Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2014.08–2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255415 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1447  External System Malfunction  


DESCRIPTION

The skid control ECU (master cylinder solenoid) acquires the steering sensor zero point every time the ignition switch is turned ON and the vehicle is driven at 35 km/h (22 mph) or more for approximately 5 seconds. The ECU also stores previous zero points.

DTC Code DTC Detection Condition Trouble Area
C1447 Due to the VGRS system calibration request, the steering sensor zero point value has been cleared..
·

Speed sensor

·

Seering sensor

·

Yaw rate and acceleration sensor (Airbag sensor assembly)

·

VGRS ECU (Steering control ECU)*



*: w/ VGRS System


PROCEDURE

1.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Turn the ignition switch ON again and check that no CAN communication system DTCs are output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).


d.

Start the engine.


e.

Drive the vehicle at a speed of 35 km/h (22 mph) or more and turn the steering wheel to the right and left and check that no speed sensor or yaw rate and acceleration sensor DTCs are output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC C1447 is output. A
CAN communication system DTCs are output. B
Speed sensor, yaw rate and acceleration sensor (airbag sensor assembly) and/or steering sensor DTCs are output. C
DTCs are not output. D

HINT:
·

For the CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING), refer to the following:


·

When CAN communication DTCs are output, inspect and repair the trouble areas indicated by CAN communication first.

·

If a speed sensor or the yaw rate and acceleration sensor is malfunctioning, DTCs for the steering sensor may be stored even though the steering sensor is normal.

·

If speed sensor and yaw rate and acceleration sensor DTCs are output simultaneously, repair these malfunctions and then inspect the steering sensor.

·

If DTC C1447 is not output again, the DTC may have been stored due to a temporary loss of steering sensor zero point calibration, such as a loss of calibration due to the power source voltage being low.





A

2.CHECK STEERING SENSOR ZERO POINT CALIBRATION

B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

C

D

2.CHECK STEERING SENSOR ZERO POINT CALIBRATION
a.

Drive the vehicle straight ahead at 35 km/h (22 mph) or more for at least 5 seconds.


b.

Check that the steering wheel is correctly centered while driving straight ahead.

HINT:

If front wheel alignment and steering are adjusted as a result of an off-center steering wheel, acquire the yaw rate and acceleration sensor zero point again after the adjustments are completed.


OK:

The steering wheel is correctly centered.




OK

3.RECONFIRM DTC

NG

ADJUST FRONT WHEEL ALIGNMENT OR STEERING

3.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 35 km/h (22 mph) or more and turn the steering wheel to the right and left.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC C1447 is output (for LHD) A
DTC C1447 is output (for RHD) B
DTC C1447 is not output C

HINT:

If DTC C1447 is not output again, the DTC may have been stored due to a temporary loss of the steering sensor zero point calibration, such as a loss of calibration due to the power source voltage being low.




A

B

C

END