Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › IGNITION SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0467359 IGNITION SYSTEM G

V35A-FTS ENGINE CONTROL  IGNITION SYSTEM  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing an ignition coil assembly or spark plug.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 1.PERFORM SPARK TEST

CAUTION:
A379926

To prevent injury due to contact with an operating cooling fan, keep your hands and clothing away from the cooling fans when working in the engine compartment with the engine running or the ignition switch on (IG).


HINT:

Perform "Inspection After Repair" after replacing an ignition coil assembly or spark plug.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.

Check for DTCs.

NOTICE:

If any DTC is output, perform the troubleshooting procedures for that DTC.



b.

Remove the 6 ignition coil assemblies and 6 spark plugs.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>IGNITION COIL AND SPARK PLUG>REMOVAL

NOTICE:

If an ignition coil assembly or spark plug has been struck or dropped, replace it.



c.
A486425

Disconnect the 4 connectors.


d.

Install the spark plug to the ignition coil assembly and connect the ignition coil assembly connector.


e.

Ground the spark plug.


f.

Check that spark occurs at each spark plug while the engine is being cranked.

NOTICE:
·

Be sure to ground the spark plug when checking.

·

Replace the ignition coil assembly if it receives an impact.

·

Do not crank the engine for more than 2 seconds.



HINT:

If spark does not occur, perform the following procedure.



Hide 2.INSPECT IGNITION COIL ASSEMBLY AND SPARK TEST

HINT:

Perform "Inspection After Repair" after replacing a ignition coil assembly or spark plug.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.

Check that the ignition coil assembly connector is securely connected.

Result:
Result Action
NG Connect securely
OK Go to next step



b.

Perform a spark test on each ignition coil assembly.

i.

Replace the ignition coil assembly with a known good one.


ii.

Perform the spark test again.

Result:
Result Action
NG Go to next step
OK Replace ignition coil assembly


NOTICE:

If a ignition coil assembly or spark plug has been struck or dropped, replace it.




c.

Perform a spark test on each spark plug.

i.

Replace the spark plug with a known good one.


ii.

Perform the spark test again.

Result:
Result Action
NG Inspect the ignition system
(Click here)
OK Replace spark plug


NOTICE:

If a ignition coil assembly or spark plug has been struck or dropped, replace it.




d.

Connect the 4 connectors.


e.

Install the 6 ignition coil assemblies and 6 spark plugs.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>IGNITION COIL AND SPARK PLUG>INSTALLATION


f.

Check for DTCs.


g.

Clear the DTCs.


Hide 19100P 3.CHECK SPARK PLUG

NOTICE:
·

Do not damage the iridium tip and platinum tip.

·

Check the iridium tip visually since the iridium tip may be damaged.

·

Never attempt to adjust the electrode gap of a used spark plug.

·

Replace with new spark plugs if extremely dirty due to sludge, etc.

·

Replace with new spark plugs if damaged at all.

·

Replace with a new spark plug if it has been struck or dropped.

·

When replacing with a new spark plug, do not remove the cap for protecting the spark plug tip until it is installed to the engine.



HINT:

Perform "Inspection After Repair" after replacing a spark plug.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.
I039522C06
0.708,1.969 1.094,1.917 false 0.563,1.875 0.74,2.042 0.177,0.167 10 *a
*a Body Ground


Check the electrode.

i.

Using a megohmmeter, measure the insulation resistance.

Standard Insulation Resistance:
Tester Connection Condition Specified Condition
Spark plug (terminal part) - Body ground Always 10 MΩ or higher


HINT:
·

If the result is not as specified, clean the spark plug with a spark plug cleaner and measure the resistance again.

·

If a megohmmeter is not available, perform the following simple inspection instead.





b.

Alternative inspection method.

i.

Quickly accelerate the engine to 4000 rpm 5 times.



iii.

Visually check the spark plug.

If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.



c.

Check the spark plug for any damage to its threads and insulator.

If there is any damage, replace the spark plug.

Recommended Spark Plug:
Manufacturer Spark Plug Type
DENSO EC22HPR-D7



d.

Check the spark plug electrode gap.

Maximum Electrode Gap for Used Spark Plug:

0.9 mm (0.0354 in.)


NOTICE:

Never attempt to adjust the electrode gap of a used spark plug.


If the spark plug electrode gap is more than the maximum, replace the spark plug.

Standard Electrode Gap for New Spark Plug:

0.6 to 0.7 mm (0.0237 to 0.0275 in.)



e.

Clean the spark plugs.

If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.

Standard air pressure:

588 kPa (6.0 kgf/cm2, 85 psi)


Standard duration:

20 seconds or less


HINT:

Only use a spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.