *A

Text in Illustration
*A w/o Variable Gear Ratio Steering System, w/o Entry and Start System *B w/o Variable Gear Ratio Steering System, w/ Entry and Start System
*C w/ Variable Gear Ratio Steering System - -
*a Component without harness connected
(Steering Sensor)
- -

a.

Disconnect the steering sensor connector.

C344582E01
1.302,0.417 1.802,0.667 0.5,0.25 3.417,0.417 3.917,0.667 0.5,0.25 5.5,0.417 6,0.667 0.5,0.25 0.917,2 1.083,2 1.083,2 1.26,1.688 false 1.948,1.667 2.031,2 2.031,2 2.135,2 false 1.604,1.542 1.083,0.917 1.083,0.917 0.917,0.917 false 1.417,1.531 0.896,1.135 0.896,1.135 0.729,1.135 false 3.635,1.542 3.115,0.917 3.115,0.917 2.948,0.917 false 3.49,1.542 2.969,1.146 2.969,1.146 2.802,1.146 false 3.083,2 3.24,2 3.24,2 3.333,1.677 false 4,1.667 4.146,2 4.146,2 4.25,2 false 6.073,1.625 6.281,1.792 6.281,1.792 6.385,1.792 false 5.083,1.792 5.219,1.792 5.219,1.792 5.417,1.625 false 5.75,1.51 5.229,0.885 5.229,0.885 5.063,0.885 false 5.583,1.51 5.063,1.115 5.063,1.115 4.896,1.115 false 0.448,0.823 1.063,1.021 0.615,0.198 10 false CANH 0.292,1.052 0.906,1.25 0.615,0.198 10 false CANL 0.49,1.927 1.104,2.125 0.615,0.198 10 false ESS 2.167,1.927 2.667,2.167 0.5,0.24 10 false BAT 1.396,0.458 1.802,0.656 0.406,0.198 10 false E181 1.854,0.458 2.177,0.667 0.323,0.208 10 false *A 2.479,0.833 3.094,1.031 0.615,0.198 10 false CANH 4.615,0.802 5.229,1 0.615,0.198 10 false CANH 2.354,1.063 2.969,1.26 0.615,0.198 10 false CANL 4.448,1.042 5.063,1.24 0.615,0.198 10 false CANL 2.688,1.927 3.302,2.125 0.615,0.198 10 false ESS 4.302,1.917 4.802,2.156 0.5,0.24 10 false BAT 6.438,1.708 6.938,1.948 0.5,0.24 10 false BAT 4.698,1.708 5.313,1.906 0.615,0.198 10 false ESS 3.51,0.469 3.917,0.667 0.406,0.198 10 false E121 5.594,0.469 6,0.667 0.406,0.198 10 false E163 3.969,0.458 4.292,0.667 0.323,0.208 10 false *B 6.052,0.458 6.375,0.667 0.323,0.208 10 false *C

Text in Illustration
*A w/o Variable Gear Ratio Steering System, w/o Entry and Start System *B w/o Variable Gear Ratio Steering System, w/ Entry and Start System
*C w/ Variable Gear Ratio Steering System - -
*a Front view of wire harness connector
(to Steering Sensor)
- -


b.

Measure the resistance according to the value(s) in the table below.

w/o Variable Gear Ratio Steering System, w/o Entry and Start System
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E181-4 (CANH) - E181-3 (CANL) GR - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E181-4 (CANH) - E181-2 (ESS) GR - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E181-3 (CANL) - E181-2 (ESS) W - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E181-4 (CANH) - E181-6 (BAT) GR - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E181-3 (CANL) - E181-6 (BAT) W - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher

w/o Variable Gear Ratio Steering System, w/ Entry and Start System
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E121-3 (CANH) - E121-2 (CANL) GR - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E121-3 (CANH) - E121-1 (ESS) GR - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E121-2 (CANL) - E121-1 (ESS) W - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E121-3 (CANH) - E121-5 (BAT) GR - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E121-2 (CANL) - E121-5 (BAT) W - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher

w/ Variable Gear Ratio Steering System
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E163-3 (CANH) - E163-2 (CANL) GR - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E163-3 (CANH) - E163-1 (ESS) GR - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E163-2 (CANL) - E163-1 (ESS) W - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E163-3 (CANH) - E163-5 (BAT) GR - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E163-2 (CANL) - E163-5 (BAT) W - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK 4WD CONTROL ECU


U156424E01
1.788,1.497 1.422,2.249 1.422,2.249 1.263,2.249 false 1.788,1.281 1.422,0.596 1.422,0.596 1.263,0.596 false 2.635,0.3 2.916,0.446 0.281,0.145 10 A27 0.82,0.517 1.343,0.663 0.522,0.145 10 CANH 0.875,2.183 1.397,2.328 0.522,0.145 10 CANL 0.088,0.048 0.369,0.194 0.281,0.145 10 *a

Text in Illustration
*a Component without harness connected
(4WD Control ECU)
- -

a.
U156427E01
0.104,0.127 0.286,0.350 0.181,0.223 10 *a 1.558,0.249 1.823,0.388 0.265,0.140 10 A27 1.558,2.318 1.823,2.458 0.265,0.140 10 A28 2.921,1.224 2.726,0.588 2.726,0.588 2.568,0.588 false 2.313,3.579 2.571,3.865 2.571,3.865 2.728,3.865 false 2.903,1.465 2.717,1.883 2.717,1.883 2.54,1.883 false 0.514,1.465 0.7,1.883 0.7,1.883 0.878,1.883 false 0.896,1.806 1.365,1.945 0.468,0.140 10 +B 2.031,1.806 2.499,1.945 0.468,0.140 10 CANL 2.744,3.777 3.212,3.916 0.468,0.140 10 GND 2.062,0.499 2.531,0.639 0.468,0.140 10 CANH

Disconnect the 4WD control ECU connectors.

Text in Illustration
*a Front view of wire harness connector
(to 4WD Control ECU)


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
A27-20 (CANH) - A27-40 (CANL) P - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A27-20 (CANH) - A28-10 (GND) P - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
A27-40 (CANL) - A28-10 (GND) W - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
A27-20 (CANH) - A27-21 (+B) P - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A27-40 (CANL) - A27-21 (+B) W - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK TIRE PRESSURE WARNING ECU (w/ Tire Pressure Warning System)


U165207E01
1.442,2.058 1.62,2.058 1.62,2.058 1.813,1.368 false 0.101,0.059 0.278,0.213 0.177,0.154 10 *a 1.043,0.157 1.299,0.297 0.255,0.140 10 L65 1.516,0.157 1.771,0.297 0.255,0.140 10 *A 2.019,0.157 2.274,0.297 0.255,0.140 10 L75 2.491,0.157 2.747,0.297 0.255,0.140 10 *B 1.617,1.368 1.29,1.82 1.29,1.82 1.157,1.82 false 0.894,1.995 1.362,2.132 0.468,0.137 10 CANH 0.652,1.738 1.120,1.876 0.468,0.137 10 CANL

Text in Illustration
*A w/o Front Antenna
*B w/ Front Antenna
*a Component without harness connected
(Tire Pressure Warning ECU)

a.
U165419E01
1.429,2.061 1.606,2.061 1.606,2.061 1.793,1.542 false 0.052,0.047 0.228,0.201 0.177,0.154 10 *a 1.589,0.344 1.845,0.484 0.255,0.140 10 L65 1.648,1.542 1.324,1.806 1.324,1.806 1.191,1.806 false 0.679,1.714 1.147,1.852 0.468,0.137 10 CANH 0.931,1.969 1.399,2.107 0.468,0.137 10 CANL 1.348,1.458 1.083,1.351 1.083,1.351 0.95,1.351 false 0.683,1.259 1.152,1.396 0.468,0.137 10 +B 2.079,1.458 2.344,1.351 2.344,1.351 2.477,1.351 false 2.501,1.259 2.969,1.396 0.468,0.137 10 GND

w/o Front Antenna:

Text in Illustration
*a Front view of wire harness connector
(to Tire Pressure Warning ECU)

i.

Disconnect the tire pressure warning ECU connector.


ii.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
L65-9 (CANH) - L65-10 (CANL) R - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
L65-9 (CANH) - L65-12 (GND) R - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
L65-10 (CANL) - L65-12 (GND) W - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
L65-9 (CANH) - L65-7 (+B) R - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher
L65-10 (CANL) - L65-7 (+B) W - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher



b.
U165411E02
1.458,1.948 1.635,1.948 1.635,1.948 1.823,1.427 false 1.677,1.427 1.354,1.698 1.354,1.698 1.219,1.698 false 2.198,2.906 2.406,3.146 2.406,3.146 2.531,3.146 false 2.104,1.344 2.375,1.24 2.375,1.24 2.5,1.24 false 0.083,0.094 0.479,0.323 0.396,0.229 10 false *a 0.083,1.938 0.5,2.135 0.417,0.198 10 false *b 0.438,2.594 0.823,2.781 0.385,0.188 10 false E22 1.583,0.292 2.042,0.5 0.458,0.208 10 false L75 0.698,1.604 1.313,1.802 0.615,0.198 10 false CANH 0.958,1.875 1.521,2.073 0.563,0.198 10 false CANL 2.594,3.052 3.104,3.26 0.51,0.208 10 false BAT 2.531,1.146 3.115,1.354 0.583,0.208 10 false GND

w/ Front Antenna:

