Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2014.08–2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255415 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C0278  Open in ABS Solenoid Relay Circuit  C0279  Short in ABS Solenoid Relay Circuit  


DESCRIPTION

The solenoid relay is built into the master cylinder solenoid.

This relay supplies power to each solenoid. If the initial check is OK, after the ignition switch is turned to ON, the relay turns on.

DTC Code DTC Detection Condition Trouble Area
C0278 When either of the following conditions is detected:
1.

Both of the following conditions continue for at least 0.2 seconds.

(a)

IG voltage is between 9.5 V and 17 V.

(b)

The relay contact is open when the relay is on.


2.

Both of the following conditions continue for at least 0.2 seconds.

(a)

IG voltage is 9.5 V or less when the relay is on.

(b)

The relay contact remains open.



·

ABS2 fuse

·

Solenoid relay

·

Harness or connector

·

Skid control ECU (Master cylinder solenoid)


C0279 The following condition continues for at least 0.2 seconds.
·

The relay contact is closed immediately after turning the ignition switch to ON when the relay is off.


·

ABS2 fuse

·

Solenoid relay

·

Harness or connector

·

Skid control ECU (Master cylinder solenoid)



WIRING DIAGRAM

C182044E01
1.714,0.701 2.128,0.866 0.413,0.166 10 ABS2 2.886,0.329 3.07,0.494 0.184,0.166 10 31 2.928,5.919 3.03,6.085 0.102,0.166 10 1 2.889,6.478 3.073,6.644 0.184,0.166 10 32 2.928,7.033 3.056,7.198 0.128,0.166 10 4 3.22,0.651 3.557,0.816 0.337,0.166 10 +BS 6.177,1.228 6.514,1.394 0.337,0.166 10 STR 6.134,1.79 6.554,1.956 0.42,0.166 10 SREC 6.134,2.341 6.554,2.507 0.42,0.166 10 SFRH 6.134,2.895 6.554,3.06 0.42,0.166 10 SFLH 6.134,3.462 6.554,3.628 0.42,0.166 10 SRRH 6.134,4.019 6.554,4.185 0.42,0.166 10 SRLH 6.134,4.587 6.554,4.752 0.42,0.166 10 SFRR 6.134,5.683 6.554,5.848 0.42,0.166 10 SRRR 6.134,6.24 6.554,6.405 0.42,0.166 10 SRLR 6.134,6.797 6.554,6.962 0.42,0.166 10 SREA 6.134,7.357 6.554,7.523 0.42,0.166 10 SMCF 6.134,5.133 6.554,5.298 0.42,0.166 10 SFLR 3.242,6.141 3.697,6.306 0.455,0.166 10 GND1 3.239,6.69 3.694,6.856 0.455,0.166 10 GND2 3.242,7.254 3.697,7.42 0.455,0.166 10 GND3 2.832,0.537 3.141,0.703 0.309,0.166 10 A24 2.838,6.135 3.147,6.3 0.309,0.166 10 A24 2.834,6.694 3.144,6.86 0.309,0.166 10 A24 2.838,7.251 3.147,7.417 0.309,0.166 10 A25 0.806,6.996 1.31,7.161 0.503,0.166 10 Battery 4.134,0.46 5.11,0.626 0.976,0.166 10 Solenoid Relay 4.066,8.106 5.18,8.272 1.115,0.166 10 Skid Control ECU 4.276,8.488 5.9,8.653 1.624,0.166 10 Master Cylinder Solenoid

CAUTION / NOTICE / HINT

NOTICE:

When replacing the master cylinder solenoid, perform zero point calibration (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.INSPECT ABS2 FUSE
a.

Remove the ABS2 fuse from the engine room relay block.


b.
C176463E04
1.656,1.813 1.083,1.427 1.083,1.427 0.917,1.427 true 0.104,0.094 0.354,0.313 0.25,0.219 10 false *1 0.708,1.344 0.948,1.531 0.24,0.188 10 false *2

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ABS2 fuse Always Below 1 Ω


Text in Illustration
*1 Engine Room Relay Block
*2 ABS2 Fuse


Result:
Proceed to
OK
NG



OK

2.INSPECT SKID CONTROL ECU (+BS TERMINAL)

NG

REPLACE ABS2 FUSE

2.INSPECT SKID CONTROL ECU (+BS TERMINAL)
a.

Install the ABS2 fuse.


b.

Disconnect the A24 skid control ECU (master cylinder solenoid) connector.


c.
C214161E01
0.144,0.636 0.558,0.88 0.414,0.244 0.193,0.668 0.467,0.831 0.274,0.163 10 A24 0.128,0.0 2.554,0.355 2.426,0.355 10 *a 0.825,1.435 0.825,1.856 false 0.618,1.89 0.969,2.067 0.351,0.177 10 +BS

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A24-31 (+BS) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid])


Result:
Proceed to
OK
NG



OK

3.INSPECT SKID CONTROL ECU (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SKID CONTROL ECU (GND TERMINAL)
a.

Disconnect the A24 and A25 skid control ECU (master cylinder solenoid) connectors.


b.
C124799E67
0.198,0.615 0.604,0.865 0.406,0.25 0.698,3.74 1.104,3.99 0.406,0.25 0.656,1.406 0.375,2.354 true 0.99,1.635 1.313,2.333 true 1.865,3.948 2.583,3.469 true 0.115,0.063 0.323,0.26 0.208,0.198 10 false *a 0.271,0.635 0.667,0.906 0.396,0.271 10 false A24 0.781,3.76 1.094,3.938 0.313,0.177 10 false A25 0.146,2.365 0.708,2.583 0.563,0.219 10 false GND1 1.094,2.365 1.656,2.583 0.563,0.219 10 false GND2 2.625,3.385 3.188,3.604 0.563,0.219 10 false GND3

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-1 (GND1) - Body ground Always Below 1 Ω
A24-32 (GND2) - Body ground Always Below 1 Ω
A25-4 (GND3) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid])


Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.RECONFIRM DTC
HINT:

These codes are stored when a problem is detected in the master cylinder solenoid.

The ABS solenoid relay is in the master cylinder solenoid.

Therefore, solenoid relay circuit inspection and relay unit inspection cannot be performed. Be sure to check if any DTC is output before replacing the master cylinder solenoid.



b.

Drive the vehicle at a speed of approximately 32 km/h (20 mph) or more for 60 seconds or more.


c.

Check if the same DTCs are output (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

HINT:

Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.



Result:
Result Proceed to
DTC is not output. A
DTC is output. LHD B
RHD C



A

B

C