Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › HEATED OXYGEN SENSOR
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0467390 HEATED OXYGEN SENSOR A

1GR-FE ENGINE CONTROL  HEATED OXYGEN SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
A489126N02
2.917,0.615 3.781,0.958 0.865,0.344 5.552,2.375 6.333,2.729 0.781,0.354 2.521,0.781 2.917,0.781 false 5.271,2.542 5.542,2.542 false 1.406,1.469 1.406,2.021 true 6.24,0.323 6.823,0.323 false 6.188,0.688 6.771,0.688 false 4.156,2.74 4.156,3.292 true 6.688,2.417 6.969,2.771 0.281,0.354 18 false 1 4.156,0.635 4.438,0.99 0.281,0.354 18 false 2 0,0 0.281,0.354 0.281,0.354 18 false 4 1.323,2.073 1.604,2.427 0.281,0.354 18 false 4 6.01,0.198 6.292,0.552 0.281,0.354 18 false 5 6.01,0.573 6.292,0.927 0.281,0.354 18 false 6 5.604,2.406 6.375,2.563 0.771,0.156 8 false 44 (449, 32) 3.031,0.646 3.802,0.802 0.771,0.156 8 false 44 (449, 32) 3.031,0.802 3.802,0.958 0.771,0.156 8 false 38 (387, 28)* 5.583,2.573 6.354,2.729 0.771,0.156 8 false 38 (387, 28)* 4.094,3.292 4.375,3.646 0.281,0.354 18 false 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 HEATED OXYGEN SENSOR (for Bank 2) 89465 (Click here) - -
2 HEATED OXYGEN SENSOR (for Bank 1) 89465A (Click here) - -
3 EXHAUST MANIFOLD ASSEMBLY LH 17150 - - -
4 EXHAUST MANIFOLD ASSEMBLY RH 17140 - - -
5 INSPECT FOR EXHAUST GAS LEAK - (Click here) - -
6 PERFORM INITIALIZATION - - - (Click here)

V100146

N*m (kgf*cm, ft.*lbf): Specified torque * For use with SST

PROCEDURE

Hide 89465 1.INSTALL HEATED OXYGEN SENSOR (for Bank 2)

a.
A486923C03
4.198,1.104 4.927,1.104 true 3.115,0.385 3.427,0.583 0.313,0.198 10 false *a 0.552,0.115 0.833,0.573 0.281,0.458 18 false i 4.969,1.031 5.427,1.229 0.458,0.198 10 false SST
*a Torque Wrench Fulcrum Length - -


i.

Using SST, install the heated oxygen sensor to the front exhaust pipe.

SST
09224-00012  

Torque:
Specified tightening torque : 44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:

Do not damage the heated oxygen sensor.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 37.7 N*m (384 kgf*cm, 28 ft.*lbf)





Hide 89465A 2.INSTALL HEATED OXYGEN SENSOR (for Bank 1)

a.
A486922C03
2.229,1.094 3.052,1.094 true 3.885,0.302 4.198,0.5 0.313,0.198 10 false *a 0.51,0.115 0.792,0.448 0.281,0.333 18 false i 1.896,1.021 2.354,1.219 0.458,0.198 10 true SST
*a Torque Wrench Fulcrum Length - -


i.

Using SST, install the heated oxygen sensor to the front exhaust pipe.

SST
09224-00012  

Torque:
Specified tightening torque : 44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:

Do not damage the heated oxygen sensor.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 37.7 N*m (384 kgf*cm, 28 ft.*lbf)





Hide 17150 3.INSTALL EXHAUST MANIFOLD ASSEMBLY LH

Hide 17140 4.INSTALL EXHAUST MANIFOLD ASSEMBLY RH

Hide 6.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION