Home › Vehicle Exterior › WINDOW / GLASS › BACK WINDOW GLASS › from 2017.08
RM2660E _59 Vehicle Exterior _052850 WINDOW / GLASS _0255723 BACK WINDOW GLASS A

WINDOW / GLASS  BACK WINDOW GLASS  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 28800 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 67939B 3.REMOVE CENTER BACK DOOR GARNISH

Hide 67938A 4.REMOVE BACK DOOR SIDE GARNISH LH

Hide 67937B 5.REMOVE BACK DOOR SIDE GARNISH RH

Hide 67935B 6.REMOVE BACK DOOR GARNISH

Hide 64886B 7.REMOVE BACK DOOR GLASS CHANNEL LH (w/ Rear Spoiler)

B449337

a.

Using a clip remover, remove the clip.


b.

Remove the back door glass channel LH.


Hide 64885C 8.REMOVE BACK DOOR GLASS CHANNEL RH (w/ Rear Spoiler)

B449338

a.

Using a clip remover, remove the clip.


b.

Remove the back door glass channel RH.


Hide 76085 9.REMOVE REAR SPOILER SUB-ASSEMBLY (w/ Rear Spoiler)

Hide 10.REMOVE REAR WIPER ARM AND BLADE ASSEMBLY (w/ Rear Wiper)

Hide 85143R 11.REMOVE REAR WIPER MOTOR GROMMET (w/ Rear Wiper)

Hide 85110R 12.REMOVE REAR WIPER MOTOR ASSEMBLY (w/ Rear Wiper)

Hide 75574B 13.REMOVE BACK WINDOW MOULDING OUTSIDE LH

B436539E01
2.093,0.612 2.338,0.821 0.246,0.209 10 *a

Text in Illustration
*a Cut

a.

Using a knife, cut off the moulding as shown in the illustration.

NOTICE:

Be careful not to damage the vehicle body.



b.

Pull the shaded area shown in the illustration by the hand to remove the back window moulding outside.

HINT:

Make a partial cut in the moulding. Then pull and remove it by hand.



Hide 75573C 14.REMOVE BACK WINDOW MOULDING OUTSIDE

B436540E01
1.277,0.428 1.502,0.593 0.225,0.165 10 *a

Text in Illustration
*a Cut

a.

Using a knife, cut off the moulding as shown in the illustration.

NOTICE:

Be careful not to damage the vehicle body.



b.

Pull the shaded area shown in the illustration by the hand to remove the back window moulding outside.

HINT:

Make a partial cut in the moulding. Then pull and remove it by hand.



Hide 64811 15.REMOVE BACK WINDOW GLASS

a.
B436541E01
0.659,0.766 0.46,0.682 false 0.228,0.573 0.440,0.766 0.211,0.193 10 *1

Text in Illustration
*1 Protective Tape

Apply protective tape to the outer surface of the vehicle body to prevent scratches.

NOTICE:

When separating the back window glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.



b.

Disconnect the connectors.


c.
B180598E05
0.635,0.708 0.354,0.146 0.354,0.146 0.573,0.146 false 2.833,0.719 3.115,0.146 3.115,0.146 2.896,0.146 false 0.427,1.448 0.156,1.875 0.156,1.875 0.49,1.875 false 3.052,1.469 3.323,1.896 3.323,1.896 3,1.896 false 1.073,0.74 1.073,1.146 1.073,1.146 1.302,1.146 false 0.667,0.073 0.958,0.25 0.292,0.177 10 false *1 2.625,0.083 2.917,0.26 0.292,0.177 10 false *1 0.552,1.802 1.073,2.031 0.521,0.229 10 false *3 2.531,1.813 3.052,2.042 0.521,0.229 10 false *3 1.375,1.073 2.25,1.25 0.875,0.177 10 false *2

Text in Illustration
*1 Clip
*2 Piano Wire
*3 Spacer

From the interior, insert a piano wire between the vehicle body and back window glass as shown in the illustration.

NOTICE:

Make sure not to damage the wire harness.



d.

Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.


e.
U156039E01
0.199,0.516 0.476,0.737 0.277,0.221 10 *a

Text in Illustration
*a Matchmarks

Place matchmarks over the glass and vehicle body on the locations indicated in the illustration.

HINT:

Matchmarks do not need to be placed if the glass is not going to be reused.



f.

Cut through the adhesive by pulling the piano wire around the back window glass.

NOTICE:

Leave as much adhesive on the vehicle body as possible when removing the back window glass.



g.
B436543E01
0.57,0.775 0.288,0.619 false 0.056,0.507 0.277,0.700 0.220,0.193 10 *a

Text in Illustration
*a Matchmarks

Using suction cups, remove the back window glass.


Hide 16.CLEAN VEHICLE BODY

B106081E35
0.49,1.323 0.771,0.75 0.771,0.75 0.948,0.75 false 2.271,1.438 2.552,0.74 2.552,0.74 2.719,0.74 false 0.969,0.667 1.208,0.865 0.24,0.198 10 false *1 2.75,0.646 2.99,0.844 0.24,0.198 10 false *1

Text in Illustration
*a Adhesive

a.

Using a scraper, remove the moulding and adhesive from the back window glass.


b.

Clean and shape the contact surface of the vehicle body.

i.

On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

HINT:

Leave as much adhesive on the vehicle body as possible.


NOTICE:

Be careful not to damage the vehicle body.



ii.

Clean the contact surface of the vehicle body with cleaner.

HINT:

Even if all the adhesive has been removed, clean the vehicle body.