Text in Illustration
*a Front view of wire harness connector
(to Tire Pressure Warning ECU)
*b Front view DLC3

i.

Disconnect the tire pressure warning ECU connector.


ii.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
L75-9 (CANH) - L75-10 (CANL) R - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
L75-9 (CANH) - L75-12 (GND) R - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
L75-10 (CANL) - L75-12 (GND) W - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
L75-9 (CANH) - E22-16 (BAT) R - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher
L75-10 (CANL) - E22-16 (BAT) W - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher




CHECK STEERING CONTROL ECU (w/ Variable Gear Ratio Steering System)


U165253E01
0.148,0.143 0.353,0.314 0.205,0.171 10 *a 4.859,0.381 5.202,0.521 0.343,0.140 10 E161 5.772,0.446 6.270,0.587 0.498,0.140 10 CNH1 5.252,1.374 5.65,0.52 5.65,0.52 5.744,0.52 false 5.225,1.573 5.573,2.267 5.573,2.267 5.723,2.267 false 5.744,2.188 6.242,2.328 0.498,0.140 10 CNL1

Text in Illustration
*a Component without harness connected
(Steering Control ECU)
- -

a.
U165186E01
1.457,0.987 1.177,1.31 1.177,1.31 0.979,1.31 false 0.458,1.226 0.890,1.362 0.432,0.137 10 PGND 0.327,1.855 0.734,1.992 0.408,0.137 10 CNH1 0.059,0.049 0.421,0.186 0.362,0.137 10 *a 2.377,1.662 2.728,1.799 0.351,0.137 10 E161 1.351,2.445 1.023,1.931 1.023,1.931 0.825,1.931 false 1.101,2.712 0.884,2.968 0.884,2.968 0.686,2.968 false 1.101,2.712 0.884,2.968 0.884,2.968 0.686,2.968 false 0.371,2.896 0.779,3.033 0.408,0.137 10 +BI 0.521,3.174 0.928,3.311 0.408,0.137 10 CNL1 1.351,2.712 1.203,3.266 1.203,3.266 1.005,3.266 false 0.487,0.648 0.838,0.785 0.351,0.137 10 E159

Disconnect the steering control ECU connectors.

Text in Illustration
*a Front view of wire harness connector
(to Steering Control ECU)


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E161-3 (CNH1) - E161-9 (CNL1) P - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E161-3 (CNH1) - E159-1 (PGND) P - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E161-9 (CNL1) - E159-1 (PGND) W - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E161-3 (CNH1) - E161-7 (+BI) P - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E161-9 (CNL1) - E161-7 (+BI) W - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK POWER STEERING ECU ASSEMBLY (w/ Variable Flow Control Solenoid Valve)


U164976E01
1.406,0.395 1.753,0.537 0.347,0.142 10 E102 0.118,0.112 0.465,0.254 0.347,0.142 10 *a 2.82,0.947 3.238,1.089 0.419,0.142 10 CANH 2.678,0.568 3.097,0.710 0.419,0.142 10 CANL 2.645,0.651 2.491,0.651 2.491,0.651 2.048,1.355 false 2.223,1.332 2.678,1.025 2.678,1.025 2.796,1.025 false

Text in Illustration
*a Component without harness connected
(Power Steering ECU Assembly)

a.
U164991E02
2.208,2.948 2.417,3.115 2.417,3.115 2.5,3.115 false 2.063,1.146 2.375,0.698 2.375,0.698 2.458,0.698 false 2.188,1.146 2.521,0.979 2.521,0.979 2.615,0.979 false 1.948,1.24 2.292,1.594 2.292,1.594 2.458,1.594 false 0.615,0.99 1.094,1.177 0.479,0.188 10 false E102 0.469,2.688 0.865,2.885 0.396,0.198 10 false E22 0.063,0.052 0.385,0.271 0.323,0.219 10 false *a 0.063,2 0.375,2.198 0.313,0.198 10 false *b 2.552,3.01 3.083,3.219 0.531,0.208 10 false BAT 2.635,0.896 3.219,1.104 0.583,0.208 10 false CANH 2.5,1.5 2.979,1.688 0.479,0.188 10 false GND 2.49,0.594 3.063,0.792 0.573,0.198 10 false CANL

Disconnect the power steering ECU assembly connector.

