Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Start Function) › from 2017.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255570 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2286  Runnable Signal Malfunction  P0335  Crankshaft Position Sensor Circuit Malfunction (NE Signal)  


DESCRIPTION

These DTCs are stored when the engine speed signal sent by the ECM via direct line and the engine speed signal sent via CAN communication do not match.

HINT:

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2286 The engine speed signal sent by the ECM via direct line and the engine speed signal sent via CAN communication (1-trip detection logic*) do not match.
·

AM2 fuse

·

SFI system

·

ECD system

·

Certification ECU (smart key ECU assembly)

·

Harness or connector


Disconnect the cable from the negative (-) battery terminal, wait 30 seconds and reconnect the cable to the negative (-) battery terminal. Wait 20 seconds or more with the engine switch off, then start the engine and maintain an engine speed of 1000 rpm or more for 20 seconds or more.
P0335 The engine speed signal sent by the ECM via direct line and the engine speed signal sent via CAN communication (1-trip detection logic*) do not match.
·

AM2 fuse

·

SFI system

·

ECD system

·

Certification ECU (smart key ECU assembly)

·

Harness or connector


Allow the engine to idle for 10 seconds or more.

*: Only detected while a malfunction is present and the engine switch is on (IG)


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
·

When the signal sent via either the direct line or CAN communication is malfunctioning and indicates no vehicle speed, there is no effect on vehicle behavior. (A malfunction is detected after the engine switch is turned on (IG).)

·

When the signal sent via either direct line or CAN communication is malfunctioning and indicates that the vehicle is moving, the engine cannot be started. However, the engine can be started after the engine switch has been turned off.


·

When the signal sent via either direct line or CAN communication is malfunctioning and indicates no vehicle speed, there is no effect on vehicle behavior.

·

When the signal sent via either direct line or CAN communication is malfunctioning and indicates that the vehicle is moving:

If the following conditions are met, it is determined that the malfunction is not in CAN communication but in the direct line (NE).

*

When the engine switch is pressed, the system controls the engine based on the starter OFF permission flag (perfect injection signal judgment) via CAN communication, causing the engine to stop cranking.

*

When the engine switch is pressed and held, the system controls the engine based on the engine speed signal via CAN communication, causing the engine to stop cranking.


If the following conditions are met, it is determined that the malfunction is not in the direct line (NE) but in CAN communication.

*

When the engine switch is pressed, the system controls the engine based on the engine speed signal via direct line, causing the engine to stop cranking.

*

When the engine switch is pressed and held, the system controls the engine based on the engine speed signal via direct line, causing the engine to stop cranking.


If the following conditions are met, it is determined that there is a malfunction in both CAN communication and the direct line (NE).

*

When the engine switch is pressed, the engine stops cranking after 6 seconds.

*

When the engine switch is pressed and held, the engine remains cranking for up to 30 seconds.





Related Data List and Active Test Items
DTC Data List Item Active Test Item
B2286
P0335
Power Source Control
·

