Home › Vehicle Exterior › WINDOW / GLASS › BACK WINDOW GLASS › from 2017.08
RM2660E _59 Vehicle Exterior _052850 WINDOW / GLASS _0255723 BACK WINDOW GLASS A

WINDOW / GLASS  BACK WINDOW GLASS  INSTALLATION  


PROCEDURE

Hide 68131 1.CLEAN BACK DOOR GLASS

a.

Using a scraper, remove the damaged clips, spacers and adhesive sticking to the glass.


b.
B180599

Clean the outer circumference of the glass with non-residue solvent.

NOTICE:
·

Do not touch the glass surface after cleaning it.

·

Be careful not to damage the glass.

·

Even if using new glass, clean the glass with non-residue solvent.




Hide 64827A 2.INSTALL BACK WINDOW GLASS CLIP RH

a.

Apply Primer G to the glass where the clip will be installed.

HINT:

If the Primer G is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.



b.
B185857E05
1.656,0.271 2.052,0.219 false 2.135,0.135 2.427,0.375 0.292,0.24 10 false *b 0.094,0.073 0.385,0.313 0.292,0.24 10 false *a

Text in Illustration
*a Back of Back Window Glass
*b Marking for Clip Pasting

Remove the peeling paper from a new clip. Install a new clip onto the glass as shown in the illustration.

NOTICE:
·

Allow the Primer G to dry for 3 minutes or more.

·

Throw away any leftover Primer G.

·

Do not apply too much Primer G.




Hide 64828 3.INSTALL BACK WINDOW GLASS CLIP LH

a.

Apply Primer G to the glass where the clip will be installed.

HINT:

If the Primer G is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.



b.
B185858E05
1.573,0.438 1.938,0.271 false 0.094,0.115 0.396,0.344 0.302,0.229 10 false *a 1.365,0.365 1.667,0.594 0.302,0.229 10 false *b

Text in Illustration
*a Back of Back Window Glass
*b Marking for Clip Pasting

Remove the peeling paper from a new clip. Install a new clip onto the glass as shown in the illustration.

NOTICE:
·

Allow the Primer G to dry for 3 minutes or more.

·

Throw away any leftover Primer G.

·

Do not apply too much Primer G.




Hide 64818B 4.INSTALL NO. 1 BACK WINDOW GLASS SPACER

a.

Apply Primer G to the glass where the spacer will be installed.

HINT:

If the Primer G is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.



b.
B185859E04
1.646,0.25 1.979,0.198 false 2.031,0.104 2.281,0.323 0.25,0.219 10 false *b 0.094,0.063 0.344,0.281 0.25,0.219 10 false *a

Text in Illustration
*a Back of Back Window Glass
*b Marking for Clip Pasting

Remove the peeling paper from a new spacer. Install a new spacer onto the glass as shown in the illustration.

NOTICE:
·

Allow the Primer G to dry for 3 minutes or more.

·

Throw away any leftover Primer G.

·

Do not apply too much Primer G.




Hide 64819B 5.INSTALL NO. 2 BACK WINDOW GLASS SPACER

a.

Apply Primer G to the glass where the spacer will be installed.

HINT:

If the Primer G is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.



b.
B185860E05
1.885,0.344 2.25,0.271 false 0.125,0.115 0.396,0.365 0.271,0.25 10 false *a 1.677,0.25 1.948,0.5 0.271,0.25 10 false *b

Text in Illustration
*a Back of Back Window Glass
*b Marking for Clip Pasting

Remove the peeling paper from a new spacer. Install a new spacer onto the glass as shown in the illustration.

NOTICE:
·

Allow the Primer G to dry for 3 minutes or more.

·

Throw away any leftover Primer G.

·

Do not apply too much Primer G.