Text in Illustration
*a Front view of wire harness connector
(to Power Steering ECU Assembly)
*b Front view of DLC3


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E102-1 (CANH) - E102-2 (CANL) LG - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E102-1 (CANH) - E102-3 (GND) LG - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E102-2 (CANL) - E102-3 (GND) W - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E102-1 (CANH) - E22-16 (BAT) LG - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E102-2 (CANL) - E22-16 (BAT) W - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Entry and Start System)


U164301E01
4.479,0.432 4.624,0.432 4.624,0.432 4.818,1.144 false 0.085,0.087 0.262,0.241 0.177,0.154 10 *a 5.086,0.366 5.431,0.506 0.346,0.140 10 E130 4.714,1.144 4.187,0.683 4.187,0.683 4.079,0.683 false 4.071,0.352 4.539,0.490 0.468,0.137 10 CANH 3.678,0.616 4.146,0.754 0.468,0.137 10 CANL

Text in Illustration
*a Component without harness connected
(Certification ECU [Smart Key ECU Assembly])
- -

a.
U165487E01
0.106,0.056 0.290,0.253 0.184,0.198 10 *a 1.502,0.305 1.860,0.454 0.357,0.149 10 E130 2.93,0.537 3.341,0.686 0.411,0.149 10 CANL 3.163,1.276 3.365,1.425 0.202,0.149 10 +B 2.773,0.308 3.220,0.457 0.448,0.149 10 CANH 2.531,1.039 2.761,0.623 2.761,0.623 2.91,0.623 false 2.75,0.391 2.535,0.391 2.535,0.391 2.379,1.045 false 0.759,1.314 0.581,1.552 0.581,1.552 0.452,1.552 false 2.824,1.121 3.002,1.359 3.002,1.359 3.131,1.359 false 0.289,1.488 0.492,1.637 0.202,0.149 10 E

Disconnect the certification ECU (smart key ECU assembly) connector.

Text in Illustration
*a Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly])


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E130-7 (CANH) - E130-8 (CANL) B - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E130-7 (CANH) - E130-11 (E) B - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
E130-8 (CANL) - E130-11 (E) W - BR Cable disconnected from negative (-) battery terminal 200 Ω or higher
E130-7 (CANH) - E130-10 (+B) B - P Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E130-8 (CANL) - E130-10 (+B) W - P Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK HEADLIGHT LEVELING ECU ASSEMBLY (w/ Automatic High Beam System)


U166545E01
3.337,0.144 3.684,0.286 0.347,0.142 10 E101 0.099,0.064 0.446,0.206 0.347,0.142 10 *a 1.448,0.205 1.891,0.347 0.443,0.142 10 CANL 1.864,0.269 1.991,0.269 1.991,0.269 2.479,0.683 false 1.864,0.269 1.991,0.269 1.991,0.269 2.479,0.683 false 1.765,0.041 2.208,0.183 0.443,0.142 10 CANH 2.216,0.105 2.342,0.105 2.342,0.105 2.602,0.679 false

Text in Illustration
*a Component without harness connected
(Headlight Leveling ECU Assembly)
- -

a.
U165703E01
0.853,0.178 1.200,0.320 0.347,0.142 10 E101 0.07,0.064 0.417,0.206 0.347,0.142 10 *a 0.07,1.751 0.417,1.893 0.347,0.142 10 *b 1.732,0.081 2.505,0.223 0.773,0.142 10 CANL 1.615,0.319 2.436,0.631 0.821,0.312 10 CANH 2.258,0.16 2.412,0.16 2.412,0.16 2.82,0.899 false 2.679,0.876 2.276,0.399 2.276,0.399 2.159,0.399 false 1.594,1.816 1.860,1.958 0.266,0.142 10 E22 2.591,2.945 2.910,3.087 0.319,0.142 10 BAT 2.271,2.831 2.447,3.027 2.447,3.027 2.565,3.027 false 2.133,1.481 2.452,1.623 0.319,0.142 10 E1 1.626,1.141 1.989,1.564 1.989,1.564 2.106,1.564 false

Disconnect the headlight leveling ECU assembly connector.

Text in Illustration
*a Front view of wire harness connector
(to Headlight Leveling ECU Assembly)
*b Front view of DLC3


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E101-12 (CANH) - E101-13 (CANL) LG - B Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E101-12 (CANH) - E101-22 (E1) LG - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E101-13 (CANL) - E101-22 (E1) B - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E101-12 (CANH) - E22-16 (BAT) LG - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E101-13 (CANL) - E22-16 (BAT) B - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK HEADLIGHT LEVELING ECU ASSEMBLY (w/o Automatic High Beam System)


U165450E01
3.185,0.945 2.718,0.598 2.718,0.598 2.583,0.598 false 2.793,0.411 2.966,0.411 2.966,0.411 3.272,0.926 false 3.441,0.299 3.786,0.441 0.346,0.142 10 E109 2.166,0.528 2.595,0.670 0.429,0.142 10 CANL 2.357,0.336 2.786,0.478 0.429,0.142 10 CANH 0.126,0.084 0.472,0.226 0.346,0.142 10 *a

Text in Illustration
*a Component without harness connected
(Headlight Leveling ECU Assembly)
- -

a.
U165451E01
2.935,0.487 3.323,0.629 0.389,0.142 10 CANL 2.733,0.143 3.180,0.285 0.448,0.142 10 CANH 2.385,0.951 2.784,0.564 2.784,0.564 2.888,0.564 false 2.698,0.233 2.514,0.233 2.514,0.233 2.247,0.951 false 2.617,3.001 3.064,3.143 0.448,0.142 10 BAT 2.217,2.829 2.428,3.078 2.428,3.078 2.57,3.078 false 0.073,0.096 0.267,0.238 0.194,0.142 10 *a 1.361,0.232 1.704,0.374 0.343,0.142 10 E109 0.077,1.802 0.271,1.944 0.194,0.142 10 *b 0.318,2.514 0.588,2.656 0.270,0.142 10 E22 3.055,1.192 3.291,1.334 0.236,0.142 10 E1 2.64,1.05 2.866,1.269 2.866,1.269 3.008,1.269 false

Disconnect the headlight leveling ECU assembly connector.

Text in Illustration
*a Front view of wire harness connector
(to Headlight Leveling ECU Assembly)
*b Front view of DLC3


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E109-6 (CANH) - E109-7 (CANL) LG - B Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E109-6 (CANH) - E109-9 (E1) LG - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E109-7 (CANL) - E109-9 (E1) B - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E109-6 (CANH) - E22-16 (BAT) LG - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E109-7 (CANL) - E22-16 (BAT) B - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK OUTER MIRROR CONTROL ECU ASSEMBLY LH (w/ Memory)


U165546E01
4.756,1.509 4.611,1.509 4.611,1.509 4.459,1.086 false 0.056,0.043 0.233,0.196 0.177,0.154 10 *a 4.115,0.25 4.336,0.390 0.221,0.140 10 I41 4.577,1.086 4.841,1.301 4.841,1.301 4.95,1.301 false 4.967,1.227 5.435,1.364 0.468,0.137 10 CANN 4.787,1.447 5.255,1.585 0.468,0.137 10 CANP

Text in Illustration
*a Component without harness connected
(Outer Mirror Control ECU Assembly LH)
- -

a.
U165531E01
1.304,1.259 1.073,1.463 1.073,1.463 0.888,1.463 false 1.155,1.814 1.387,1.814 1.387,1.814 1.436,1.259 false 0.655,1.708 1.151,1.871 0.496,0.163 10 CANP 0.367,1.373 0.863,1.535 0.496,0.163 10 CANN 0.106,0.075 0.602,0.238 0.496,0.163 10 *a 0.54,0.723 0.753,0.870 0.213,0.147 10 I41 2.196,0.917 2.471,0.576 2.471,0.576 2.608,0.576 false 2.024,0.951 2.236,0.307 2.236,0.307 2.382,0.307 false 2.63,0.499 3.126,0.662 0.496,0.163 10 GND 2.424,0.23 2.920,0.392 0.496,0.163 10 CPUB

Disconnect the outer mirror control ECU assembly LH connector.

