Home › Drivetrain › AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE) › PARK / NEUTRAL POSITION SWITCH › 2021.04–2021.07
RM38G0E _52 Drivetrain _100435 AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE _0467302 PARK / NEUTRAL POSITION SWITCH A

AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE  PARK / NEUTRAL POSITION SWITCH  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C456974N01
5.073,3.448 5.823,3.698 0.75,0.25 5.021,3.396 5.875,3.75 0.854,0.354 0.177,1.802 1.177,2.063 1,0.26 1.208,3.448 2.042,3.698 0.833,0.25 0.667,1.083 1.333,1.333 0.667,0.25 0.125,1.75 1.229,2.115 1.104,0.365 1.896,0.76 2.448,0.406 2.448,0.406 2.615,0.406 false 1.042,2.417 1.292,2.417 1.292,2.417 1.792,3.167 false 4.833,3.583 3.833,3.583 3.833,3.583 3.833,3.125 false 2.792,2.063 2.969,2.063 2.969,2.063 3.354,2.698 true 1.177,1.938 1.427,1.938 1.427,1.938 2.969,3.094 false 1.219,2.229 1.469,2.229 1.469,2.229 1.844,2.594 false 1.333,1.208 1.583,1.208 false 2.948,3.583 2.865,3.583 2.865,3.583 2.708,3.333 false 2.052,3.583 2.302,3.583 false 2.313,1.927 2.802,2.271 0.49,0.344 18 false 1, 2 1.75,1.177 2.208,1.375 0.458,0.198 10 false x 2 0.844,2.229 1.125,2.583 0.281,0.354 18 false 3 5.125,3.49 6.719,3.646 1.594,0.156 8 false 12.8 (131, 9) 1.094,2.125 1.458,2.344 0.365,0.219 8 false ● 0.229,1.854 2.677,2.01 2.448,0.156 8 false 6.9 (70, 61 in.*lbf) 2.896,0.281 3.177,0.635 0.281,0.354 18 false 4 1.281,3.5 2.875,3.656 1.594,0.156 8 false 15.6 (159, 12) 0.729,1.135 1.333,1.427 0.604,0.292 8 false 12 (122, 9) 2.979,3.469 3.344,3.688 0.365,0.219 10 false *1 4.885,3.51 5.042,3.708 0.156,0.198 8 false ★

Procedure Part Name Code
Z101186

Z101188

Z101187

1 INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY 84540 (Click here) - -
2 INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY 84540 (Click here) - -
3 TRANSMISSION CONTROL CABLE ASSEMBLY 33820B (Click here) - -
4 TRANSMISSION CONTROL CABLE INSULATOR 33825 (Click here) - -

*1 TRANSMISSION CONTROL SHAFT LEVER RH - -
V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf)
V100146

N*m (kgf*cm, ft.*lbf): Specified torque
● Non-reusable part
V100135

Toyota Genuine Adhesive 1344
★ Precoated part - -

PROCEDURE

Hide 84540 1.INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

Z101186

HINT:

Make sure that the manual valve lever shaft has not been rotated prior to installing the park/neutral position switch assembly as the detent spring may become detached from the manual valve lever shaft.



a.
C456961C01
4.313,2.948 4.896,2.948 true 4.563,3.583 4.729,3.583 4.729,3.583 5.188,3.104 true 0.365,0.125 0.917,0.479 0.552,0.354 18 false i, ii 0.292,1.969 0.979,2.302 0.688,0.333 18 true v - vii 4.052,2 4.75,2.396 0.698,0.396 18 false viii, ix 4.01,0.146 4.573,0.479 0.563,0.333 18 true iii, iv 4.177,4.063 4.854,4.396 0.677,0.333 18 true xi, xii 1.25,2 1.406,2.198 0.156,0.198 10 true N 4.167,2.833 4.479,3.031 0.313,0.198 10 false *a 0.333,4.031 0.552,4.406 0.219,0.375 18 false x 4.396,3.469 4.708,3.667 0.313,0.198 10 false *b
*a Neutral Basic Line *b Guide Pointer


i.

Clean the bolt and bolt hole.


ii.

Apply adhesive to 2 or 3 threads on the end of the bolt.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



iii.

Temporarily install the park/neutral position switch assembly with the bolt.

HINT:

Tighten the bolt to the specified torque when adjusting the park/neutral position switch assembly.



iv.

Install the lock washer and nut to the park/neutral position switch assembly.

Torque:
6.9 N*m (70 kgf*cm, 61 in.*lbf)


v.

Temporarily install the transmission control shaft lever RH to the manual valve lever shaft with the nut.

HINT:

Tighten the nut to the specified torque when adjusting the park/neutral position switch assembly.



vi.

Turn the transmission control shaft lever RH counterclockwise until it stops, and then turn it clockwise 2 notches to set it to the N position.


vii.

Remove the nut and transmission control shaft lever RH.


viii.

Align the guide pointer of the washer with the neutral basic line.


ix.

Hold the park/neutral position switch assembly in the position described above and tighten the bolt.

Torque:
12.8 N*m (131 kgf*cm, 9 ft.*lbf)


x.

Using a screwdriver, bend the tabs of the lock washer.

NOTICE:

Be careful not to damage the park/ neutral position switch assembly.



xi.

Install the transmission control shaft lever RH and spring washer with the nut.

Torque:
15.6 N*m (159 kgf*cm, 12 ft.*lbf)


xii.

Connect the park/neutral position switch connector.



Hide 84540 2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

Z101186

(Click here)

Hide 33820B 3.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C459122C01
4.583,0.583 5.417,0.583 5.417,0.583 5.417,0.75 false 4.385,0.469 4.698,0.625 0.313,0.156 10 false *a 4.177,2.677 4.49,2.833 0.313,0.156 10 false *b 0.385,0.135 0.552,0.51 0.167,0.375 18 true i 0.375,2.01 0.542,2.385 0.167,0.375 18 true ii
*a Clip *b 45° to 60°
V113147

Install in this Direction - -


i.

Connect the transmission control cable assembly to the transmission control shaft lever RH as shown in the illustration.

NOTICE:

Before installing the transmission control cable assembly, check that the park/neutral position switch assembly and shift lever are in N.



ii.

Connect the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.



Hide 33825 4.INSTALL TRANSMISSION CONTROL CABLE INSULATOR

Z101186

(Click here)