Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR › 2017.08–2019.08
RM2660E _59 Vehicle Exterior _052852 DOOR / HATCH _0255743 BACK DOOR A

DOOR / HATCH  BACK DOOR  DISASSEMBLY  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 69195 3.REMOVE BACK DOOR GRIP

a.
B309321

Using a moulding remover, detach the 5 claws and open the cover.


b.
B309322

Using a T30 "TORX" wrench, remove the 2 screws.


c.

Detach the claw and remove the back door grip.


Hide 69478 4.REMOVE LOWER BACK DOOR STOPPER CUSHION

a.
B232127

Remove the 4 bolts and 2 lower back door stopper cushions.


Hide 67939B 5.REMOVE CENTER BACK DOOR GARNISH

a.
B313300

Detach the 5 clips and 4 claws, and remove the center back door garnish.


b.

Disconnect the connector.


Hide 67938A 7.REMOVE BACK DOOR SIDE GARNISH LH

a.
B313301

Detach the 3 clips and 2 claws, and remove the back door side garnish LH.


Hide 67937B 8.REMOVE BACK DOOR SIDE GARNISH RH

a.

w/o Power Back Door:

HINT:

Use the same procedure described for the LH side.



b.
B313302

w/ Power Back Door:

i.

Detach the clip and 4 claws, and remove the back door side garnish RH.



Hide 67847 9.REMOVE BACK DOOR SERVICE HOLE COVER RH (w/ Power Back Door)

a.
B309323E02
2.271,1.292 2.542,1.073 false 2.708,1.49 2.542,1.385 false 1.333,0.375 1.583,0.583 0.25,0.208 10 false *a 2.115,1.26 2.365,1.469 0.25,0.208 10 false *2 2.76,1.448 3.01,1.656 0.25,0.208 10 false *1

Move the back door to a half-open position so that the hole in the center of the back door service hole cover RH is aligned lengthwise with the power back door rod.

Text in Illustration
*1 Power Back Door Rod
*2 Hole of Back Door Service Hole Cover RH
*a Back Door is Half-open


b.
B449415

Detach the 2 clips and separate the back door service hole cover RH, passing the power back door rod through the hole of the back door service hole cover RH.

NOTICE:

If the back door is in a fully-open position, the power back door rod will interfere with the hole of the back door service hole cover RH, so do not perform this operation with the back door in a fully open position.


HINT:

If any of the clips have remained on the back door, remove the clips from the back door and install them to the back door service hole cover RH.



c.
B193888

Remove the ball joint bolt, power back door rod and back door stay plate.


d.

Remove the back door service hole cover RH from the power back door rod.


Hide 67935B 10.REMOVE BACK DOOR GARNISH

a.
B433879

Using a clip remover, detach the 14 clips and remove the back door garnish.


Hide 86160T 11.REMOVE REAR HEADER SPEAKER ASSEMBLY (for 14 Speakers)

Hide 84280D 12.REMOVE POWER BACK DOOR SENSOR ASSEMBLY LH (w/ Power Back Door)

Hide 84270G 13.REMOVE POWER BACK DOOR SENSOR ASSEMBLY RH (w/ Power Back Door)

HINT:

Use the same procedure described for the LH side.


Hide 14.REMOVE REAR WIPER ARM AND BLADE ASSEMBLY (w/ Rear Wiper)

Hide 85143R 15.REMOVE REAR WIPER MOTOR GROMMET (w/ Rear Wiper)

Hide 85110R 16.REMOVE REAR WIPER MOTOR ASSEMBLY (w/ Rear Wiper)

Hide 69321 17.REMOVE BACK DOOR LOCK COVER

Hide 69350 18.REMOVE BACK DOOR LOCK ASSEMBLY

Hide 84930 19.REMOVE DOOR CONTROL SWITCH ASSEMBLY (w/ Power Back Door)

Hide 20.REMOVE LICENSE PLATE LIGHT ASSEMBLY (for Standard)

Hide 84840G 21.REMOVE BACK DOOR OPENER SWITCH ASSEMBLY

Hide 86790D 22.REMOVE REAR TELEVISION CAMERA ASSEMBLY (w/ Parking Assist Monitor System or Rear View Monitor System)

Hide 68281B 23.REMOVE LIFT GATE WEATHERSTRIP

a.
B449416

Detach the 25 clips and remove the lift gate weatherstrip.

NOTICE:

Do not pull strongly on the lift gate weatherstrip as it may tear.



Hide 24.REMOVE CUSHION

a.
B232921

Remove the 2 cushions.


Hide 67281F 25.REMOVE LOWER BACK DOOR STOPPER

a.
B192431

Remove the bolt and lower back door stopper.