Text in Illustration
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly LH)


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
I41-9 (CANP) - I41-8 (CANN) BE - L Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I41-9 (CANP) - I41-7 (GND) BE - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
I41-8 (CANN) - I41-7 (GND) L - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
I41-9 (CANP) - I41-6 (CPUB) BE - G Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I41-8 (CANN) - I41-6 (CPUB) L - G Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK OUTER MIRROR CONTROL ECU ASSEMBLY RH (w/ Memory)


U165547E01
4.756,1.509 4.611,1.509 4.611,1.509 4.459,1.086 false 0.056,0.043 0.233,0.196 0.177,0.154 10 *a 4.115,0.25 4.336,0.390 0.221,0.140 10 I38 4.577,1.086 4.841,1.301 4.841,1.301 4.95,1.301 false 4.967,1.227 5.435,1.364 0.468,0.137 10 CANN 4.787,1.447 5.255,1.585 0.468,0.137 10 CANP

Text in Illustration
*a Component without harness connected
(Outer Mirror Control ECU Assembly RH)
- -

a.
U165532E01
1.304,1.259 1.073,1.463 1.073,1.463 0.888,1.463 false 1.155,1.814 1.387,1.814 1.387,1.814 1.436,1.259 false 0.655,1.708 1.151,1.871 0.496,0.163 10 CANP 0.367,1.373 0.863,1.535 0.496,0.163 10 CANN 0.106,0.075 0.602,0.238 0.496,0.163 10 *a 0.54,0.723 0.753,0.870 0.213,0.147 10 I38 2.196,0.917 2.471,0.576 2.471,0.576 2.608,0.576 false 2.024,0.951 2.236,0.307 2.236,0.307 2.382,0.307 false 2.63,0.499 3.126,0.662 0.496,0.163 10 GND 2.424,0.23 2.920,0.392 0.496,0.163 10 CPUB

Disconnect the outer mirror control ECU assembly RH connector.

Text in Illustration
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly RH)


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
I38-9 (CANP) - I38-8 (CANN) LG - L Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I38-9 (CANP) - I38-7 (GND) LG - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
I38-8 (CANN) - I38-7 (GND) L - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
I38-9 (CANP) - I38-6 (CPUB) LG - G Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I38-8 (CANN) - I38-6 (CPUB) L - G Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK MULTIPLEX TILT AND TELESCOPIC ECU (w/ Power Tilt and Power Telescopic Steering Column System)


U165226E01
4.099,0.787 4.43,0.43 4.43,0.43 4.587,0.43 false 3.648,1.417 3.844,1.417 3.844,1.417 4.066,1.019 false 3.479,0.297 3.821,0.434 0.342,0.137 10 E144 0.108,0.037 0.382,0.174 0.274,0.137 10 *a 4.605,0.364 5.118,0.502 0.514,0.137 10 CANP 3.22,1.36 3.664,1.497 0.444,0.137 10 CANN

Text in Illustration
*a Component without harness connected
(Multiplex Tilt and Telescopic ECU)
- -

a.
U165224E01
2.117,1.085 2.391,1.669 2.391,1.669 2.539,1.669 false 2.491,0.958 2.715,0.706 2.715,0.706 2.864,0.706 false 2.342,0.949 2.599,1.355 2.599,1.355 2.748,1.355 false 2.082,0.913 2.384,0.395 2.384,0.395 2.548,0.395 false 0.069,0.062 0.343,0.263 0.274,0.201 10 *a 0.788,0.216 1.144,0.355 0.356,0.139 10 E144 2.602,0.319 3.022,0.458 0.420,0.139 10 CANP 2.582,1.591 3.002,1.729 0.420,0.139 10 CANN 2.881,0.633 3.301,0.772 0.420,0.139 10 GND 2.774,1.278 3.193,1.416 0.420,0.139 10 +B

Disconnect the multiplex tilt and telescopic ECU connector.

Text in Illustration
*a Rear view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E144-3 (CANP) - E144-11 (CANN) P - L Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E144-3 (CANP) - E144-1 (GND) P - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E144-11 (CANN) - E144-1 (GND) L - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E144-3 (CANP) - E144-2 (+B) P - LA-W Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E144-11 (CANN) - E144-2 (+B) L - LA-W Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK POWER SEAT SWITCH ASSEMBLY (w/ Memory)


U164970E02
2.125,1.438 2.24,1.438 2.24,1.438 3.021,0.979 false 3.594,1.417 3.458,1.417 3.458,1.417 3.135,0.979 false 1.927,0.823 2.26,1.031 0.333,0.208 10 false c47 1.677,1.354 2.167,1.542 0.49,0.188 10 false MPX1 3.646,1.344 4.271,1.521 0.625,0.177 10 false MPX2 0.073,0.021 0.479,0.198 0.406,0.177 10 false *a

Text in Illustration
*a Component without harness connected
(Power Seat Switch Assembly)
- -

a.
U165535E01
0.12,0.073 0.316,0.269 0.196,0.196 10 *a 1.621,1.697 2.036,1.841 0.415,0.144 10 MPX2 1.478,1.888 1.892,2.032 0.415,0.144 10 MPX1 0.291,1.106 0.540,1.250 0.250,0.144 10 c47 2.757,0.631 3.007,0.774 0.250,0.144 10 c46 2.864,1.516 3.279,1.660 0.415,0.144 10 +B2 2.812,0.96 3.226,1.104 0.415,0.144 10 GND 1.394,1.6 1.498,1.791 1.498,1.791 1.609,1.791 false 1.471,1.972 1.385,1.972 1.385,1.972 1.286,1.6 false 2.841,1.593 2.755,1.593 2.755,1.593 2.57,1.434 false 2.571,1.216 2.688,1.054 2.688,1.054 2.799,1.054 false

Disconnect the power seat switch assembly connectors.

Text in Illustration
*a Rear view of wire harness connector
(to Power Seat Switch Assembly)


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
c47-8 (MPX1) - c47-7 (MPX2) V - L Cable disconnected from negative (-) battery terminal 54 to 69 Ω
c47-8 (MPX1) - c46-1 (GND) V - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
c47-7 (MPX2) - c46-1 (GND) L - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
c47-8 (MPX1) - c46-6 (+B2) V - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher
c47-7 (MPX2) - c46-6 (+B2) L - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK POWER BACK DOOR UNIT ASSEMBLY (POWER BACK DOOR ECU) (w/ Power Back Door System)


U163850E01
3.94,0.27 4.190,0.413 0.249,0.143 10 L52 0.053,0.048 0.302,0.191 0.249,0.143 10 *a 2.623,0.39 3.037,0.533 0.414,0.143 10 MPX1 2.722,0.2 3.136,0.343 0.414,0.143 10 MPX2 3.676,0.939 3.119,0.452 3.119,0.452 3.051,0.452 false 3.147,0.282 3.372,0.282 3.372,0.282 3.797,0.939 false

Text in Illustration
*a Component without harness connected
(Power Back Door Unit Assembly [Power Back Door ECU])
- -

a.
U165539E01
1.665,0.277 1.915,0.418 0.250,0.141 10 L52 0.063,0.055 0.336,0.196 0.273,0.141 10 *a 0.59,1.614 1.011,1.755 0.421,0.141 10 MPX2 1.668,1.255 1.229,1.694 1.229,1.694 1.104,1.694 false 0.935,1.937 1.356,2.078 0.421,0.141 10 MPX1 1.786,1.273 1.575,2.017 1.575,2.017 1.45,2.017 false 2.413,1.061 2.708,0.766 2.708,0.766 2.88,0.766 false 2.665,0.411 2.528,0.411 2.528,0.411 2.228,1.051 false 2.902,0.7 3.323,0.841 0.421,0.141 10 GND 2.69,0.328 3.111,0.469 0.421,0.141 10 ECUB

Disconnect the power back door unit assembly (power back door ECU) connector.

Text in Illustration
*a Front view of wire harness connector
(to Power Back Door Unit Assembly [Power Back Door ECU])


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
L52-6 (MPX1) - L52-5 (MPX2) V - L Cable disconnected from negative (-) battery terminal 54 to 69 Ω
L52-6 (MPX1) - L52-11 (GND) V - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
L52-5 (MPX2) - L52-11 (GND) L - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
L52-6 (MPX1) - L52-10 (ECUB) V - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher
L52-5 (MPX2) - L52-10 (ECUB) L - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK NO. 2 MAIN BODY ECU (w/ Tail Gate Closer System)


U164150E01
3.104,0.372 3.362,0.533 0.258,0.161 10 L50 0.137,0.085 0.395,0.246 0.258,0.161 10 *a 1.465,0.33 1.921,0.491 0.456,0.161 10 MPX+ 2.453,1.312 1.83,0.689 1.83,0.689 1.62,0.689 false 1.914,0.419 2.184,0.419 2.184,0.419 2.612,1.307 false 1.206,0.607 1.661,0.767 0.456,0.161 10 MPX-

Text in Illustration
*a Component without harness connected
(No. 2 Main Body ECU)
- -

a.
U165540E01
1.665,0.277 1.915,0.418 0.250,0.141 10 L50 0.063,0.055 0.336,0.196 0.273,0.141 10 *a 0.347,1.589 0.768,1.730 0.421,0.141 10 BECU 1.17,1.404 0.985,1.67 0.985,1.67 0.861,1.67 false 0.583,0.495 1.004,0.636 0.421,0.141 10 GND 1.861,1.204 1.122,0.576 1.122,0.576 0.997,0.576 false 2.602,1.061 2.772,0.754 2.772,0.754 2.943,0.754 false 2.738,0.514 2.601,0.514 2.601,0.514 2.417,1.051 false 2.966,0.671 3.347,0.812 0.381,0.141 10 MPX- 2.763,0.431 3.184,0.572 0.421,0.141 10 MPX+

Disconnect the No. 2 main body ECU connector.

Text in Illustration
*a Front view of wire harness connector
(to No. 2 Main Body ECU)


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
L50-11 (MPX+) - L50-12 (MPX-) LG - L Cable disconnected from negative (-) battery terminal 54 to 69 Ω
L50-11 (MPX+) - L50-7 (GND) LG - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
L50-12 (MPX-) - L50-7 (GND) L - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
L50-11 (MPX+) - L50-14 (BECU) LG - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher
L50-12 (MPX-) - L50-14 (BECU) L - R Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK BUS BUFFER ECU (w/ Bus Buffer ECU)


a.
U165667E02
2.042,0.969 2.375,0.76 2.375,0.76 2.531,0.76 false 2.417,0.313 2.26,0.313 2.26,0.313 1.875,0.969 false 2.198,2.948 2.521,3.156 2.521,3.156 2.688,3.156 false 1.656,2.51 1.333,2.198 1.333,2.198 1.167,2.198 false 0.125,0.083 0.563,0.385 0.438,0.302 10 false *a 0.479,0.865 0.948,1.083 0.469,0.219 10 false E173 0.125,1.813 0.563,2.115 0.438,0.302 10 false *b 0.854,2.115 1.375,2.271 0.521,0.156 10 false CG 2.729,3.063 3.167,3.229 0.438,0.167 10 false BAT 2.583,0.688 3.156,0.896 0.573,0.208 10 false CAN- 2.469,0.229 3.073,0.479 0.604,0.25 10 false CAN+ 0.406,2.656 0.781,2.844 0.375,0.188 10 false E22

Disconnect the bus buffer ECU connector.

Text in Illustration
*a Front view of wire harness connector
(to Bus Buffer ECU)
*b Front view of DLC3


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
E173-2 (CAN+) - E173-1 (CAN-) BE - W Cable disconnected from negative (-) battery terminal 54 to 69 Ω
E173-2 (CAN+) - E22-4 (CG) BE - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E173-1 (CAN-) - E22-4 (CG) W - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
E173-2 (CAN+) - E22-16 (BAT) BE - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E173-1 (CAN-) - E22-16 (BAT) W - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK OPTION CONNECTOR (w/ Option Connector)


a.
U165704E02
2.042,1.146 2.323,0.99 2.323,0.99 2.479,0.99 false 2.448,0.646 2.292,0.646 2.292,0.646 1.865,1.146 false 2.229,2.677 2.552,2.875 2.552,2.875 2.708,2.875 false 1.646,2.24 1.323,1.927 1.323,1.927 1.156,1.927 false 0.115,0.073 0.552,0.375 0.438,0.302 10 false *a 0.469,0.948 0.948,1.188 0.479,0.24 10 false F129 0.115,1.552 0.552,1.854 0.438,0.302 10 false *b 0.854,1.854 1.292,2.156 0.438,0.302 10 false CG 2.74,2.792 3.229,2.99 0.49,0.198 10 false BAT 2.51,0.906 3.063,1.115 0.552,0.208 10 false CANL 2.49,0.563 3.104,0.75 0.615,0.188 10 false CANH 0.396,2.406 0.76,2.615 0.365,0.208 10 false E22

Disconnect the option connector.

Text in Illustration
*a Front view of wire harness connector
(to Option Connector)
*b Front view of DLC3


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F129-4 (CANH) - F129-5 (CANL) G - GR Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F129-4 (CANH) - E22-4 (CG) G - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
F129-5 (CANL) - E22-4 (CG) GR - W-B Cable disconnected from negative (-) battery terminal 200 Ω or higher
F129-4 (CANH) - E22-16 (BAT) G - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F129-5 (CANL) - E22-16 (BAT) GR - L Cable disconnected from negative (-) battery terminal 6 kΩ or higher