Hide 75573C 6.INSTALL BACK WINDOW OUTSIDE MOULDING

a.
B180601E05
1.052,2.146 1.458,2.365 0.406,0.219 10 false A - A 0.26,0.833 0.427,0.969 0.167,0.135 10 false A 0.573,0.906 0.74,1.042 0.167,0.135 10 false A 2.885,1.271 3.052,1.406 0.167,0.135 10 false A 3.219,1.198 3.385,1.333 0.167,0.135 10 false A 1.938,2.25 2.104,2.417 0.167,0.167 10 false a 0.104,0.094 0.448,0.438 0.344,0.344 10 false *a 0.844,3.083 1.26,3.354 0.417,0.271 10 false *1

Using a brush or sponge, coat the application area of the back window glass outside moulding with Primer G.

Text in Illustration
*a Back of Back Window Glass
*1 Primer G

Standard:
Area Specified Condition
a 13.0 mm (0.512 in.)


NOTICE:
·

Allow the Primer G to dry for 3 minutes or more.

·

Throw away any leftover Primer G.

·

Do not apply too much Primer G.



HINT:

If the Primer G is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.



b.

Remove the peeling paper from 2 new back window outside mouldings. Install the 2 mouldings as shown in the illustration.

B180602E05
0.563,2.292 1.104,2.365 false 5.229,2.292 4.688,2.365 false 0.583,0.49 1.688,0.458 false 5.25,0.479 4.625,0.396 false 0.479,0.135 0.625,0.333 0.146,0.198 10 false a 0.354,1.885 0.5,2.083 0.146,0.198 10 false b 6.448,0.979 6.594,1.177 0.146,0.198 10 false c 5.271,0.146 5.417,0.344 0.146,0.198 10 false a 5.396,1.906 5.542,2.104 0.146,0.198 10 false b 5.906,0.865 6.323,1.073 0.417,0.208 10 false A - A 1.156,0.938 1.323,1.104 0.167,0.167 10 false A 1.542,1.042 1.708,1.208 0.167,0.167 10 false A 4.271,1.49 4.438,1.656 0.167,0.167 10 false A 4.656,1.375 4.823,1.542 0.167,0.167 10 false A 0.052,0.031 0.365,0.24 0.313,0.208 10 false *a 1.75,0.354 2.146,0.646 0.396,0.292 10 false *b 4.406,0.281 4.646,0.5 0.24,0.219 10 false *b 1.177,2.281 1.573,2.573 0.396,0.292 10 false *b 4.438,2.281 4.833,2.573 0.396,0.292 10 false *b

Text in Illustration
*a Back of Back Window Glass *b R End

Standard:
Area Specified Condition
a 1.5 mm (0.0591 in.)
b 1.0 mm (0.0394 in.)
c 11.0 mm (0.433 in.)



Hide 64811 7.INSTALL BACK WINDOW GLASS

B436544E03
2.417,1.021 2.063,0.802 false 2.375,2 1.969,1.771 false 2.333,2.156 2.188,2.302 2.188,2.302 1.938,2.302 false 1.698,0.083 1.927,0.302 0.229,0.219 10 false *a 1.76,2.417 1.99,2.635 0.229,0.219 10 false *b 1.833,0.698 2.063,0.917 0.229,0.219 10 false *1 1.771,1.667 2,1.885 0.229,0.219 10 false *1 1.76,2.208 1.99,2.427 0.229,0.219 10 false *2 0.698,4.323 0.927,4.542 0.229,0.219 10 false : *1

Text in Illustration
*1 Primer M
*2 Adhesive
*a CORRECT
*b INCORRECT

a.

Using a brush or sponge, apply Primer M to the exposed part of the vehicle body.

NOTICE:
·

Allow the Primer M to dry for 3 minutes or more.

·

Do not apply Primer M to the adhesive.

·

Throw away any leftover Primer M.

·

Do not apply too much Primer M.




b.

Using a brush or sponge, apply Primer G to the contact surface of the back window glass.

