Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (for RHD) › 2021.04–2021.07
RM38G0E _54 Brake _100463 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0467251 BRAKE ACTUATOR(for RHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for RHD)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C455219N05
1.042,4.333 1.781,4.625 0.74,0.292 1.073,4.385 1.74,4.583 0.667,0.198 1.104,0.99 2.094,1.208 0.99,0.219 1.052,0.938 2.135,1.25 1.083,0.313 1.74,3.927 2.417,3.927 false 2,3.083 2,2.719 2,2.719 2.365,2.719 false 5.438,1.896 5.771,1.896 false 3.823,3.615 4.156,3.615 false 1.771,3.094 2.438,3.094 false 2,2.917 3,2.917 true 2.031,3.927 2.031,3.563 2.031,3.563 2.396,3.563 false 2.031,3.75 3.031,3.75 true 3.031,0.938 3.281,0.76 3.281,0.76 3.417,0.76 false 2.854,2.354 3.25,2.135 3.25,2.135 3.385,2.135 false 1.75,4.5 2.417,4.5 false 2.021,4.5 2.021,4.25 2.021,4.25 2.385,4.25 false 1.531,0.979 1.531,0.479 false 2.021,4.344 3.021,4.344 false 6.229,1.75 6.896,2.25 0.667,0.5 18 false 3 1.51,3.781 2.177,4.281 0.667,0.5 18 false 2 1.51,2.948 2.177,3.448 0.667,0.5 18 false 1 4.208,3.521 4.625,3.771 0.417,0.25 10 false *1 4.688,1.531 5.104,1.781 0.417,0.25 10 false *2 3.458,2.063 3.875,2.313 0.417,0.25 10 false *3 1.719,0.375 2.135,0.625 0.417,0.25 10 false x 3 3.5,0.688 3.917,0.938 0.417,0.25 10 false *2 1.104,4.396 2.302,4.583 1.198,0.188 8 false 19 (194, 14) 1.156,1.021 2.573,1.292 1.417,0.271 8 false 6.5 (66, 58 in.*lbf)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 BRAKE ACTUATOR BRACKET CUSHION 44547B (Click here) - -
2 NO. 1 BRAKE ACTUATOR CASE COLLAR 44521A (Click here) - -
3 BRAKE ACTUATOR ASSEMBLY 44510 (Click here) - -

*1 BRAKE ACTUATOR BRACKET ASSEMBLY *2 NO. 1 BRAKE ACTUATOR BRACKET
*3 NO. 2 BRAKE ACTUATOR BRACKET - -
V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) - -

C457194N04
4.938,4.271 5.708,4.604 0.771,0.333 4.969,4.333 5.667,4.552 0.698,0.219 2.198,0.375 2.99,0.719 0.792,0.344 2.156,0.313 3.031,0.76 0.875,0.448 1.177,0.271 2.042,0.615 0.865,0.344 1.135,0.208 2.083,0.656 0.948,0.448 1.927,2.375 2.635,2.604 0.708,0.229 1.885,2.323 2.677,2.646 0.792,0.323 0.667,1.635 1.469,2.01 0.802,0.375 0.625,1.583 1.51,2.063 0.885,0.479 3.656,0.792 3.573,0.542 3.573,0.542 2.99,0.542 true 3.385,0.552 3.469,0.802 true 3.281,0.552 3.375,0.833 true 3.5,0.552 3.583,0.802 true 0.781,0.458 0.781,0.729 true 3.833,0.5 3.927,0.24 3.927,0.24 4.094,0.24 false 4.323,4.01 4.802,4.438 4.802,4.438 4.969,4.438 false 3.896,2.469 4.333,2.99 4.333,2.99 4.5,2.99 false 1.177,0.458 0.5,0.458 0.5,0.458 0.5,0.792 true 4.75,1.177 5.417,2.052 5.417,2.052 5.583,2.052 true 2.635,2.49 2.802,2.49 2.802,2.49 3.094,1.802 true 6.542,0.219 6.875,0.219 false 6.552,0.583 6.885,0.583 false 6.583,1 6.875,1 false 6.521,1.448 6.854,1.448 false 3.229,3.802 3.469,4.115 3.469,4.115 3.552,4.115 false 1.479,1.833 1.896,1.833 1.896,1.833 1.896,1.417 true 1.719,1.396 1.719,1.833 true 0.604,3.135 0.771,3.135 0.771,3.135 1.125,3.729 true 3.865,3.979 4.198,4.396 0.333,0.417 18 false 4 4.427,3.917 4.677,4.167 0.25,0.25 10 false x 2 3.24,1.719 3.49,1.969 0.25,0.25 10 false x3 2.229,0.396 3.229,0.563 1,0.167 8 false 15.2 (155, 11) 2.229,0.542 3.25,0.844 1.021,0.302 8 false 13.4 (137, 10)* 1.208,0.302 2.125,0.573 0.917,0.271 8 false 19.5 (199, 14) 1.208,0.438 2.073,0.708 0.865,0.271 8 false 17.4 (177, 13)* 4.823,2.875 5.156,3.292 0.333,0.417 18 false 5 4.531,0.115 5.198,0.448 0.667,0.333 18 false 7 1.469,0.667 1.948,1.229 0.479,0.563 18 false 6, 8 4.385,0.177 5.052,0.51 0.667,0.333 10 false ● 0.24,2.99 0.906,3.323 0.667,0.333 18 false 15 5.917,1.948 6.25,2.365 0.333,0.417 18 false 9 5.76,0.438 6.594,0.833 0.833,0.396 18 false 10, 14 2.667,0.792 3,1.208 0.333,0.417 18 false 6 1.979,2.406 2.906,2.792 0.927,0.385 8 false 19 (194, 14) 0.917,2.073 1.396,2.635 0.479,0.563 18 false 6 6.188,1.302 6.521,1.719 0.333,0.417 18 false 11 4.948,0.833 6.573,1.333 1.625,0.5 18 false 12, 13, 16, 18 6.177,0.052 6.51,0.469 0.333,0.417 18 false 17 0.688,1.667 1.604,1.938 0.917,0.271 8 false 19.5 (199, 14) 0.688,1.813 1.552,2.083 0.865,0.271 8 false 17.4 (177, 13)* 4.99,4.365 5.917,4.75 0.927,0.385 8 false 19 (194, 14)

Procedure Part Name Code
Z101186

Z101188

Z101187

4 NO. 3 BRAKE ACTUATOR BRACKET 44593 (Click here) - -
5 BRAKE ACTUATOR WITH BRACKET - (Click here) - -
6 CONNECT BRAKE TUBE - (Click here) - -
7 NO. 2 BRAKE TUBE CLAMP 47372 - - -
8 INSTALL BRAKE TUBE - (Click here) - -
9 ENGINE ROOM MAIN WIRE 82111 (Click here) - -
10 FILL RESERVOIR WITH BRAKE FLUID - - (Click here) -
11 CONNECT CABLE TO NEGATIVE BATTERY TERMINAL - (Click here) - -
12 ECU CONFIGURATION - - -
13 UPDATE ECU SECURITY KEY - - - (Click here)
14 BLEED BRAKE SYSTEM - - (Click here) -
15 ENGINE SIDE COVER RH 51473C - - -
16 PERFORM INITIALIZATION AND CALIBRATION - - - (Click here)
17 CHECK AND CLEAR DTC - - - -
18 INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL - - - (Click here)

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) * For use with a union nut wrench
● Non-reusable part - -

NOTICE:
·

After replacing the brake actuator assembly, make sure to perform ECU configuration.

·

After performing the ECU configuration procedure and update ECU security key procedure, make sure to perform the initialization procedure for when the cable has been disconnected and reconnected to the negative (-) battery terminal.



HINT:

The parking brake indicator light (red) blinks when the ignition switch is turned to ON after replacing the brake actuator assembly. Operate the electric parking brake switch assembly to turn off the parking brake indicator light.


PROCEDURE

Hide 44547B 1.INSTALL BRAKE ACTUATOR BRACKET CUSHION

Z101186

HINT:

Perform this procedure only when replacement of the brake actuator bracket cushions is necessary.



Hide 44521A 2.INSTALL NO. 1 BRAKE ACTUATOR CASE COLLAR

Z101186

NOTICE:

Make sure that the No. 1 brake actuator case collar is in full contact with the brake actuator bracket cushion.


HINT:

Perform this procedure only when replacement of the No. 1 brake actuator case collars is necessary.



Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

Hide 44510 3.INSTALL BRAKE ACTUATOR ASSEMBLY

Z101186

NOTICE:
·

Do not remove the hole plugs of a new brake actuator assembly before connecting the brake tubes because the brake actuator assembly is filled with brake fluid.

·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator assembly when carrying it.




a.
C457225N02
3.354,1.25 3.458,1.427 0.104,0.177 10 true 1 2.302,1.24 2.458,1.417 0.156,0.177 10 true 2 4.823,2.406 4.958,2.594 0.135,0.188 10 true 3 0.406,0.094 1.083,0.708 0.677,0.615 18 false i, ii

i.

Temporarily install the brake actuator assembly to the brake actuator bracket assembly with the 3 bolts.


ii.

Install the brake actuator assembly to the brake actuator bracket assembly with the 3 bolts in the order shown in the illustration.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)



Hide 44593 4.INSTALL NO. 3 BRAKE ACTUATOR BRACKET

Z101186

HINT:

Perform this procedure only when replacement of the No. 3 brake actuator bracket is necessary.



a.
C457169N03
4.26,0.271 4.417,0.469 0.156,0.198 10 true 1 2.677,0.573 2.833,0.771 0.156,0.198 10 true 2 0.354,0.042 1,0.646 0.646,0.604 18 true i, ii

i.

Temporarily install the No. 3 brake actuator bracket to the body with the 2 bolts.


ii.

Tighten the 2 bolts in the order shown in the illustration.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)



Hide 5.INSTALL BRAKE ACTUATOR WITH BRACKET

Z101186

NOTICE:
·

Do not kink or damage the brake tubes.

·

Do not allow any foreign matter such as dirt or dust to enter the brake tubes from the connecting parts.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not hold the brake actuator with bracket by the connector.

·

Do not drop the brake actuator with bracket when carrying it.




a.
C457171N03
0.365,0.083 1.281,0.667 0.917,0.583 18 false i, ii 4.115,1.604 4.26,1.781 0.146,0.177 10 true 1 2.792,1.5 2.917,1.688 0.125,0.188 10 true 2 4.26,0 4.385,0.188 0.125,0.188 10 true 3

i.

Temporarily install the brake actuator with bracket to the body with the 3 nuts.


ii.

Tighten the 3 nuts in the order shown in the illustration.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)



Hide 6.CONNECT BRAKE TUBE

Z101186

NOTICE:
·

Do not kink or damage the brake tubes.

·

Do not allow any foreign matter such as dirt or dust to enter the brake tube from the connecting parts.




a.
C455221C04
3.792,0.625 4.271,0.344 4.271,0.344 4.438,0.344 true 3.323,0.5 3.073,0.333 3.073,0.333 2.656,0.333 true 2.813,1.042 2.563,1.125 2.563,1.125 2.146,1.125 true 3.094,1.385 2.844,1.573 2.844,1.573 2.51,1.573 true 4.125,1.094 3.792,1.094 3.792,1.094 3.708,0.927 true 3.563,0.521 3.969,0.146 3.969,0.146 4.135,0.146 true 1.938,1.031 2.146,1.198 0.208,0.167 10 false *a 2.25,1.479 2.479,1.656 0.229,0.177 10 true *b 2.427,0.229 2.656,0.406 0.229,0.177 10 true *c 4.135,0.063 4.365,0.229 0.229,0.167 10 true *d 4.469,0.271 4.698,0.458 0.229,0.188 10 true *e 4.156,1.021 4.406,1.188 0.25,0.167 10 true *f 0.396,0.083 0.729,0.5 0.333,0.417 18 false i
*a From 1st Chamber of Brake Booster with Master Cylinder Assembly *b From 2nd Chamber of Brake Booster with Master Cylinder Assembly
*c To Front Wheel Cylinder Assembly RH *d To Front Wheel Cylinder Assembly LH
*e To Rear Wheel Cylinder Assembly RH *f To Rear Wheel Cylinder Assembly LH


i.

Temporarily tighten the 6 brake tubes to the correct position on the brake actuator assembly as shown in the illustration.



b.
C455227C02
4.5,2.417 4.417,2.417 4.417,2.417 4.417,2.167 false 3.594,2.406 3.844,2.656 0.25,0.25 10 false *a 4.552,2.365 4.885,2.615 0.333,0.25 10 false *b 0.458,0.135 1.833,0.49 1.375,0.354 18 false i 3.906,1.083 4.042,1.25 0.135,0.167 10 true A 3.479,0.979 3.594,1.135 0.115,0.156 10 true A 3.177,0.229 3.292,0.385 0.115,0.156 10 true A 3.104,0.573 3.208,0.719 0.104,0.146 10 true A 3.01,0.969 3.125,1.125 0.115,0.156 10 true B 2.76,0.583 2.875,0.74 0.115,0.156 10 true B
*a Torque Wrench Fulcrum Length *b Union Nut Wrench


i.

Using a union nut wrench, fully tighten the 4 brake tubes.

Torque:
Specified tightening torque (A) : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)
Specified tightening torque (B) : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)) (A):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)) (B):

17.4 N*m (177 kgf*cm, 13 ft.*lbf)





Hide 47372 7.INSTALL NO. 2 BRAKE TUBE CLAMP

Z101186

NOTICE:

Do not kink or damage the brake tubes.



a.
C457177C03
4.677,0.354 4.76,0.354 4.76,0.354 5.115,0.458 true 5.292,0.75 5.667,0.583 5.667,0.583 5.76,0.583 true 4.688,0.875 4.771,0.875 4.771,0.875 5.125,0.979 true 5.281,1.24 5.656,1.073 5.656,1.073 5.75,1.073 true 5.281,1.729 5.656,1.563 5.656,1.563 5.75,1.563 true 4.688,1.375 4.771,1.375 4.771,1.375 5.125,1.479 true 4.792,2.031 4.875,2.031 4.875,2.031 5.146,2.26 true 4.479,0.25 4.792,0.406 0.313,0.156 10 false *a 5.813,0.49 6.125,0.646 0.313,0.156 10 false *b 4.49,0.76 4.802,0.917 0.313,0.156 10 false *c 5.802,0.979 6.115,1.135 0.313,0.156 10 false *d 4.479,1.26 4.792,1.417 0.313,0.156 10 false *e 5.802,1.479 6.115,1.635 0.313,0.156 10 false *f 0.417,0.083 0.865,0.583 0.448,0.5 18 false i 4.583,1.927 4.875,2.146 0.292,0.219 10 false *1
*1 No. 2 Brake Tube Clamp - -
*a From 1st Chamber of Brake Booster with Master Cylinder Assembly *b From 2nd Chamber of Brake Booster with Master Cylinder Assembly
*c To Front Wheel Cylinder Assembly RH *d To Front Wheel Cylinder Assembly LH
*e To Rear Wheel Cylinder Assembly RH *f To Rear Wheel Cylinder Assembly LH
V100143

Paint Mark - -


i.

Engage the 6 clamps to install a new No. 2 brake tube clamp so that it is at the center of the paint mark as shown in the illustration.



Hide 8.INSTALL BRAKE TUBE

Z101186

NOTICE:
·

Do not kink or damage the brake tubes.

·

Do not allow any foreign matter such as dirt or dust to enter the brake tube from the connecting parts.




a.
C457208C03
6,1.25 6,0.917 false 5.26,1.198 5.573,1.354 0.313,0.156 10 false *a 5.938,1.281 6.25,1.438 0.313,0.156 10 false *b 0.375,0.031 0.979,0.542 0.604,0.51 18 false i, ii
*a Torque Wrench Fulcrum Length *b Union Nut Wrench


i.

Temporarily tighten the 2 brake tubes.


ii.

Using a union nut wrench, fully tighten the 2 brake tubes.

Torque:
Specified tightening torque : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.378 in.)):

17.4 N*m (177 kgf*cm, 13 ft.*lbf)





Hide 82111 9.CONNECT ENGINE ROOM MAIN WIRE

Z101186

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the actuator connector can be connected smoothly.

·

Do not allow water, oil or dirt to enter the connector.




Hide 10.FILL RESERVOIR WITH BRAKE FLUID

Hide 11.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 14.BLEED BRAKE SYSTEM

Hide 51473C 15.INSTALL ENGINE SIDE COVER RH

Hide 17. CHECK AND CLEAR DTC

Hide 18. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART