Home › Engine / Hybrid System › 1GR-FE (LUBRICATION) › OIL AND OIL FILTER › from 2019.08
RM2660E _51 Engine / Hybrid System _052798 1GR-FE LUBRICATION _0255215 OIL AND OIL FILTER A

1GR-FE LUBRICATION  OIL AND OIL FILTER  REPLACEMENT  


CAUTION / NOTICE / HINT

CAUTION:
·

Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

·

Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or use waterless hand cleaner, to remove any used engine oil thoroughly. Do not use gasoline, thinners, or solvents.

·

In order to protect the environment, used oil and used oil filters must be disposed of at designated disposal sites.



PROCEDURE

Hide 1.DRAIN ENGINE OIL

a.

Remove the oil filler cap.


b.

Remove the 2 bolts and No. 2 engine under cover seal.


c.

Remove the oil pan drain plug and gasket, and drain the engine oil into a container.


d.

Install a new gasket and the oil pan drain plug.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


e.

Install the No. 2 engine under cover seal with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 53806 2.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

Hide 51409B 3.REMOVE ENGINE UNDER COVER SUB-ASSEMBLY LH

a.
A272726

Remove the 6 bolts and No. 1 engine under cover sub-assembly LH.


Hide 4.REMOVE OIL FILTER ELEMENT

a.
A385997E01
0.938,0.625 1.375,0.25 false 2.323,1.49 2.76,1.115 false 1.438,0.125 1.75,0.323 0.313,0.198 10 false *1 2.792,0.948 3.104,1.146 0.313,0.198 10 false *2

Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.

Text in Illustration
*1 Pipe
*2 Hose


b.
A222100

Remove the oil filter drain plug.


c.
A272717E02
0.635,2.26 0.948,2.26 0.948,2.26 1.229,2.417 false 1.479,3.063 1.25,3.063 false 1.271,2.823 0.76,2.823 false 0.75,2.51 1.156,2.51 1.156,2.51 1.5,2.635 false 0.938,1.875 0.729,1.875 0.729,1.875 0.677,1.99 false 0.969,1.792 1.146,1.958 0.177,0.167 10 false *1 0.448,2.177 0.615,2.427 0.167,0.25 10 true *2 0.531,2.438 0.708,2.604 0.177,0.167 10 true *3 0.563,2.729 0.74,2.896 0.177,0.167 10 false *4 1.073,2.979 1.25,3.146 0.177,0.167 10 false *5

Install the pipe to the oil filter cap.

Text in Illustration
*1 Cap
*2 Valve
*3 Pipe
*4 O-Ring
*5 Hose

NOTICE:

If the O-ring is removed with the drain plug, install the O-ring together with the pipe.


HINT:

Use a container to catch the draining oil.



d.
A222102

Check that oil is drained from the oil filter. Then, disconnect the pipe and remove the O-ring as shown in the illustration.


e.
A222103E01
2.97,0.916 3.181,1.105 0.211,0.188 10 *1 2.545,1.003 2.945,1.003 false 2.83,1.375 3.146,1.543 0.316,0.169 10 SST 2.415,1.463 2.799,1.463 false

Using SST, remove the oil filter cap.

SST
09228-06501  

Text in Illustration
*1 Oil Filter Bracket Clip

NOTICE:

Do not remove the oil filter bracket clip.



f.
A153538E03
0.517,1.06 0.706,1.268 0.189,0.208 10 *1 1.029,1.146 0.735,1.146 false

Remove the oil filter element and O-ring from the oil filter cap.

Text in Illustration
*1 O-Ring

NOTICE:

Be sure to remove the O-ring (for the cap) by hand, without using any tools, to prevent damage to the groove for the O-ring in the cap.



Hide 5.INSTALL OIL FILTER ELEMENT

a.