Engine Condition


Starting Control
·

Engine Speed


-

WIRING DIAGRAM

C388144E01
0.115,0.042 1,0.292 0.885,0.25 12 false for RHD: 0.583,3.354 2.5,3.552 1.917,0.198 10 false : CAN Communication Line 4.833,2.719 6.656,3.083 1.823,0.365 10 false Certification ECU (Smart Key ECU Assembly) 1.333,2.667 1.708,2.865 0.375,0.198 10 false ECM 1.573,1.281 1.948,1.479 0.375,0.198 10 false NEO 2.01,1.396 2.385,1.594 0.375,0.198 10 false A52 2.396,1.396 2.771,1.594 0.375,0.198 10 false A52 1.917,0.583 3,0.781 1.083,0.198 10 false from Battery 2.667,3.021 4.583,3.219 1.917,0.198 10 false *1: for 1UR-FE 2.667,3.365 4.583,3.563 1.917,0.198 10 false *2: for 1VD-FTV 4.844,1.396 5.219,1.594 0.375,0.198 10 false E128 4.833,0.604 5.208,0.802 0.375,0.198 10 false E130 6.146,1.854 6.521,2.052 0.375,0.198 10 false E130 3.708,0.75 4.083,0.948 0.375,0.198 10 false AM2 5.75,1 6.063,1.198 0.313,0.198 10 false +B 5.25,0.583 5.563,0.781 0.313,0.198 10 false +B 5.25,1.281 5.563,1.479 0.313,0.198 10 false NE 5.917,1.854 6.073,2.052 0.156,0.198 10 false E 6.219,1.646 6.531,1.844 0.313,0.198 10 false 11 4.917,0.396 5.229,0.594 0.313,0.198 10 false 10 4.917,1.188 5.229,1.385 0.313,0.198 10 false 14 2.427,1.188 2.74,1.385 0.313,0.198 10 false 51 2.083,1.188 2.24,1.385 0.156,0.198 10 false 7 2.052,1.615 2.365,1.813 0.313,0.198 10 false *1 2.458,1.615 2.771,1.813 0.313,0.198 10 false *2

C348659E04
0.542,3.385 2.271,3.583 1.729,0.198 10 false : CAN Communication Line 2.031,1.406 2.427,1.594 0.396,0.188 10 false A38 2.375,1.417 2.698,1.604 0.323,0.188 10 false A38 2.75,1.406 3.146,1.594 0.396,0.188 10 false C45 3.125,1.417 3.521,1.604 0.396,0.188 10 false A38 2.063,1.219 2.458,1.406 0.396,0.188 10 false 41 2.49,1.208 2.75,1.385 0.26,0.177 10 false 7 2.781,1.208 3.052,1.365 0.271,0.156 10 false 31 3.177,1.219 3.448,1.375 0.271,0.156 10 false 51 5.229,1.302 5.625,1.49 0.396,0.188 10 false NE 1.594,1.302 1.99,1.49 0.396,0.188 10 false NEO 5.26,0.615 5.656,0.802 0.396,0.188 10 false +B 3.719,0.781 4.292,1 0.573,0.219 10 false AM2 4.844,0.615 5.24,0.802 0.396,0.188 10 false E130 4.938,0.406 5.135,0.594 0.198,0.188 10 false 10 2,0.615 2.813,0.844 0.813,0.229 10 false from Battery 4.896,1.208 5.094,1.396 0.198,0.188 10 false 14 5.969,1.865 6.146,2.031 0.177,0.167 10 false E 6.177,1.875 6.573,2.063 0.396,0.188 10 false E130 6.219,1.677 6.417,1.885 0.198,0.208 10 false 11 1.313,2.677 1.667,2.865 0.354,0.188 10 false ECM 5.021,2.677 6.542,3.063 1.521,0.385 10 false Certification ECU (Smart Key ECU Assembly) 2.063,1.625 2.26,1.844 0.198,0.219 10 false *1 2.417,1.615 2.615,1.833 0.198,0.219 10 false *2 2.802,1.615 3,1.833 0.198,0.219 10 false *3 3.188,1.615 3.385,1.833 0.198,0.219 10 false *5 2.25,2.479 3.188,2.688 0.938,0.208 10 false *1: for 3UR-FE 3.354,2.49 4.292,2.698 0.938,0.208 10 false *2: for 1UR-FE 2.271,2.823 4.906,3.021 2.635,0.198 10 false *3: for 1GR-FE with Manual Transmission 2.281,3.427 3.333,3.635 1.052,0.208 10 false *5: for 1VD-FTV 0.073,0.063 1.063,0.396 0.99,0.333 12 false for LHD: 4.833,1.396 5.229,1.583 0.396,0.188 10 false E128 5.688,0.917 6.083,1.104 0.396,0.188 10 false +B 2.073,1.792 2.271,2.01 0.198,0.219 10 false *4 2.271,3.125 5.135,3.333 2.865,0.208 10 false *4: for 1GR-FE with Automatic Transmission

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus:

Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Before replacing the certification ECU (smart key ECU assembly) or ECM, refer to the entry and start system (for Start Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>PRECAUTION).

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.READ VALUE USING GTS (ENGINE CONDITION / ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control or Starting Control / Data List.


e.

According to the display on the GTS, read the Data List.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Engine Condition Engine state/Stop or Run Stop: Engine stopped
Run: Engine running
-

Starting Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Engine Speed Engine speed/0 to 16383 r/min Fluctuates in accordance with engine speed -

OK:

The Data List item changes in accordance with the engine condition.


Result
Result Proceed to
OK A
NG for SFI system B
for ECD system C

HINT:

·

For the ECD SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING), refer to the following:






A

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

B

GO TO SFI SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

C

GO TO ECD SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

3.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

3.CHECK HARNESS AND CONNECTOR (GROUND)

OK

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)
a.

Disconnect the E128 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A38*1, A52*2 or C45*3 ECM connector.

*1: for 3UR-FE, 1UR-FE (for LHD) or 1VD-FTV (for LHD) or 1GR-FE with Automatic Transmission

*2: for 1UR-FE (for RHD) or 1VD-FTV (for RHD)

*3: for 1GR-FE with Manual Transmission



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 3UR-FE:
Tester Connection Condition Specified Condition
E128-14 (NE) - A38-41 (NEO) Always Below 1 Ω
E128-14 (NE) or A38-41 (NEO) - Body ground 10 kΩ or higher

for 1UR-FE (for RHD):
Tester Connection Condition Specified Condition
E128-14 (NE) - A52-7 (NEO) Always Below 1 Ω
E128-14 (NE) or A52-7 (NEO) - Body ground 10 kΩ or higher

for 1UR-FE (for LHD):
Tester Connection Condition Specified Condition
E128-14 (NE) - A38-7 (NEO) Always Below 1 Ω
E128-14 (NE) or A38-7 (NEO) - Body ground 10 kΩ or higher

for 1GR-FE with Manual Transmission:
Tester Connection Condition Specified Condition
E128-14 (NE) - C45-31 (NEO) Always Below 1 Ω
E128-14 (NE) or C45-31 (NEO) - Body ground 10 kΩ or higher

for 1GR-FE with Automatic Transmission:
Tester Connection Condition Specified Condition
E128-14 (NE) - A38-41 (NEO) Always Below 1 Ω
E128-14 (NE) or A38-41 (NEO) - Body ground 10 kΩ or higher

for 1VD-FTV (for RHD):
Tester Connection Condition Specified Condition
E128-14 (NE) - A52-51 (NEO) Always Below 1 Ω
E128-14 (NE) or A52-51 (NEO) - Body ground 10 kΩ or higher

for 1VD-FTV (for LHD):
Tester Connection Condition Specified Condition
E128-14 (NE) - A38-51 (NEO) Always Below 1 Ω
E128-14 (NE) or A38-51 (NEO) - Body ground 10 kΩ or higher




OK

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the E128 and E130 certification ECU (smart key ECU assembly) connectors.


b.

Reconnect the A38*1, A52*2 or C45*3 ECM connector.

*1: for 3UR-FE, 1UR-FE (for LHD) , 1VD-FTV (for LHD) or 1GR-FE with Automatic Transmission

*2: for 1UR-FE (for RHD) or 1VD-FTV (for RHD)

*3: for 1GR-FE with Manual Transmission



c.
U165443E01
0.078,0.031 0.266,0.189 0.189,0.158 10 *a 0.543,1.673 1.040,1.831 0.497,0.158 10 NE 1.156,1.054 0.979,1.744 0.979,1.744 0.844,1.744 false 1.481,0.126 1.894,0.284 0.413,0.158 10 E128

Check the engine speed input signal waveform at the terminal of the certification ECU.

Standard Frequency:
Tester Connection Condition Specified Condition
E128-14 (NE) - Body ground Engine stopped No pulse generated
Engine running Pulse generated


Text in Illustration
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))

Result
Result Proceed to
OK A
NG for SFI system B
for ECD system C

HINT:

·

For the ECD SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING), refer to the following:






A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

GO TO SFI SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

C

GO TO ECD SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)