The radio and display receiver assembly receives a reverse signal from the park/neutral position switch assembly*1 or back-up light switch assembly*2.
*1: for Automatic Transmission
*2: for Manual Transmission
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
When replacing the radio and display receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services (w/ Connected Services Function).
Enter the "Vehicle Signal Check Mode" screen. [Refer to check Vehicle Signal in Operation Check (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>OPERATION CHECK)]
Check that the display changes between ON and OFF according to the shift lever position.
| Shift Lever Position | Display |
|---|---|
| R | ON |
| Except R | OFF |
This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever position.
OK
NG
Disconnect the radio and display receiver assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F124-2 (REV) - Body ground | Engine switch on (IG), shift lever in R | 7.5 to 14 V |
| F124-2 (REV) - Body ground | Engine switch on (IG), shift lever not in R | Below 1 V |
| *a | Front view of wire harness connector
(to Radio and Display Receiver Assembly) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for Automatic Transmission) | B |
| NG (for Manual Transmission) | C |
A
B
C
Disconnect the F124 radio and display receiver assembly connector.
Disconnect the C24 park/neutral position switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F124-2 (REV) - C24-1 (RL) | Always | Below 1 Ω |
| F124-2 (REV) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the park/neutral position switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C24-2 (RB) - Body ground | Engine switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector
(to Park/neutral Position Switch Assembly) |
| Result | Proceed to |
|---|---|
| OK (for AB60F) | A |
| OK (for AE80F) | B |
| NG | C |
A
(See pageDrivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL)
B
(See pageDrivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL)
C
Disconnect the F124 radio and display receiver assembly connector.
Disconnect the C39 back-up light switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F124-2 (REV) - C39-1 | Always | Below 1 Ω |
| F124-2 (REV) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the back-up light switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C39-2 - Body ground | Engine switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector
(to Back-up Light Switch Assembly) |
OK
NG