Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.
Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or use waterless hand cleaner, to remove any used engine oil thoroughly. Do not use gasoline, thinners, or solvents.
In order to protect the environment, used oil and used oil filters must be disposed of at designated disposal sites.
1.DRAIN ENGINE OIL
Remove the oil filler cap.
Remove the 2 bolts and No. 2 engine under cover seal.
Remove the oil pan drain plug and gasket, and drain the engine oil into a container.
Install a new gasket and the oil pan drain plug.
53806
2.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH
51405A
3.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY LH
Remove the 5 bolts and No. 1 engine under cover sub-assembly LH.
4.REMOVE OIL FILTER ELEMENT
Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.
| *1 | Pipe |
| *2 | Hose |
Remove the oil filter drain plug.
Install the pipe to the oil filter cap.
| *1 | Cap |
| *2 | Valve |
| *3 | Pipe |
| *4 | O-Ring |
| *5 | Hose |
If the O-ring is removed with the drain plug, install the O-ring together with the pipe.
Use a container to catch the draining oil.
Check that oil is drained from the oil filter. Then disconnect the pipe and remove the O-ring as shown in the illustration.
Using SST, remove the oil filter cap.
| *1 | Oil Filter Bracket Clip |
Do not remove the oil filter bracket clip.
Remove the oil filter element and O-ring from the oil filter cap.
| *1 | Oil Filter Element |
| *2 | O-Ring |
Be sure to remove the cap O-ring by hand, without using any tools, to prevent damage to the cap O-ring groove.
5.INSTALL OIL FILTER ELEMENT
Clean the inside of the oil filter cap, its threads and its O-ring groove.
Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap.
Set a new oil filter element to the oil filter cap.
Remove any dirt or foreign matter from the installation surface of the engine.
Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap.
Do not remove the oil filter bracket clip.
Using SST, tighten the oil filter cap.
| *1 | Oil Filter Bracket Clip |
When tightening the oil filter cap, do not remove the oil filter bracket clip.
Make sure that the oil filter is installed securely as shown in the illustration.
Be careful that the O-ring does not get caught between any surrounding parts.
Apply a small amount of engine oil to a new drain plug O-ring, and install it to the oil filter cap.
| *1 | O-Ring |
Before installing the O-ring, remove any dirt or foreign matter from the installation surface of the oil filter cap.
Install the oil filter drain plug.
Be careful that the O-ring does not get caught between any surrounding parts.
Install the No. 2 engine under cover seal with the 2 bolts.
6.ADD ENGINE OIL
Add fresh oil and install the oil filler cap.
| Oil Grade | Oil Viscosity (SAE) |
|---|---|
| API grade SL "energy-conserving", SM "energy-conserving", SN "resource-conserving", SN PLUS "resource-conserving" or ILSAC multigrade engine oil | 5W-30
10W-30 |
| API grade SL, SM, SN or SN PLUS multigrade engine oil | 15W-40
20W-50 |
| Item | Specified Condition |
|---|---|
| Drain and refill without oil filter change | 7.1 liters (7.5 US qts, 6.2 Imp. qts) |
| Drain and refill with oil filter change | 7.5 liters (7.9 US qts, 6.6 Imp. qts) |
| Dry fill | 9.3 liters (9.8 US qts, 8.2 Imp. qts) |
7.INSPECT FOR OIL LEAK
Start the engine. Make sure that there are no oil leaks from the area that was worked on.
8.INSPECT ENGINE OIL LEVEL
51405A
9.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY LH
Install the No. 1 engine under cover with the 5 bolts.
53806
10.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH