Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › ENGINE COOLANT TEMPERATURE SENSOR
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0467371 ENGINE COOLANT TEMPERATURE SENSOR A

V35A-FTS ENGINE CONTROL  ENGINE COOLANT TEMPERATURE SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
A486397N01
1.635,1.635 1.885,1.406 1.885,1.406 2.115,1.406 false 1.323,1.5 1.604,1.5 false 6.552,0.229 6.865,0.229 false 6.552,0.948 6.813,0.948 false 6.542,0.615 6.865,0.615 false 3.052,0.563 3.438,0.563 false 2.208,1.313 2.365,1.51 0.156,0.198 10 false ● 1.135,1.365 1.417,1.719 0.281,0.354 18 false 1 2.875,0.417 3.156,0.771 0.281,0.354 18 false 2 6.344,0.479 6.625,0.833 0.281,0.354 18 false 3 6.344,0.115 6.625,0.469 0.281,0.354 18 false 4 6.344,0.844 6.521,1.188 0.177,0.344 18 false 5

Procedure Part Name Code
Z101186

Z101188

Z101187

1 E.F.I. ENGINE COOLANT TEMPERATURE SENSOR 89422 (Click here) - -
2 V-BANK COVER SUB-ASSEMBLY 11209 - - -
3 ADD ENGINE COOLANT - - (Click here) -
4 INSPECT FOR COOLANT LEAK - (Click here) - -
5 PERFORM INITIALIZATION - - - (Click here)

● Non-reusable part - -

CAUTION / NOTICE / HINT

PROCEDURE

Hide 89422 1.INSTALL E.F.I. ENGINE COOLANT TEMPERATURE SENSOR

a.
A486398C01
0.604,0.083 0.885,0.438 0.281,0.354 18 false i 3.76,0.083 4.042,0.438 0.281,0.354 18 false ii 0.281,1.917 0.656,2.271 0.375,0.354 18 false iii 5.094,3.292 5.406,3.49 0.313,0.198 10 false *a 4.458,2.51 4.771,2.708 0.313,0.198 10 false *b 5.281,3.125 5.51,3.323 0.229,0.198 10 false 30° 4.896,3.125 5.125,3.323 0.229,0.198 10 false 30°
*a FRONT *b RIGHT HAND


i.

Apply a light coat of engine coolant to the O-ring of the E.F.I engine coolant temperature sensor.


ii.

Install the E.F.I engine coolant temperature sensor to the water outlet pipe water by-pass joint with a new clip.

NOTICE:
·

If the E.F.I engine coolant temperature sensor has been struck or dropped, replace it.

·

If reusing the E.F.I engine coolant temperature sensor, be sure to inspect the O-ring.

·

Make sure that the O-ring is not cracked or moved out of place when installing the E.F.I engine coolant temperature sensor.




iii.

Connect the E.F.I engine coolant temperature sensor connector.



Hide 3.ADD ENGINE COOLANT

Hide 5.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION