Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM C

V35A-FTS ENGINE CONTROL  SFI SYSTEM  P030000  Random/Multiple Cylinder Misfire Detected  P030027  Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold  P030085  Random / Multiple Cylinder Misfire Detected (Over Temperature) Signal Above Allowable Range  P030100  Cylinder 1 Misfire Detected  P030200  Cylinder 2 Misfire Detected  P030300  Cylinder 3 Misfire Detected  P030400  Cylinder 4 Misfire Detected  P030500  Cylinder 5 Misfire Detected  P030600  Cylinder 6 Misfire Detected  


DESCRIPTION

When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high hydrocarbon concentration levels can cause an increase in exhaust emission levels. Extremely high concentrations of hydrocarbons can also cause increases in the three-way catalytic converter temperature, which may cause damage to the three-way catalytic converter. To prevent this increase in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire count. When the temperature of the three-way catalytic converter reaches the point of thermal degradation, the ECM blinks the MIL. To monitor misfires, the ECM uses both the camshaft position sensor and the crankshaft position sensor. The camshaft position sensor is used to identify any misfiring cylinders and the crankshaft position sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted when the crankshaft rotation speed variations exceed predetermined thresholds. If the misfire count exceeds the threshold levels, and could cause emission control system performance deterioration, the ECM illuminates the MIL and stores a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P030000 Random/Multiple Cylinder Misfire Detected Simultaneous misfiring of several cylinders occurs and one of the following conditions is met (2 trip detection logic):
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected).

·

An emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Port fuel injector assembly

·

Direct fuel injector assembly

·

Fuel pressure

·

Mass air flow meter sub-assembly

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

ECM


Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected.
SAE: P0300
P030027 Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold An emission deterioration misfire occurs (2 trip detection logic).
·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Port fuel injector assembly

·

Direct fuel injector assembly

·

Fuel pressure

·

Mass air flow meter sub-assembly

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

ECM


Comes on SAE: -
P030085 Random / Multiple Cylinder Misfire Detected (Over Temperature) Signal Above Allowable Range A misfire occurs that may damage the three-way catalytic converter (2 trip detection logic).
·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Port fuel injector assembly

·

Direct fuel injector assembly

·

Fuel pressure

·

Mass air flow meter sub-assembly

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

ECM


Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected.
SAE: -
P030100 Cylinder 1 Misfire Detected Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected).

·

An emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Port fuel injector assembly

·

Direct fuel injector assembly

·

Fuel pressure

·

Mass air flow meter sub-assembly

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

ECM


Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected.
SAE: P0301
P030200 Cylinder 2 Misfire Detected Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected).

·

An emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Port fuel injector assembly

·

Direct fuel injector assembly

·

Fuel pressure

·

Mass air flow meter sub-assembly

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

ECM


Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected.
SAE: P0302
P030300 Cylinder 3 Misfire Detected Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected).

·

An emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Port fuel injector assembly

·

Direct fuel injector assembly

·

Fuel pressure

·

Mass air flow meter sub-assembly

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

ECM


Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected.
SAE: P0303
P030400 Cylinder 4 Misfire Detected Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected).

·

An emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Port fuel injector assembly

·

Direct fuel injector assembly

·

Fuel pressure

·

Mass air flow meter sub-assembly

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

ECM


Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected.
SAE: P0304
P030500 Cylinder 5 Misfire Detected Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected).

·

An emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Port fuel injector assembly

·

Direct fuel injector assembly

·

Fuel pressure

·

Mass air flow meter sub-assembly

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

ECM


Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected.
SAE: P0305
P030600 Cylinder 6 Misfire Detected Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected).

·

An emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Port fuel injector assembly

·

Direct fuel injector assembly

·

Fuel pressure

·

Mass air flow meter sub-assembly

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

ECM


Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected.
SAE: P0306

When DTCs for misfiring cylinders are randomly stored, but DTC P030000 is not stored, it indicates that misfires have been detected in different cylinders at different times. DTC P030000 is only stored when several misfiring cylinders are detected at the same time.

MONITOR DESCRIPTION

The ECM illuminates the MIL and stores a DTC when the following condition, which could cause emission deterioration, is detected (2 trip detection logic).

·

An excessive number of misfires (approximately 10 to 70 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.


The ECM flashes the MIL (immediate detection logic) and stores a DTC (2 trip detection logic) when the following condition, which could cause damage to the three-way catalytic converter, is detected.

·

At a normal engine speed, a sufficient amount of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected 3 times.


MONITOR STRATEGY

Required Sensors/Components (Main) Crankshaft position sensor
Camshaft position sensor
Required Sensors/Components (Related) Engine coolant temperature
Intake air temperature sensor (mass air flow meter sub-assembly)
Mass air flow meter sub-assembly
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Misfire
Either of the following conditions is met (a) or (b)
(a) Engine coolant temperature at engine start Higher than -7°C (19°F)
(b) Engine coolant temperature Higher than 20°C (68°F)

Monitor Period of Emission-related Misfire
Duration Crankshaft 1000 revolutions x 4

Monitor Period of Catalyst-damaging Misfire (MIL Blinks)
Duration Crankshaft 200 revolutions x 3

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Record the DTC(s) and Freeze Frame Data.

5.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

6.

Using the GTS, switch the ECM from normal mode to check mode.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>CHECK MODE PROCEDURE

7.

Start the engine.

8.

Read the misfire counts of each cylinder, Misfire Count Cylinder #1 to Misfire Count Cylinder #6, with the engine idling. If any misfire count is displayed, skip the following confirmation driving pattern.

9.

Drive the vehicle so that the vehicle conditions displayed in Misfire RPM and Misfire Load of the Data List are the same as the Freeze Frame Data. Perform this step several times.

HINT:

In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below, confirm the Misfire RPM and Misfire Load in the Data List.

Engine speed Duration
Idling 8.0 minutes or more
1000 4.5 minutes or more
2000 2.5 minutes or more
3000 1.5 minutes or more


10.

Check whether misfires have occurred by checking DTCs and Freeze Frame Data.

HINT:

Do not turn the ignition switch off until the output DTC(s) and Freeze Frame Data have been recorded. When the ECM returns to normal mode (default), the stored DTC(s), Freeze Frame Data and other data are cleared.


11.

Record the DTC(s), Freeze Frame Data and misfire counts.

12.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

13.

Turn the ignition switch off and wait for at least 30 seconds.


WIRING DIAGRAM

Refer to DTC P010012 for the mass air flow meter sub-assembly circuit.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>P010012

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Check the "Fuel Cut Elapsed Time" in the Data List or the Freeze Frame Data.

If the elapsed time is over 0 seconds, then the engine speed is high (engine speed at which fuel cut occurs + 500 rpm).

When this has happened, there is the possibility that the valve rocker arm sub-assembly will become loose and a fire could start, so check that the valve rocker arm sub-assembly is properly attached.

·

By clearing the DTCs, "Fuel Cut Elapsed Time" will be cleared.

·

In the past, when the primary ignition system (the igniter drive circuit in the ECM, the primary circuit in the ignition coil assembly, the related wire harness, or the connector) was out of order, diagnostic codes from P035113 to P035613 were output. However, these codes are not output in this vehicle.

When a failure in the primary ignition system is suspected, refer to "Catalyst OT Misfire Fuel Cut History", "Catalyst OT Misfire Fuel Cut Cylinder #1 to #6", and "Misfire Count Cylinder #1 to #6" in the Freeze Frame Data, the pending Freeze Frame Data, and the Data List, and confirm in which cylinder the high-frequency misfire was concentrated.

·

Referring to the following contents of the Freeze Frame Data (or the pending Freeze Frame Data) enables an estimation of which cylinder has misfired and to what degree.

-

Misfire Count Cylinder #1 to #6: Misfire count according to cylinder.

-

Catalyst OT Misfire Fuel Cut Cylinder #1 to #6: This expresses a high-frequency misfire was concentrated in a certain cylinder and that cylinder's fuel injection was stopped.


·

If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.

·

If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the ECM as Freeze Frame Data.

·

If the misfire still cannot be reproduced even though the conditions stored in the ECM as Freeze Frame Data have been reproduced, one of the following factors is considered to be a possible cause of the problem:

(a)

There was insufficient fuel in the tank.

(b)

Improper fuel was used.

(c)

The spark plugs have been contaminated.

(d)

The problem requires further diagnosis.


·

After finishing repairs, check the misfire counts of the cylinders (Misfire Count Cylinder #1 to Misfire Count Cylinder #6).

·

Be sure to confirm that no misfiring cylinder DTCs are stored again by performing the confirmation driving pattern after finishing repairs.

·

For 6 cylinder engine, the ECM intentionally does not set the specific misfiring cylinder DTCs at high engine speed. If misfires occur only in high engine speed areas, only DTC P030000 is set.

In the event of DTC P030000 being present, perform the following operations:

(a)

Clear the DTCs.

(b)

Start the engine and conduct the confirmation driving pattern.

(c)

Read the misfiring counts of each cylinder or DTC(s) using the GTS.

(d)

Repair the cylinder(s) that has a high misfiring rate or is indicated by the DTC.

(e)

After finishing repairs, conduct the confirmation driving pattern again, in order to verify that DTC P030000 is not set.


·

When one of Short FT B1S1, Long FT B1S1, Short FT B2S1, Long FT B2S1 in the Freeze Frame Data is outside the range of +/-20%, the air fuel ratio may be rich (-20% or less) or lean (+20% or higher).

·

When Coolant Temperature in the Freeze Frame Data is less than 75°C (167°F), the misfires have occurred only while warming up the engine.

·

Vehicle body vibration caused by an extremely imbalanced drive wheel may cause misfire DTCs to be stored.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE DTCS)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
P030000, P030027, P030085, P030100, P030200, P030300, P030400, P030500 and/or P030600 are output A
P030000, P030027, P030085, P030100, P030200, P030300, P030400, P030500 and/or P030600 and other DTCs are output B


HINT:

If any DTCs other than P030000, P030027, P030085, P030100, P030200, P030300, P030400, P030500 and/or P030600 are output, troubleshoot those DTCs first.




A

2.CHECK PCV VALVE AND HOSE CONNECTIONS

B

GO TO DTC CHART

2.CHECK PCV VALVE AND HOSE CONNECTIONS
A485546

a.

Check the PCV hose connections.


b.

Check the PCV valve.

Click hereEngine / Hybrid System>V35A-FTS (EMISSION CONTROL)>PCV VALVE>ON-VEHICLE INSPECTION

OK:

PCV hose and PCV valve are connected correctly and are not damaged.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (MISFIRE RPM AND MISFIRE LOAD)

NG

REPAIR OR REPLACE PCV VALVE OR HOSE

3.READ VALUE USING GTS (MISFIRE RPM AND MISFIRE LOAD)
a.

Read and note the Misfire RPM and Misfire Load values.

Powertrain > Engine > Data List
Tester Display
Misfire RPM
Misfire Load
50003 372 146,152
HINT:

The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.



Result:
Proceed to
NEXT



NEXT

4.READ VALUE USING GTS (CATALYST OT MISFIRE FUEL CUT)
4.READ VALUE USING GTS (CATALYST OT MISFIRE FUEL CUT)
a.

Read the value displayed on the GTS.

Powertrain > Engine > Data List
Tester Display
Catalyst OT Misfire Fuel Cut
50003 372 154
Result:
Data List Result Proceed to
Catalyst OT Misfire Fuel Cut Avail A
Not Avi B




A

5.READ FREEZE FRAME DATA (CATALYST OT MISFIRE FUEL CUT HISTORY)

B

7.CHECK MISFIRE COUNT OF PORT INJECTION
5.READ FREEZE FRAME DATA (CATALYST OT MISFIRE FUEL CUT HISTORY)
a.

Using the GTS, confirm the vehicle conditions recorded in the Freeze Frame Data which were present when the DTC was stored.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA

Result:
Freeze Frame Data Item Result Proceed to
Catalyst OT Misfire Fuel Cut History ON A
OFF B




A

6.CHECK MISFIRE COUNT OF PORT INJECTION

B

7.CHECK MISFIRE COUNT OF PORT INJECTION
6.CHECK MISFIRE COUNT OF PORT INJECTION
a.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

Read each value for Misfire Count Cylinder #1 to Misfire Count Cylinder #6 and Injection Mode displayed on the GTS while performing the Active Test.

Powertrain > Engine > Active Test
Active Test Display
Prohibit the Catalyst OT Misfire Prevent Fuel Cut
Data List Display
Injection Mode
Misfire Count Cylinder #1
Misfire Count Cylinder #2
Misfire Count Cylinder #3
Misfire Count Cylinder #4
Misfire Count Cylinder #5
Misfire Count Cylinder #6
50004 372 42003 294,411,412,413,414,415,416
Result:
Injection Mode Misfire Count Proceed to
Port 1 or 2 cylinders have misfire counts A
3 cylinders or more have misfire counts
There are no misfire counts B




A

8.CHECK MISFIRE COUNT OF DIRECT INJECTION

B

11.CHECK MISFIRE COUNT OF DIRECT INJECTION
7.CHECK MISFIRE COUNT OF PORT INJECTION
a.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

According to the display on the GTS, read the Data List with the Active Test "Control the Injection Mode" set to Port. If no misfire counts occur in any cylinders, perform procedure [A] and [B] and then check the misfire counts again.

Powertrain > Engine > Active Test
Active Test Display
Control the Injection Mode
Data List Display
Injection Mode
Misfire Count Cylinder #1
Misfire Count Cylinder #2
Misfire Count Cylinder #3
Misfire Count Cylinder #4
Misfire Count Cylinder #5
Misfire Count Cylinder #6
50004 372 42004 294,411,412,413,414,415,416
i.

Drive the vehicle with the Misfire RPM and Misfire Load noted in the "Read Value Using GTS (Misfire RPM and Misfire Load)" procedures above [A].


ii.

Read the Injection Mode and Misfire Count Cylinder #1 to Misfire Count Cylinder #6 or DTCs displayed on the GTS [B].



Result:
Injection Mode Misfire Count Proceed to
Port 1 or 2 cylinders have misfire counts A
3 cylinders or more have misfire counts
There are no misfire counts B



A

8.CHECK MISFIRE COUNT OF DIRECT INJECTION

B

11.CHECK MISFIRE COUNT OF DIRECT INJECTION
8.CHECK MISFIRE COUNT OF DIRECT INJECTION
a.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

According to the display on the GTS, read the Data List with the Active Test "Control the Injection Mode" set to Direct. If no misfire counts occur in any cylinders, perform procedure [A] and [B] and then check the misfire counts again.

Powertrain > Engine > Active Test
Active Test Display
Control the Injection Mode
Data List Display
Injection Mode
Misfire Count Cylinder #1
Misfire Count Cylinder #2
Misfire Count Cylinder #3
Misfire Count Cylinder #4
Misfire Count Cylinder #5
Misfire Count Cylinder #6
50004 372 42004 294,411,412,413,414,415,416
i.

Drive the vehicle with the Misfire RPM and Misfire Load noted in the "Read Value Using GTS (Misfire RPM and Misfire Load)" procedures above [A].


ii.

Read the Injection Mode and Misfire Count Cylinder #1 to Misfire Count Cylinder #6 or DTCs displayed on the GTS [B].



Result:
Misfire Count Proceed to
Port (Result of step 6 or 7) Direct
1 or 2 cylinders have misfire counts 1 or 2 cylinders have misfire counts A
3 cylinders or more have misfire counts 3 cylinders or more have misfire counts B
1 or 2 cylinders have misfire counts There are no misfire counts C
3 cylinders or more have misfire counts There are no misfire counts D


HINT:

Perform "Inspection After Repair" after replacing the port fuel injector assembly.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



A

14.INSPECT SPARK PLUG

B

17.CHECK INTAKE SYSTEM

C

REPLACE PORT FUEL INJECTOR ASSEMBLY (MISFIRING CYLINDER)

D

9.CHECK FUEL PRESSURE (FOR LOW PRESSURE SIDE)
9.CHECK FUEL PRESSURE (FOR LOW PRESSURE SIDE)

Click hereEngine / Hybrid System>V35A-FTS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the port fuel injector assembly.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
OK
NG



OK

REPLACE PORT FUEL INJECTOR ASSEMBLY (MISFIRING CYLINDER)

NG

10.CHECK FUEL LINE
10.CHECK FUEL LINE
a.

Check the fuel lines for leaks or blockage.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE FUEL SYSTEM

11.CHECK MISFIRE COUNT OF DIRECT INJECTION
a.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

According to the display on the GTS, read the Data List with the Active Test "Control the Injection Mode" set to Direct. If no misfire counts occur in any cylinders, perform procedure [A] and [B] and then check the misfire counts again.

Powertrain > Engine > Active Test
Active Test Display
Control the Injection Mode
Data List Display
Injection Mode
Misfire Count Cylinder #1
Misfire Count Cylinder #2
Misfire Count Cylinder #3
Misfire Count Cylinder #4
Misfire Count Cylinder #5
Misfire Count Cylinder #6
50004 372 42004 294,411,412,413,414,415,416
i.

Drive the vehicle with the Misfire RPM and Misfire Load noted in the "Read Value Using GTS (Misfire RPM and Misfire Load)" procedures above [A].


ii.

Read the Injection Mode and Misfire Count Cylinder #1 to Misfire Count Cylinder #6 or DTCs displayed on the GTS [B].



Result:
Misfire Count Proceed to
Port (Result of step 6 or 7) Direct
There are no misfire counts There are misfire counts A
There are no misfire counts There are no misfire counts B


HINT:

Perform "Inspection After Repair" after replacing the direct fuel injector assembly.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



A

B

12.CLEAR DTC
12.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

13.CHECK MISFIRE COUNT
13.CHECK MISFIRE COUNT
a.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

Drive the vehicle with Misfire RPM and Misfire Load.


c.

Monitor all of the misfire count values and Injection Mode displayed on the GTS.

Powertrain > Engine > Data List
Tester Display
Injection Mode
Misfire Count Cylinder #1
Misfire Count Cylinder #2
Misfire Count Cylinder #3
Misfire Count Cylinder #4
Misfire Count Cylinder #5
Misfire Count Cylinder #6
Misfire RPM
Misfire Load
50003 372 294,411,412,413,414,415,416,146,152
Result:
Misfire Count Injection Mode Proceed to
There are no misfire counts - A
1 or 2 cylinders have misfire counts Port or Either B
3 cylinders or more have misfire counts Port or Either C
There are misfire counts Direct D


HINT:

Perform "Inspection After Repair" after replacing the direct fuel injector assembly.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




A

B

14.INSPECT SPARK PLUG

C

17.CHECK INTAKE SYSTEM

D

14.INSPECT SPARK PLUG
a.

Inspect the spark plug of the misfiring cylinder.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the spark plug.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

15.CHECK FOR SPARK (SPARK TEST)

NG

15.CHECK FOR SPARK (SPARK TEST)

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:
·

If the result of the spark test is normal, proceed to the next step.

·

Perform "Inspection After Repair" after replacing the spark plug or ignition coil assembly.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

16.CHECK CYLINDER COMPRESSION PRESSURE
16.CHECK CYLINDER COMPRESSION PRESSURE
a.

Measure the cylinder compression pressure of the misfiring cylinder.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION

HINT:

Perform "Inspection After Repair" after repairing or replacing the engine assembly.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

17.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

Click hereEngine / Hybrid System>V35A-FTS (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks from intake system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

18.READ VALUE USING GTS (COOLANT TEMPERATURE)

NG

REPAIR OR REPLACE INTAKE SYSTEM

18.READ VALUE USING GTS (COOLANT TEMPERATURE)
a.

Read the Data List twice, when the engine is both cold and warmed up.

Powertrain > Engine > Data List
Tester Display
Coolant Temperature
50003 372 205
Standard:
GTS Display Condition Specified Condition
Coolant Temperature Cold engine Same as ambient air temperature
Warm engine Between 75 and 100°C (167 and 212°F)


HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

19.READ VALUE USING GTS (MAF SENSOR)

NG

19.READ VALUE USING GTS (MAF SENSOR)
a.

Start the engine.


b.

Allow the engine to idle until Coolant Temperature reaches 75°C (167°F) or higher.


c.

Read Mass Air Flow Sensor while maintaining an engine speed of 3000 rpm.

Powertrain > Engine > Data List
Tester Display
MAF Sensor Bank1
MAF Sensor Bank2
50003 372 611,612
Standard:
GTS Display Condition Specified Condition
MAF Sensor Bank1 Engine warmed up
Shift position: N
A/C: Off
Engine Speed: 3000 rpm
Between 6.5 and 30.0 gm/sec
MAF Sensor Bank2 Between 6.5 and 30.0 gm/sec



Result:
Proceed to
OK
NG



OK

20.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN)

NG

21.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)
20.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN)
a.

Remove the cylinder head cover sub-assembly and cylinder head cover sub-assembly LH.

A472469C01
5.802,0.688 6.552,0.594 false 6.552,0.594 6.74,1.51 false 0.667,0.604 1.521,0.813 false 0.458,1.573 0.656,0.604 false 0.885,2.458 1.083,2.458 1.083,2.458 1.292,2.948 false 6.792,3.094 6.948,3.094 6.948,3.094 6.885,3.74 false 6.177,2.479 6.021,2.479 6.021,2.479 5.896,2.969 false 0.323,3.104 0.156,3.104 0.156,3.104 0.292,3.74 false 3.573,4.365 3.99,4.052 3.99,4.052 4.219,4.052 false 0.49,0.469 0.802,0.625 0.313,0.156 10 false *a 0.365,3.021 0.677,3.177 0.313,0.156 10 false *b 0.688,2.385 1,2.542 0.313,0.156 10 false *c 6.229,2.427 6.542,2.583 0.313,0.156 10 false *d 6.625,3.021 6.875,3.219 0.25,0.198 10 false *e 6.563,0.438 6.875,0.594 0.313,0.156 10 false *a 4.24,3.958 4.448,4.177 0.208,0.219 10 true *a
*a Timing Mark *b Approximately 48°
*c Approximately 17° *d Approximately 14°
*e Approximately 50° - -



b.

Turn the crankshaft pulley and align its groove with the TDC timing mark of the timing chain cover.


c.

Check that the timing marks of the camshaft timing gear assemblies and camshaft timing exhaust gear assemblies are at the positions shown in the illustration.

HINT:

If the timing marks are not as shown, turn the crankshaft one revolution clockwise.


OK:

Timing marks on camshaft timing gear assemblies and camshaft timing exhaust gear assemblies are at the positions shown in the illustration.


HINT:

If the result is not as specified, check for mechanical malfunctions that may have affected the valve timing, such as a jumped tooth or stretching of the timing chain.



Result:
Proceed to
OK
NG



OK

21.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

21.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)
a.

Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter sub-assembly and ECM.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

HINT:

Repair any problems.



Result:
Proceed to
NEXT



NEXT

22.CLEAR DTC
22.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

23.CHECK WHETHER DTC OUTPUT RECURS (MISFIRE DTCS)
23.CHECK WHETHER DTC OUTPUT RECURS (MISFIRE DTCS)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Perform the All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 1020

c.

Input the DTC: P030000, P030027, P030085, P030100, P030200, P030300, P030400, P030500 or P030600.


d.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(P030000, P030027, P030085, P030100, P030200, P030300, P030400, P030500 and/or P030600 is output)
B




A

END

B

24.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
24.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C24,C37,C25)Location & Routing

Click Connector(C24)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Intake Mass Air Flow Meter Sub-Assembly RH

Click Connector(C37)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

Click Connector(C25)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Intake Mass Air Flow Meter Sub-Assembly LH

C24-4 (VCCR) - C37-84 (VCVG) Always Below 1 Ω
C24-3 (FGR) - C37-78 (VG) Always Below 1 Ω
C24-2 (E2GR) - C37-83 (E2G) Always Below 1 Ω
C25-4 (VCC) - C37-82 (VVG2) Always Below 1 Ω
C25-3 (FG) - C37-76 (VG2) Always Below 1 Ω
C25-2 (E2G) - C37-81 (E2G2) Always Below 1 Ω
C24-4 (VCCR) or C37-84 (VCVG) - Body ground and other terminals Always 10 kΩ or higher
C24-3 (FGR) or C37-78 (VG) - Body ground and other terminals Always 10 kΩ or higher
C25-4 (VCC) or C37-82 (VVG2) - Body ground and other terminals Always 10 kΩ or higher
C25-3 (FG) or C37-76 (VG2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

25.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

25.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL

HINT:
·

If the results of the inspections performed in step 19 (READ VALUE USING GTS (MASS AIR FLOW SENSOR)) indicate no problem, proceed to the next step without replacing the mass air flow meter sub-assembly.

·

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

26.CLEAR DTC
26.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

27.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
27.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Perform the All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 1020

c.

Input the DTC: P030000, P030027, P030085, P030100, P030200, P030300, P030400, P030500 or P030600.


d.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(P030000, P030027, P030085, P030100, P030200, P030300, P030400, P030500 and/or P030600 is output)
B




A

END

B