Hide 81590A 26.REMOVE REAR LIGHT ASSEMBLY LH

Hide 81580D 27.REMOVE REAR LIGHT ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 76801B 28.REMOVE BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY

Hide 64886B 29.REMOVE BACK DOOR GLASS CHANNEL LH (w/o Power Back Door)

Hide 64885C 30.REMOVE BACK DOOR GLASS CHANNEL RH (w/o Power Back Door)

HINT:

Use the same procedure described for the LH side.


Hide 76085 31.REMOVE REAR SPOILER SUB-ASSEMBLY (w/ Rear Spoiler)

Hide 85345R 32.REMOVE REAR WASHER NOZZLE (w/ Rear Wiper)

Hide 68960 33.REMOVE BACK DOOR STAY ASSEMBLY LH

Hide 68950C 34.REMOVE BACK DOOR STAY ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 64894 36.REMOVE BACK DOOR TRIM COVER LH

a.
B313304

Remove the back door trim cover LH as shown in the illustration.


Hide 64893 37.REMOVE BACK DOOR TRIM COVER RH

a.
B313305

Remove the back door trim cover RH as shown in the illustration.


Hide 64780A 38.REMOVE BACK DOOR TRIM PANEL ASSEMBLY

a.
B181336

Remove the 4 bolts.


b.

Detach the 16 clips and remove the back door trim panel assembly.


Hide 76802C 39.REMOVE NO. 2 BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY (w/ Tire Carrier)

Hide 81270 40.REMOVE LICENSE PLATE LIGHT ASSEMBLY (w/ Tire Carrier)

Hide 75132C 41.REMOVE REAR LICENSE LIGHT COVER (w/ Tire Carrier)

Hide 42.REMOVE REAR BUMPER ASSEMBLY

a.

for Standard:

i.


b.

w/ Towing Hitch:



c.

w/ Pintle Hook:



Hide 43.REMOVE SPARE TIRE

Hide 68870 44.REMOVE LOWER BACK DOOR TORSION BAR ASSEMBLY

a.
B309324

Remove the 4 bolts and lower back door torsion bar assembly.


Hide 68846B 45.REMOVE BACK DOOR TORSION BAR GUIDE

a.
B181476

Detach the 2 claws and remove the back door torsion bar guide.


Hide 69291 46.REMOVE BACK DOOR INSIDE HANDLE ASSEMBLY

a.
B181339E04
0.865,1.385 1.083,1.375 1.083,1.375 1.708,1.135 true 0.625,1.302 0.823,1.51 0.198,0.208 10 false *1

Remove the screw and back door inside handle.

Text in Illustration
*1 Back Door Handle Grommet


b.

Remove the back door handle grommet.


Hide 69380A 47.REMOVE LOWER TAIL GATE LOCK ASSEMBLY RH

a.

w/o Power Back Door:

i.
B184140

Using a T30 "TORX" wrench, remove the 3 screws and lower tail gate lock assembly RH.


ii.
B184137

Disconnect the cable from the lower tail gate lock assembly RH.



b.

w/ Power Back Door:

i.
B193800

Disconnect the connector.


ii.
B232132

Using a T30 "TORX" wrench, remove the 4 screws and lower tail gate lock assembly RH.



Hide 69690 48.REMOVE BACK DOOR REMOTE CONTROL ASSEMBLY

a.

w/o Power Back Door:

i.
B184087

Remove the 2 screws.


ii.
B181340

Disconnect the left side cable.


iii.

Remove the back door remote control assembly.



b.

w/ Power Back Door:

i.
B191287

Disconnect the connector.


ii.

Remove the 2 screws and back door remote control assembly.



Hide 69390A 49.REMOVE LOWER TAIL GATE LOCK ASSEMBLY LH

a.

w/o Power Back Door:

i.
B181341

Using a T30 "TORX" wrench, remove the 3 screws and lower tail gate lock assembly LH.



b.

w/ Power Back Door:

i.
B191286

Disconnect the connector.


ii.
B232185

Using a T30 "TORX" wrench, remove the 4 screws and lower tail gate lock assembly LH.



Hide 65707A 50.REMOVE TAIL GATE STAY SUB-ASSEMBLY LH

a.
B181343

Using a T40 "TORX" socket, remove the 2 screws and tail gate stay sub-assembly LH.


Hide 65706A 51.REMOVE TAIL GATE STAY SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 67290 52.REMOVE BACK DOOR DAMPER ASSEMBLY (w/ Power Back Door)

a.
B191284

Remove the bolt and back door damper assembly.