Clean the inside of the oil filter cap, the threads and O-ring groove.


b.
A268595E01
1.674,0.732 1.835,0.881 0.162,0.149 10 *1 1.52,1.046 1.586,0.819 1.586,0.819 1.667,0.819 false 3.238,0.835 3.399,0.984 0.162,0.149 10 *1 3.089,1.16 3.15,0.922 3.15,0.922 3.231,0.922 false 0.873,1.8 1.038,1.952 0.165,0.152 10 *a 2.434,1.8 2.599,1.952 0.165,0.152 10 *b

Apply a light coat of engine oil to a new O-ring for the cap, and then install the O-ring to the groove of the oil filter cap.

Text in Illustration
*1 O-Ring
*a CORRECT
*b INCORRECT

NOTICE:
·

Be sure to install the O-ring in the proper location, otherwise oil may leak.

·

Do not twist the O-ring.




c.

Set a new oil filter element in the oil filter cap.


d.

Remove any dirt or foreign matter from the installation surface of the engine.


e.

Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap.

NOTICE:

Do not pinch the O-ring for the cap.



f.
A271363E01
1.724,2.412 1.896,2.560 0.172,0.148 10 *1 1.542,2.337 1.619,2.497 1.619,2.497 1.72,2.497 false 0.803,2.599 0.962,2.746 0.160,0.148 10 *2 1.152,2.407 1.074,2.69 1.074,2.69 0.984,2.69 false 0.294,2.696 0.454,2.844 0.160,0.148 10 *3 0.663,2.488 0.588,2.77 0.588,2.77 0.479,2.77 false 1.308,2.879 1.468,3.027 0.160,0.148 10 *a 2.557,2.341 2.858,2.500 0.301,0.158 10 SST 3,1.553 3.056,2.424 3.056,2.424 2.918,2.424 false

Using SST, tighten the oil filter cap.

SST
09228-06501  

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

Text in Illustration
*1 Oil Filter Cap
*2 O-Ring
*3 Oil Filter Bracket
*a No Gap

NOTICE:

After tightening the oil filter cap, make sure that there is no gap and that the O-ring is not protruding.



g.
A272718E01
0.53,2.633 0.688,2.788 0.158,0.155 10 *1 1.244,2.717 0.709,2.717 false

Apply a small amount of engine oil to a new drain plug O-ring and install the O-ring to the oil filter cap.

Text in Illustration
*1 O-Ring

NOTICE:

Before installing the O-ring, remove any dirt or foreign matter from the installation surface of the oil filter cap.



h.

Install the oil filter drain plug.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)

NOTICE:

Make sure that the O-ring does not get caught between the parts.



Hide 6.ADD ENGINE OIL

a.

Add fresh oil.

NOTICE:
A308107

Do not allow engine oil to adhere to the moving parts of the belt tensioner, as this may cause malfunctions.

If engine oil is on the location indicated by the arrow, replace the belt tensioner.


Standard Engine Oil:
Oil Grade Oil Viscosity (SAE)
API grade SL "energy-conserving", SM "energy-conserving", SN "resource-conserving", SN PLUS "resource-conserving" or ILSAC multigrade engine oil 5W-30
10W-30
API grade SL, SM, SN or SN PLUS multigrade engine oil 15W-40
20W-50


Standard Engine Oil (for China):
Oil Grade Oil Viscosity (SAE)
API grade SL "energy-conserving", SM "energy-conserving", SN "resource-conserving", SN PLUS "resource-conserving" or ILSAC multigrade engine oil 0W-20
5W-20
5W-30
10W-30
API grade SL, SM, SN or SN PLUS multigrade engine oil 15W-40
20W-50


Standard Oil Capacity:
Item Specified Condition
Drain and refill without oil filter change 5.6 liters (5.9 US qts, 4.9 Imp. qts)
Drain and refill with oil filter change 6.1 liters (6.4 US qts, 5.4 Imp. qts)
Dry fill 7.1 liters (7.5 US qts, 6.2 Imp. qts)



Hide 8.INSPECT FOR OIL LEAK

a.

Start the engine. Make sure that there are no oil leaks from the area that was worked on.


Hide 51409B 9.INSTALL ENGINE UNDER COVER SUB-ASSEMBLY LH

a.

Install the No. 1 engine under cover sub-assembly LH with the 5 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 53806 10.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH