Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (w/ Multi-display) › from 2018.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255488 AUDIO AND VISUAL SYSTEM(w/ Multi-display) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(w/ Multi-display)  Display Signal Circuit between Multi-display and Radio Receiver  


DESCRIPTION

The display image signal from the multi-media module receiver assembly is sent to the multi-display assembly using a digital communication cable.

WIRING DIAGRAM

E349092E02
1.188,3.26 2.365,3.458 1.177,0.198 10 false : GVIF Cable 0.594,2.979 1.531,3.208 0.938,0.229 10 false *: Shielded 0.917,2.094 1.458,2.323 0.542,0.229 10 false F139 0.896,2.281 2.563,2.552 1.667,0.271 10 false Multi-display Assembly 1.635,0.729 2.031,0.99 0.396,0.26 10 false GVI+ 1.646,1.167 2.031,1.438 0.385,0.271 10 false GVI- 1.563,1.615 2,1.844 0.438,0.229 10 false GVG1 2.063,0.604 2.271,0.844 0.208,0.24 10 false 1 2.073,1.021 2.26,1.198 0.188,0.177 10 false 2 2.063,1.521 2.25,1.698 0.188,0.177 10 false 3 3.823,1.76 4.01,1.938 0.188,0.177 10 false * 5.74,0.698 6.177,0.948 0.438,0.25 10 false GV+ 5.76,1.146 6.208,1.417 0.448,0.271 10 false GV- 5.74,1.625 6.302,1.938 0.563,0.313 10 false GVG 5.5,0.604 5.708,0.844 0.208,0.24 10 false 1 5.51,1.031 5.698,1.208 0.188,0.177 10 false 2 5.5,1.49 5.688,1.667 0.188,0.177 10 false 3 5.542,2.083 6.01,2.292 0.469,0.208 10 false F107 5.552,2.271 6.833,2.792 1.281,0.521 10 false Multi-media Module Receiver Assembly

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (GVIF CABLE)
a.

Check if the GVIF cable connectors between the multi-media module receiver assembly and the multi-display assembly have any connection problems.

OK:

There is no connection problems.




OK

2.CHECK HARNESS AND CONNECTOR (GVIF CABLE)

NG

REMOVE CONNECTION PROBLEM (GVIF CABLE)

2.CHECK HARNESS AND CONNECTOR (GVIF CABLE)
a.
E402588E03
1.938,1.052 2.031,1.583 2.031,1.583 2.177,1.583 true 1.302,1.542 1.448,1.542 1.448,1.542 1.75,0.854 true 2.354,0.302 2.198,0.302 2.198,0.302 2,0.844 true 1.594,2.563 1.646,1.917 1.646,1.917 1.802,1.917 true 1.521,2.906 1.625,3.302 1.625,3.302 1.76,3.302 true 1.292,2.583 0.99,2.26 0.99,2.26 0.802,2.26 true 0.229,1.875 0.427,2.125 0.198,0.25 10 false *b 0.229,0.083 0.427,0.333 0.198,0.25 10 false *a 0.448,2.552 0.854,2.74 0.406,0.188 10 false F107 0.76,0.833 1.167,1.021 0.406,0.188 10 false F139 1.823,3.229 2.313,3.417 0.49,0.188 10 false GVG 0.479,2.167 0.969,2.354 0.49,0.188 10 false GV+ 1.854,1.833 2.344,2.021 0.49,0.188 10 false GV- 2.417,0.24 2.906,0.427 0.49,0.188 10 false GVI- 2.25,1.521 2.74,1.708 0.49,0.188 10 false GVG1 0.938,1.448 1.427,1.635 0.49,0.188 10 false GVI+

Disconnect the F139 multi-display assembly connector.


b.

Disconnect the F107 multi-media module receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F139-1 (GVI+) - F107-1 (GV+) Always Below 1 Ω
F139-2 (GVI-) - F107-2 (GV-) Always Below 1 Ω
F139-3 (GVG1) - F107-3 (GVG) Always Below 1 Ω
F139-1 (GVI+) - Body ground Always 10 kΩ or higher
F139-2 (GVI-) - Body ground Always 10 kΩ or higher
F139-3 (GVG1) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view or wire harness connector
(to Multi-display Assembly)
*b Front view or wire harness connector
(to Multi-media Module Receiver Assembly)



OK

3.CHECK MULTI-DISPLAY ASSEMBLY

NG

REPLACE HARNESS AND CONNECTOR (GVIF CABLE)

3.CHECK MULTI-DISPLAY ASSEMBLY
a.

Replace the multi-display assembly with a new or known good one (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>MULTI-DISPLAY (w/ Navigation System)>REMOVAL).


b.

Check that the screen display is normal.

OK:

Screen display is normal.




OK

END (MULTI-DISPLAY ASSEMBLY IS DEFECTIVE)

NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE