Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255415 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1202  Master Reservoir Level Malfunction  


DESCRIPTION

The brake fluid level warning switch (brake master cylinder reservoir sub-assembly) sends the appropriate signal to the skid control ECU (master cylinder solenoid) when the brake fluid level drops.

DTC Code DTC Detection Condition Trouble Area
C1202 When either of the following conditions is detected:
1.

The fluid level of the reservoir is LOW for 4 seconds, or 40 seconds after the ignition switch is turned to ON, or for 7 seconds during pump motor operation.

2.

With the ECU terminal IG1 voltage at 9.5 V to 17.0 V, an open in the brake fluid level warning switch circuit continues for 2 seconds or more.


·

Brake fluid level

·

Brake fluid level warning switch (Brake master cylinder reservoir sub-assembly)

·

Harness or connector

·

Skid control ECU (Master cylinder solenoid)



WIRING DIAGRAM

C173284E10
1.365,0.573 2.333,0.813 0.969,0.24 10 false from IG Circuit 3.677,0.76 4.563,1.01 0.885,0.25 10 false ECU-IG No. 2 5.656,0.469 5.906,0.667 0.25,0.198 10 false 46 2.688,1.656 2.917,1.885 0.229,0.229 10 false 1 5.938,0.583 6.26,0.781 0.323,0.198 10 false IG1 5.938,1.792 6.271,1.99 0.333,0.198 10 false LBL 4.146,1.667 4.375,1.896 0.229,0.229 10 false 2 2.875,1.656 3.25,1.865 0.375,0.208 10 false GND 3.802,1.656 4.104,1.854 0.302,0.198 10 false LBL 2.458,2.333 2.792,2.552 0.333,0.219 10 false A26 2.448,2.5 4.521,3.083 2.073,0.583 10 false Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Sub-assembly) 5.5,2.854 5.833,3.073 0.333,0.219 10 false A24 5.469,3.031 7.094,3.469 1.625,0.438 10 false Skid Control ECU (Master Cylinder Solenoid) 5.656,1.656 5.906,1.854 0.25,0.198 10 false 41

CAUTION / NOTICE / HINT

NOTICE:

When replacing the master cylinder solenoid, perform zero point calibration (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


HINT:

When C1241 is output together with C1202, inspect and repair the trouble areas indicated by C1241 first.


PROCEDURE

1.CHECK AND REPAIR BRAKE FLUID LEAKAGE
a.

Turn the ignition switch off.


b.

Depress the brake pedal 20 times or more (until the pedal reaction feels light and pedal stroke becomes longer).


c.

Check the amount of fluid in the brake reservoir.

HINT:

When the ignition switch is turned to ON, brake fluid is sent to the accumulator and the fluid level decreases by approximately 10 mm (0.394 in.) from the level when the ignition switch is off (normal).


OK:

Brake fluid level is normal.



Result:
Proceed to
OK
NG



OK

2.INSPECT BRAKE FLUID LEVEL WARNING SWITCH

NG

CHECK AND REPAIR BRAKE FLUID LEAKAGE

2.INSPECT BRAKE FLUID LEVEL WARNING SWITCH
a.

Disconnect the A26 brake fluid level warning switch (brake master cylinder reservoir sub-assembly) connector.


b.
C217215E01
0.12,0.094 0.297,0.271 0.177,0.177 10 *a 2.531,1.493 2.909,1.655 0.378,0.163 10 GND 0.503,1.499 0.804,1.690 0.302,0.191 10 LBL 1.409,1.251 0.653,1.366 0.653,1.366 0.653,1.46 false 1.974,1.266 2.668,1.374 2.668,1.374 2.668,1.439 false

Measure the resistance according to the value(s) in the table below.

HINT:
·

A float is placed inside the reservoir. Its position can be changed by increasing/decreasing the level of brake fluid.

·

The warning switch is switched on/off at +/-5 mm (+/-0.197 in.) from the MIN level.



Standard Resistance:
Tester Connection Condition Specified Condition
1 (GND) - 2 (LBL) Float UP (Switch off) 1.9 to 2.1 kΩ
1 (GND) - 2 (LBL) Float DOWN (Switch on) Below 1 Ω


Text in Illustration
*a Component without harness connected
(Brake Fluid Level Warning Switch [Brake Master Cylinder Reservoir Sub-assembly])


Result:
Result Proceed to
OK A
NG LHD B
RHD C


HINT:

If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.



A

3.CHECK HARNESS AND CONNECTOR (BRAKE FLUID LEVEL WARNING SWITCH - SKID CONTROL ECU)

B

REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

C

REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (BRAKE FLUID LEVEL WARNING SWITCH - SKID CONTROL ECU)
a.

Disconnect the A24 skid control ECU (master cylinder solenoid) connector and A26 brake fluid level warning switch (brake master cylinder reservoir sub-assembly)connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-41 (LBL) - A26-2 (LBL) Always Below 1 Ω
A24-41 (LBL) - Body ground Always 10 kΩ or higher
A26-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.RECONFIRM DTC

b.

Drive the vehicle at a speed of approximately 32 km/h (20 mph) or more for 60 seconds or more.


c.

Check if the same DTC is output (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

HINT:

Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.



Result:
Result Proceed to
DTC is not output. A
DTC is output. LHD B
RHD C



A

B

REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

C

REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY