Home › Drivetrain › JF2BM (TRANSFER / 4WD / AWD) › TRANSFER SYSTEM
RM38G0E _52 Drivetrain _100437 JF2BM TRANSFER / 4WD / AWD _0467431 TRANSFER SYSTEM C

JF2BM TRANSFER / 4WD / AWD  TRANSFER SYSTEM  P17DF62  4WD/AWD Center Differential Lock Limit Switch Signal Compare Failure  


DESCRIPTION

When the transfer shift actuator assembly is switching between free and lock, the TL2 and TL3 terminals are in one of the ON/OFF combinations listed in the table below.

Terminal Mode
FREE Switching LOCK
TL2 OFF ON ON
TL3 ON ON OFF

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
P17DF62 4WD/AWD Center Differential Lock Limit Switch Signal Compare Failure
Diagnosis Condition:
·

When switching between free and lock (center differential lock shift motor operating) while the ignition switch is turned to ON or directly after the ignition switch is turned to ON


Malfunction Status:
·

The combination of TL2 and TL3 does not match


Malfunction Time:
·

0.05 seconds or more (if directly after ignition switch is turned to ON, 1 second or more)


Number of Trips:
·

1 trip


·

Wire harness and connector

·

Transfer shift actuator assembly

·

4 wheel drive control ECU


Four Wheel Drive

DTC Detection Conditions:
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition When switching between free and lock (center differential lock shift motor operating) while the ignition switch is turned to ON ○ -
When switching between free and lock (center differential lock shift motor operating) while the directly after the ignition switch is turned to ON - ○
Malfunction Status The combination of TL2 and TL3 does not match ○ ○
Detection Time 0.05 seconds or more 1 second or more
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C339925E12
1.51,2.365 2.927,2.948 1.417,0.583 10 false Center Differential Lock Limit Switch 1.177,3.24 3.917,3.646 2.74,0.406 10 false Center Differential Lock Shift Actuator (Transfer Shift Actuator Assembly) 1.156,3.052 1.615,3.281 0.458,0.229 10 false C47 3.094,1.323 3.417,1.552 0.323,0.229 10 false TL2 3.115,1.99 3.542,2.271 0.427,0.281 10 false TL3 3.427,1.313 3.719,1.49 0.292,0.177 10 false 6 3.417,1.99 3.635,2.24 0.219,0.25 10 false 5 1.198,2.01 1.719,2.177 0.521,0.167 10 false GND1 1,1.979 1.219,2.146 0.219,0.167 10 false 4 5,3.24 6.958,3.5 1.958,0.26 10 false 4 Wheel Drive Control ECU 5,3.031 5.354,3.229 0.354,0.198 10 false B8 4.75,1.292 5.021,1.438 0.271,0.146 10 false 8 4.979,1.99 5.406,2.271 0.427,0.281 10 false TL3 4.969,1.302 5.292,1.531 0.323,0.229 10 false TL2 4.75,1.979 5.073,2.188 0.323,0.208 10 false 7 5.677,0.313 6.052,0.594 0.375,0.281 10 false IG

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - CENTER DIFFERENTIAL LOCK SHIFT ACTUATOR (TRANSFER SHIFT ACTUATOR ASSEMBLY))
a.

Disconnect the B8 4 wheel drive control ECU connector.


b.

Disconnect the C47 center differential lock shift actuator (transfer shift actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B8,C47)Location & Routing

Click Connector(B8)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>4 Wheel Drive Control ECU

Click Connector(C47)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Transfer Assembly

B8-8 (TL2) - C47-6 (TL2) Always Below 1 Ω
B8-7 (TL3) - C47-5 (TL3) Always Below 1 Ω
C47-4 (GND1) - Body ground Always Below 1 Ω
B8-8 (TL2) or C47-6 (TL2) - Body ground Always 10 kΩ or higher
B8-7 (TL3) or C47-5 (TL3) - Body ground Always 10 kΩ or higher



d.

Connect the B8 4 wheel drive control ECU connector.


e.

Connect the C47 center differential lock shift actuator (transfer shift actuator assembly) connector.


Result:
Proceed to
OK
NG



OK

2.CHECK 4 WHEEL DRIVE CONTROL ECU (ECU OUTPUT VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK 4 WHEEL DRIVE CONTROL ECU (ECU OUTPUT VOLTAGE)
a.

Disconnect the C47 center differential lock shift actuator (transfer shift actuator assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(C47)Location & Routing

Click Connector(C47)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Transfer Assembly

C47-6 (TL2) - Body ground Ignition switch ON 10 to 16 V
C47-5 (TL3) - Body ground Ignition switch ON 10 to 16 V



c.

Connect the C47 center differential lock shift actuator (transfer shift actuator assembly) connector.


Result:
Proceed to
OK
NG



OK

REPLACE TRANSFER SHIFT ACTUATOR ASSEMBLY

NG