B180604E06
2.979,2.5 2.979,2.698 false 4.865,1.063 5.354,1.635 5.354,1.635 6.281,1.021 false 6.396,2.542 5.479,3.323 5.479,3.323 4.875,2.719 false 5.479,3.323 6.552,2.531 false 1.844,1.208 2,1.375 0.156,0.167 10 false A 1.833,1.625 1.99,1.792 0.156,0.167 10 false A 0.75,1.833 0.906,2 0.156,0.167 10 false D 0.375,1.708 0.531,1.875 0.156,0.167 10 false D 3.958,1.833 4.115,2 0.156,0.167 10 false B 3.385,2.083 3.5,2.281 0.115,0.198 10 true B 1.271,2.208 1.427,2.375 0.156,0.167 10 false C 1.26,2.594 1.417,2.76 0.156,0.167 10 false C 4.281,0.313 4.646,0.479 0.365,0.167 10 false A - A 5.823,0.323 6.188,0.49 0.365,0.167 10 false B - B 4.406,2.052 4.771,2.219 0.365,0.167 10 false C - C 5.844,2.052 6.208,2.219 0.365,0.167 10 false D - D 4.354,0.833 4.542,1.042 0.188,0.208 10 false a 4.292,2.771 4.479,2.979 0.188,0.208 10 false c 6.427,2.844 6.615,3.052 0.188,0.208 10 false b 6.292,1.635 6.479,1.844 0.188,0.208 10 false d 6.281,3.24 6.469,3.448 0.188,0.208 10 false d 0.094,0.073 0.458,0.438 0.365,0.365 10 false *a 5.292,1.656 5.656,2.021 0.365,0.365 10 false *b 5.427,3.344 5.792,3.708 0.365,0.365 10 false *b 2.927,2.719 3.292,3.083 0.365,0.365 10 false *b 0.708,3.521 1.104,3.781 0.396,0.26 10 false *1

Text in Illustration
*1 Primer G - -
*a Back of Back Window Glass *b Adhesive Center Line

Standard:
Area Specified Condition
a 11.0 mm (0.433 in.)
b 8.0 mm (0.315 in.)
c 13.0 mm (0.512 in.)
d 5.0 mm (0.197 in.)


HINT:

If Primer G is applied to an area that is not specified, wipe off the Primer G with a non-residue solvent before it dries.


NOTICE:
·

Allow the Primer G to dry for 3 minutes or more.

·

Throw away any leftover Primer G.

·

Do not apply too much Primer G.




c.

Apply adhesive to the back window glass.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or equivalent


i.

Cut off the tip of the cartridge nozzle as shown in the illustration below.

HINT:

After cutting off the tip, use all adhesive within the time written in the table below.


Usage Time Frame:
Temperature Usage Time Frame
35°C (95°F) 15 minutes
20°C (68°F) 1 hour 40 minutes
5°C (41°F) 8 hours



ii.

Load the sealer gun with the cartridge.


iii.

Apply adhesive to the back window glass as shown in the illustration.

B188665E05
2.698,1.698 2.698,1.896 false 4.5,1.021 4.833,1.427 false 6.51,1.396 6.219,1.083 false 6.115,2.594 4.958,3.229 4.958,3.229 4.667,2.781 false 6.281,2.594 4.958,3.229 false 1.646,0.417 1.802,0.583 0.156,0.167 10 false A 1.667,0.823 1.823,0.99 0.156,0.167 10 false A 0.573,1 0.729,1.167 0.156,0.167 10 false D 0.219,0.885 0.375,1.052 0.156,0.167 10 false D 3.813,1.073 3.969,1.24 0.156,0.167 10 false B 3.167,1.292 3.323,1.458 0.156,0.167 10 true B 1.073,1.406 1.229,1.573 0.156,0.167 10 false C 1.073,1.792 1.229,1.958 0.156,0.167 10 false C 4.125,0.104 4.49,0.271 0.365,0.167 10 false A - A 5.594,0.094 5.958,0.26 0.365,0.167 10 false B - B 4.01,1.833 4.375,2 0.365,0.167 10 false C - C 5.531,1.771 5.896,1.938 0.365,0.167 10 false D - D 2.667,2.552 2.854,2.76 0.188,0.208 10 false a 0.583,3.135 0.771,3.344 0.188,0.208 10 false a 4.385,1.594 4.521,1.781 0.135,0.188 10 false a 4.5,1.958 4.677,2.188 0.177,0.229 10 false a 6.781,2.625 6.906,2.823 0.125,0.198 10 false a 3.167,2.667 3.354,2.875 0.188,0.208 10 false b 0.958,2.688 1.146,2.896 0.188,0.208 10 false b 5.219,2.594 5.406,2.802 0.188,0.208 10 false b 5.01,0.917 5.156,1.104 0.146,0.188 10 false b 5.49,1.115 5.635,1.302 0.146,0.188 10 false a 6.156,0.354 6.344,0.563 0.188,0.208 10 false b 6.073,1.906 6.26,2.115 0.188,0.208 10 false b 6.188,2.969 6.375,3.177 0.188,0.208 10 false b 6.042,3.281 6.229,3.49 0.188,0.208 10 false e 3.979,0.781 4.167,0.99 0.188,0.208 10 false c 4.083,2.844 4.271,3.052 0.188,0.208 10 false d 6.219,1.677 6.406,1.885 0.188,0.208 10 false e 0.104,0.083 0.51,0.375 0.406,0.292 10 false *a 4.844,1.396 5.25,1.688 0.406,0.292 10 false *b 6.563,1.344 6.969,1.635 0.406,0.292 10 false *b 4.917,3.26 5.323,3.552 0.406,0.292 10 false *b 1.385,3.188 1.792,3.479 0.406,0.292 10 false *c 2.625,1.938 3.031,2.229 0.406,0.292 10 false *b

Text in Illustration
*a Back of Back Window Glass *b Adhesive Center Line
*c Adhesive - -

Standard:
Area Specified Condition
a 12.0 mm (0.472 in.)
b 8.0 mm (0.315 in.)
c 11.0 mm (0.433 in.)
d 13.0 mm (0.512 in.)
e 5.0 mm (0.197 in.)




d.

Install the back window glass to the vehicle body.

i.

Hold the back window glass securely in place with tape or equivalent until the adhesive has hardened.

NOTICE:
·

Allow the Primer G coating to dry for 3 minutes or more.

·

Check that the clips are attached to the vehicle body correctly.

·

Check the clearance between the vehicle body and glass.




ii.

Lightly press the front surface of the back window glass to ensure that the back window glass is securely fit to the vehicle body.


iii.
B180606E05
1.756,1.426 1.979,1.623 0.223,0.198 10 *a 0.978,1.467 1.709,1.525 false

Text in Illustration
*a Adhesive

Using a scraper, remove any excess or protruding adhesive.

HINT:

Apply adhesive onto the glass rim.


NOTICE:

Do not drive the vehicle within the time written in the table below.


Minimum time:
Temperature Minimum Time Prior to Driving Vehicle
35°C (95°F) 1 hour 30 minutes
20°C (68°F) 5 hours
5°C (41°F) 24 hours



iv.

Connect the connectors.



Hide 85110R 8.INSTALL REAR WIPER MOTOR ASSEMBLY (w/ Rear Wiper)

Hide 85143R 9.INSTALL REAR WIPER MOTOR GROMMET (w/ Rear Wiper)

Hide 10.INSTALL REAR WIPER ARM AND BLADE ASSEMBLY (w/ Rear Wiper)

Hide 68131 11.CHECK FOR LEAK AND REPAIR

a.

Conduct a leak test after the adhesive has completely hardened.


b.

Seal any leaks with auto glass sealer.


Hide 76085 12.INSTALL REAR SPOILER SUB-ASSEMBLY (w/ Rear Spoiler)

Hide 64886B 13.INSTALL BACK DOOR GLASS CHANNEL LH

B449337

a.

Attach the clip and install the back door glass channel.


Hide 64885C 14.INSTALL BACK DOOR GLASS CHANNEL RH

B449338

a.

Attach the clip and install the back door glass channel.


Hide 67935B 15.INSTALL BACK DOOR GARNISH

Hide 67938A 16.INSTALL BACK DOOR SIDE GARNISH LH

Hide 67937B 17.INSTALL BACK DOOR SIDE GARNISH RH

Hide 67939B 18.INSTALL CENTER BACK DOOR GARNISH

Hide 19.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).