Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Seat Position Memory System) › from 2015.08
RM2660E _58 Vehicle Interior _052845 SEAT _0255625 FRONT POWER SEAT CONTROL SYSTEM(w/ Seat Position Memory System) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Seat Position Memory System)  One or more Power Seat Motors do not Operate  


DESCRIPTION

When the front power seat switch LH*1, RH*2 is operated, a command signal is sent to the built-in ECU. The built-in ECU then controls the appropriate seat motor as needed. The built-in ECU is designed so that a malfunction of the seat memory system will not interfere with manual seat control.

*1: for LHD

*2: for RHD


WIRING DIAGRAM

B557520E02
2.49,0.49 3.302,0.708 0.813,0.219 10 false P/SEAT F/L 0.833,0.271 1.656,0.5 0.823,0.229 10 false from Battery 0.417,4.656 0.875,4.854 0.458,0.198 10 false c21 0.417,4.865 1.427,5.396 1.01,0.531 10 false Lumbar Support Adjuster Assembly LH 0.594,4.292 0.75,4.49 0.156,0.198 10 false 2 1.219,4.292 1.375,4.49 0.156,0.198 10 false 1 1.75,5.167 2.208,5.365 0.458,0.198 10 false c16 1.75,5.323 2.938,5.698 1.188,0.375 10 false Power Seat Switch Assembly LH 1.51,3.635 1.667,3.833 0.156,0.198 10 false 1 1.521,4.292 1.677,4.49 0.156,0.198 10 false 4 1.75,3.646 1.906,3.844 0.156,0.198 10 false R 1.74,4.292 1.896,4.49 0.156,0.198 10 false H 3.01,3.448 3.167,3.646 0.156,0.198 10 false B 3.271,3.448 3.427,3.646 0.156,0.198 10 false 3 2.948,3.823 3.26,4.021 0.313,0.198 10 false E2 2.958,4.458 3.271,4.656 0.313,0.198 10 false E2 3.271,3.813 3.427,4.01 0.156,0.198 10 false 2 3.271,4.458 3.427,4.656 0.156,0.198 10 false 5 5.917,8.01 7.042,8.385 1.125,0.375 10 false Front Power Seat Switch LH 5.906,7.833 6.365,8.031 0.458,0.198 10 false c39 6.104,7.396 6.563,7.594 0.458,0.198 10 false GND 5.865,7.271 6.021,7.469 0.156,0.198 10 false 1 4.115,4.521 5.646,4.865 1.531,0.344 10 false Front Seat with Adjuster Frame Assembly LH 4.573,6.104 5.323,6.323 0.75,0.219 10 false Slide Motor 4.156,6.563 4.615,6.76 0.458,0.198 10 false c17 4.156,6.729 5.625,7.104 1.469,0.375 10 false Power Seat Slide Motor Assembly LH 5.156,5.802 5.313,6 0.156,0.198 10 false 1 4.563,5.802 4.719,6 0.156,0.198 10 false 2 6.104,5.906 6.719,6.104 0.615,0.198 10 false SLD+ 5.865,5.802 6.021,6 0.156,0.198 10 false 2 6.104,5.5 6.719,5.698 0.615,0.198 10 false SLD- 5.875,5.385 6.031,5.583 0.156,0.198 10 false 4 4.563,0.938 4.719,1.135 0.156,0.198 10 false 1 5.167,0.938 5.323,1.135 0.156,0.198 10 false 2 4.406,1.219 4.865,1.417 0.458,0.198 10 false c20 4.385,1.375 5.406,1.583 1.021,0.208 10 false Reclining Motor 6.094,1.042 6.708,1.24 0.615,0.198 10 false RCL+ 5.885,0.938 6.042,1.135 0.156,0.198 10 false 9 5.813,0.521 6.125,0.719 0.313,0.198 10 false 12 6.094,0.635 6.708,0.833 0.615,0.198 10 false RCL- 4.542,2.49 5,2.688 0.458,0.198 10 false c18 4.531,2.656 5.333,2.896 0.802,0.24 10 false Lifter Motor 4.563,2.198 4.719,2.396 0.156,0.198 10 false 1 5.167,2.208 5.323,2.406 0.156,0.198 10 false 2 5.885,2.229 6.042,2.427 0.156,0.198 10 false 8 6.104,2.302 6.719,2.5 0.615,0.198 10 false LFT+ 6.104,1.896 6.719,2.094 0.615,0.198 10 false LFT- 5.823,1.781 6.135,1.979 0.313,0.198 10 false 11 4.281,3.688 4.74,3.885 0.458,0.198 10 false c19 4.281,3.844 5.583,4.042 1.302,0.198 10 false Front Vertical Motor 4.563,3.417 4.719,3.615 0.156,0.198 10 false 2 5.156,3.417 5.313,3.615 0.156,0.198 10 false 1 5.885,3 6.042,3.198 0.156,0.198 10 false 5 5.896,3.417 6.052,3.615 0.156,0.198 10 false 7 6.104,3.521 6.531,3.708 0.427,0.188 10 false FRV+ 6.104,3.104 6.531,3.292 0.427,0.188 10 false FRV- 5.885,0.177 6.042,0.375 0.156,0.198 10 false 6 6.094,0.281 6.406,0.479 0.313,0.198 10 false +B 0.063,0.052 0.76,0.302 0.698,0.25 12 false for LHD:

B557520E05
2.49,0.49 3.302,0.708 0.813,0.219 10 false P/SEAT F/R 0.833,0.271 1.656,0.5 0.823,0.229 10 false from Battery 0.417,4.656 0.875,4.854 0.458,0.198 10 false c29 0.417,4.865 1.427,5.396 1.01,0.531 10 false Lumbar Support Adjuster Assembly RH 1.219,4.292 1.375,4.49 0.156,0.198 10 false 2 0.594,4.292 0.75,4.49 0.156,0.198 10 false 1 1.75,5.167 2.208,5.365 0.458,0.198 10 false c28 1.75,5.323 2.938,5.698 1.188,0.375 10 false Power Seat Switch Assembly RH 1.51,3.635 1.667,3.833 0.156,0.198 10 false 1 1.521,4.292 1.677,4.49 0.156,0.198 10 false 4 1.75,3.646 1.906,3.844 0.156,0.198 10 false R 1.74,4.292 1.896,4.49 0.156,0.198 10 false H 3.01,3.448 3.167,3.646 0.156,0.198 10 false B 3.271,3.448 3.427,3.646 0.156,0.198 10 false 3 3.01,3.823 3.323,4.021 0.313,0.198 10 false E 3.021,4.458 3.333,4.656 0.313,0.198 10 false E 3.271,3.813 3.427,4.01 0.156,0.198 10 false 2 3.271,4.458 3.427,4.656 0.156,0.198 10 false 5 5.917,8.01 7.042,8.385 1.125,0.375 10 false Front Power Seat Switch RH 5.906,7.833 6.365,8.031 0.458,0.198 10 false c46 6.104,7.396 6.563,7.594 0.458,0.198 10 false GND 5.865,7.271 6.021,7.469 0.156,0.198 10 false 1 4.115,4.521 5.646,4.865 1.531,0.344 10 false Front Seat with Adjuster Frame Assembly RH 4.573,6.104 5.323,6.323 0.75,0.219 10 false Slide Motor 4.156,6.563 4.615,6.76 0.458,0.198 10 false c3 4.156,6.729 5.625,7.104 1.469,0.375 10 false Power Seat Slide Motor Assembly RH 4.552,5.802 4.708,6 0.156,0.198 10 false 1 5.156,5.802 5.313,6 0.156,0.198 10 false 2 6.104,5.906 6.719,6.104 0.615,0.198 10 false SLDF 5.865,5.802 6.021,6 0.156,0.198 10 false 2 6.104,5.5 6.719,5.698 0.615,0.198 10 false SLDR 5.875,5.385 6.031,5.583 0.156,0.198 10 false 4 4.563,0.938 4.719,1.135 0.156,0.198 10 false 1 5.167,0.938 5.323,1.135 0.156,0.198 10 false 2 4.406,1.219 4.865,1.417 0.458,0.198 10 false c6 4.385,1.375 5.406,1.583 1.021,0.208 10 false Reclining Motor 6.094,1.042 6.708,1.24 0.615,0.198 10 false RCLF 5.885,0.938 6.042,1.135 0.156,0.198 10 false 9 5.813,0.521 6.125,0.719 0.313,0.198 10 false 12 6.094,0.635 6.708,0.833 0.615,0.198 10 false RCLR 4.542,2.49 5,2.688 0.458,0.198 10 false c4 4.531,2.656 5.333,2.896 0.802,0.24 10 false Lifter Motor 5.156,2.198 5.313,2.396 0.156,0.198 10 false 1 4.542,2.198 4.698,2.396 0.156,0.198 10 false 2 5.885,2.229 6.042,2.427 0.156,0.198 10 false 8 6.104,2.302 6.719,2.5 0.615,0.198 10 false LUP 6.104,1.896 6.719,2.094 0.615,0.198 10 false LDWN 5.823,1.781 6.135,1.979 0.313,0.198 10 false 11 4.281,3.688 4.74,3.885 0.458,0.198 10 false c5 4.281,3.844 5.583,4.042 1.302,0.198 10 false Front Vertical Motor 5.156,3.417 5.313,3.615 0.156,0.198 10 false 2 4.563,3.417 4.719,3.615 0.156,0.198 10 false 1 5.885,3 6.042,3.198 0.156,0.198 10 false 5 5.896,3.417 6.052,3.615 0.156,0.198 10 false 7 6.104,3.521 6.531,3.708 0.427,0.188 10 false FUP 6.104,3.104 6.677,3.313 0.573,0.208 10 false FDWN 5.885,0.177 6.042,0.375 0.156,0.198 10 false 6 6.094,0.281 6.521,0.479 0.427,0.198 10 false +B2 0.063,0.052 0.76,0.302 0.698,0.25 12 false for RHD:

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK FRONT POWER SEAT OPERATION
a.

Check that each function of the power seat operates normally by using the front power seat switches (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Seat Position Memory System)>OPERATION CHECK).

Result
Result Proceed to
All front power seat switch operations are malfunctioning except lumbar support switch operation A
Only lumbar support switch operation is malfunctioning B



A

2.READ VALUE USING GTS (FRONT POWER SEAT SWITCH)

B

6.INSPECT POWER SEAT SWITCH ASSEMBLY
2.READ VALUE USING GTS (FRONT POWER SEAT SWITCH)
a.

Using the GTS, read the Data List.

Driver Seat
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Reclining Rear Reclining switch signal (Rearward) / ON or OFF ON: Reclining switch (Rearward) on
OFF: Reclining switch (Rearward) off
-
Reclining Front Reclining switch signal (Forward) / ON or OFF ON: Reclining switch (Forward) on
OFF: Reclining switch (Forward) off
-
Front Vertical Down Front vertical switch signal (Downward) / ON or OFF ON: Front vertical switch (Downward) on
OFF: Front vertical switch (Downward) off
-
Front Vertical Up Front vertical switch signal (Upward) / ON or OFF ON: Front vertical switch (Upward) on
OFF: Front vertical switch (Upward) off
-
Lifter Switch Down Lifter switch signal (Downward) / ON or OFF ON: Lifter switch (Downward) on
OFF: Lifter switch (Downward) off
-
Lifter Switch Up Lifter switch signal (Upward) / ON or OFF ON: Lifter switch (Upward) on
OFF: Lifter switch (Upward) off
-
Slide Rear Sliding switch signal (Rearward) / ON or OFF ON: Sliding switch (Rearward) on
OFF: Sliding switch (Rearward) off
-
Slide Front Sliding switch signal (Forward) / ON or OFF ON: Sliding switch (Forward) on
OFF: Sliding switch (Forward) off
-

OK:

On the GTS screen, each item changes between ON and OFF according to above chart.



Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C


A

3.PERFORM ACTIVE TEST USING GTS (FRONT POWER SEAT MOTOR)

B

REPLACE FRONT POWER SEAT SWITCH LH

C

REPLACE FRONT POWER SEAT SWITCH RH

3.PERFORM ACTIVE TEST USING GTS (FRONT POWER SEAT MOTOR)
a.

Using the GTS, perform the Active Test.

Driver Seat
Tester Display Test Part Control Range Diagnostic Note
Seat Reclining Seat reclining operation OFF/Rear/Front -
Front Vertical Operation Seat front vertical operation OFF/Down/Up -
Lifter Operation Seat lifter operation OFF/Down/Up -
Seat Slide Operation Seat sliding operation OFF/Rear/Front -

OK:

The power seat motors operate normally.


Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG (except slide motor) C
NG (slide motor) D



A

REPLACE FRONT POWER SEAT SWITCH LH

B

REPLACE FRONT POWER SEAT SWITCH RH

C

4.INSPECT FRONT SEAT WITH ADJUSTER FRAME ASSEMBLY (FRONT POWER SEAT MOTOR)

D

9.INSPECT POWER SEAT SLIDE MOTOR ASSEMBLY (SLIDE MOTOR)
4.INSPECT FRONT SEAT WITH ADJUSTER FRAME ASSEMBLY (FRONT POWER SEAT MOTOR)
a.

Remove the front seat with adjuster frame assembly LH*1, RH*2 (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY).

*1: for LHD

*2: for RHD


b.
B188327E03
0.13,0.054 2.666,0.460 2.536,0.406 10 Component without harness connected: (Front Vertical Motor)

Check operation of the front vertical motor.

i.

Check if the seat moves smoothly when the battery is connected to the front vertical motor connector terminals.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 1
Battery negative (-) → 2
Upward
Battery positive (+) → 2
Battery negative (-) → 1
Downward




c.
B188327E04
0.13,0.054 2.666,0.460 2.536,0.406 10 Component without harness connected: (Lifter Motor)

Check operation of the lifter motor.

i.

Check if the seat moves smoothly when the battery is connected to the lifter motor connector terminals.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 2
Battery negative (-) → 1
Upward
Battery positive (+) → 1
Battery negative (-) → 2
Downward




d.
B188327E05
0.13,0.054 2.666,0.460 2.536,0.406 10 Component without harness connected: (Reclining Motor)

Check operation of the reclining motor.

i.

Check if the seat moves smoothly when the battery is connected to the reclining motor connector terminals.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 2
Battery negative (-) → 1
Forward
Battery positive (+) → 1
Battery negative (-) → 2
Rearward




Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C


A

5.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - POWER SEAT MOTOR)

B

REPLACE FRONT SEAT WITH ADJUSTER FRAME ASSEMBLY LH

C

REPLACE FRONT SEAT WITH ADJUSTER FRAME ASSEMBLY RH

5.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - POWER SEAT MOTOR)

*1: for LHD

*2: for RHD

a.

Disconnect the c39*1, c46*2 switch connector.


b.

Disconnect the c18*1, c4*2, c19*1, c5*2 and c20*1, c6*2 motor connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
c39-5 (FRV-) - c19-2 Always Below 1 Ω
c39-7 (FRV+) - c19-1 Always Below 1 Ω
c39-11 (LFT-) - c18-1 Always Below 1 Ω
c39-8 (LFT+) - c18-2 Always Below 1 Ω
c39-12 (RCL-) - c20-1 Always Below 1 Ω
c39-9 (RCL+) - c20-2 Always Below 1 Ω
c39-1 (GND) - Body ground Always Below 1 Ω
c39-5 (FRV-) or c19-2 - Body ground Always 10 kΩ or higher
c39-7 (FRV+) or c19-1 - Body ground Always 10 kΩ or higher
c39-11 (LFT-) or c18-1 - Body ground Always 10 kΩ or higher
c39-8 (LFT+) or c18-2 - Body ground Always 10 kΩ or higher
c39-12 (RCL-) or c20-1 - Body ground Always 10 kΩ or higher
c39-9 (RCL+) or c20-2 - Body ground Always 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition
c46-5 (FDWN) - c5-2 Always Below 1 Ω
c46-7 (FUP) - c5-1 Always Below 1 Ω
c46-11 (LDWN) - c4-1 Always Below 1 Ω
c46-8 (LUP) - c4-2 Always Below 1 Ω
c46-12 (RCLR) - c6-1 Always Below 1 Ω
c46-9 (RCLF) - c6-2 Always Below 1 Ω
c46-1 (GND) - Body ground Always Below 1 Ω
c46-5 (FDWN) or c5-2 - Body ground Always 10 kΩ or higher
c46-7 (FUP) or c5-1 - Body ground Always 10 kΩ or higher
c46-11 (LDWN) or c4-1 - Body ground Always 10 kΩ or higher
c46-8 (LUP) or c4-2 - Body ground Always 10 kΩ or higher
c46-12 (RCLR) or c6-1 - Body ground Always 10 kΩ or higher
c46-9 (RCLF) or c6-2 - Body ground Always 10 kΩ or higher



Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C


A

REPLACE FRONT POWER SEAT SWITCH LH

B

REPLACE FRONT POWER SEAT SWITCH RH

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT POWER SEAT SWITCH ASSEMBLY

*1: for LHD

*2: for RHD

a.

Remove the power seat switch assembly LH*1, RH*2 (See page Vehicle Interior>SEAT>POWER SEAT SWITCH (w/o Seat Position Memory System)>REMOVAL).


b.

Inspect the power seat switch assembly LH*1, RH*2 (See page Vehicle Interior>SEAT>POWER SEAT SWITCH (w/o Seat Position Memory System)>INSPECTION).


Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C


A

7.INSPECT LUMBAR SUPPORT ADJUSTER ASSEMBLY

B

C

7.INSPECT LUMBAR SUPPORT ADJUSTER ASSEMBLY

*1: for LHD

*2: for RHD

a.

Remove the lumbar support adjuster assembly LH*1, RH*2 (See page Vehicle Interior>SEAT>LUMBAR SUPPORT ADJUSTER ASSEMBLY (for Power Seat)>REMOVAL).


b.

Inspect the lumbar support adjuster assembly LH*1, RH*2 (See page Vehicle Interior>SEAT>LUMBAR SUPPORT ADJUSTER ASSEMBLY (for Power Seat)>INSPECTION).


Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C


A

8.CHECK HARNESS AND CONNECTOR (POWER SEAT SWITCH ASSEMBLY - BATTERY AND BODY GROUND)

B

REPLACE LUMBAR SUPPORT ADJUSTER ASSEMBLY LH

C

REPLACE LUMBAR SUPPORT ADJUSTER ASSEMBLY RH

8.CHECK HARNESS AND CONNECTOR (POWER SEAT SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
a.
U163949E04
2.156,2.146 2.521,2.625 true 1.458,2.156 1.365,2.74 true 1.76,2.167 2,2.677 true 0.073,0.063 2.458,0.531 2.385,0.469 10 false Front view of wire harness connector: (to Power Seat Switch Assembly) 1.198,2.74 1.594,2.917 0.396,0.177 10 false E2*1 2.01,2.698 2.156,2.865 0.146,0.167 10 false B 2.427,2.646 2.823,2.865 0.396,0.219 10 false E2*1 0.198,1.479 0.563,1.677 0.365,0.198 10 false c16 0.219,2.01 0.583,2.208 0.365,0.198 10 false c28 0.073,2.604 0.927,2.927 0.854,0.323 10 false *1: for LHD 0.083,2.938 0.865,3.281 0.781,0.344 10 false *2: for RHD 0.635,1.458 0.917,1.667 0.281,0.208 10 false *1 0.635,2.021 0.917,2.229 0.281,0.208 10 false *2 1.198,2.917 1.594,3.094 0.396,0.177 10 false E*2 2.427,2.813 2.823,3.031 0.396,0.219 10 false E*2

Disconnect the c16*1, c28*2 switch connector.

*1: for LHD

*2: for RHD


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD:
Tester Connection Condition Specified Condition
c16-3 (B) - Body ground Always 11 to 14 V

for RHD:
Tester Connection Condition Specified Condition
c28-3 (B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
c16-5 (E2) - Body ground Always Below 1 Ω
c16-2 (E2) - Body ground

for RHD:
Tester Connection Condition Specified Condition
c28-5 (E) - Body ground Always Below 1 Ω
c28-2 (E) - Body ground



Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C


A

REPLACE POWER SEAT SWITCH ASSEMBLY LH

B

REPLACE POWER SEAT SWITCH ASSEMBLY RH

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT POWER SEAT SLIDE MOTOR ASSEMBLY (SLIDE MOTOR)
a.

Remove the power seat motor assembly LH*1, RH*2 (slide motor) (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY).

*1: for LHD

*2: for RHD


b.
B188327E01
0.13,0.054 2.666,0.460 2.536,0.406 10 Component without harness connected: (Slide Motor)

Check operation of the slide motor.

i.

Check if the seat moves smoothly when the battery is connected to the slide motor connector terminals.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 1
Battery negative (-) → 2
Forward
Battery positive (+) → 2
Battery negative (-) → 1
Rearward




Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C


A

10.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - SLIDE MOTOR)

B

REPLACE POWER SEAT SLIDE MOTOR ASSEMBLY LH (SLIDE MOTOR)

C

REPLACE POWER SEAT SLIDE MOTOR ASSEMBLY RH (SLIDE MOTOR)

10.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - SLIDE MOTOR)

*1: for LHD

*2: for RHD

a.

Disconnect the c39*1, c46*2 switch connector.


b.

Disconnect the c17*1, c3*2 motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
c39-4 (SLD-) - c17-2 Always Below 1 Ω
c39-2 (SLD+) - c17-1 Always Below 1 Ω
c39-1 (GND) - Body ground Always Below 1 Ω
c39-4 (SLD-) or c17-2 - Body ground Always 10 kΩ or higher
c39-2 (SLD+) or c17-1 - Body ground Always 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition
c46-4 (SLDR) - c3-2 Always Below 1 Ω
c46-2 (SLDF) - c3-1 Always Below 1 Ω
c46-1 (GND) - Body ground Always Below 1 Ω
c46-4 (SLDR) or c3-2 - Body ground Always 10 kΩ or higher
c46-2 (SLDF) or c3-1 - Body ground Always 10 kΩ or higher



Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C


A

REPLACE FRONT POWER SEAT SWITCH LH

B

REPLACE FRONT POWER SEAT SWITCH RH

C

REPAIR OR REPLACE HARNESS OR CONNECTOR