| *1 | NO. 2 TRANSFER CASE PLUG | *2 | TRANSFER DRIVEN SPROCKET |
| *3 | REAR TRANSFER OUTPUT SHAFT | - | - |
| ● | Non-reusable part | ★ | Precoated part |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 10 | REAR TRANSFER CASE | 36112 | ( ) |
- | - |
| 11 | FRONT TRANSFER OUTPUT SHAFT NEEDLE ROLLER BEARING | 36231E | - | - | - |
| *1 | FRONT TRANSFER CASE | - | - |
| *1 | OIL PUMP GEAR | *2 | OIL PUMP PLATE SUB-ASSEMBLY |
| *3 | OIL PUMP SHAFT | *4 | OIL PUMP DRIVE ROTOR |
| *5 | OIL PUMP DRIVEN ROTOR | *6 | STRAIGHT PIN |
| *7 | TRANSFER CASE PLUG | *8 | STRAIGHT SCREW PLUG |
| *9 | TRANSFER CASE COMPRESSION SPRING | *10 | FRONT TRANSFER CASE |
| *11 | PIN | - | - |
| ● | Non-reusable part | ★ | Precoated part |
| *1 | NO. 2 TRANSFER SHIFT SHAFT STOPPER | *2 | NO. 2 TRANSFER GEAR SHIFT FORK |
| *3 | NO. 1 TRANSFER GEAR SHIFT FORK | *4 | TRANSFER SHIFT SHAFT STOPPER |
| *5 | REAR TRANSFER CASE | *6 | TRANSFER FRONT DRIVE CHAIN |
| *7 | TRANSFER DRIVEN SPROCKET | - | - |
| ● | Non-reusable part | - | - |
| *1 | TRANSFER LOW PLANETARY GEAR ASSEMBLY | *2 | TRANSFER INPUT SHAFT |
| *3 | TRANSFER OIL RECEIVER | - | - |
| ● | Non-reusable part | - | - |
| *1 | STRAIGHT PIN | *2 | CENTER DIFFERENTIAL CASE |
| *3 | FRONT DRIVE CLUTCH SLEEVE | *4 | TRANSFER DRIVE SPROCKET SUB-ASSEMBLY |
| *5 | REAR TRANSFER OUTPUT SHAFT | *6 | TRANSFER DRIVE SPROCKET BEARING (FRONT SIDE) |
| *7 | TRANSFER DRIVE SPROCKET BEARING (REAR SIDE) | - | - |
| ● | Non-reusable part | - | - |
1.REMOVE DRAIN PLUG
2.REMOVE FILLER PLUG
37109A 3.REMOVE PROPELLER SHAFT HEAT INSULATOR BRACKET SUB-ASSEMBLY
36115C 4.REMOVE TRANSFER EXTENSION HOUSING TYPE T OIL SEAL
Using a screwdriver, pry out the transfer extension housing type T oil seal.
Be careful not to damage the transfer input shaft and front transfer case.
5.REMOVE TRANSFER CASE PLUG
|
Transfer Case Plug |
|
No. 2 Transfer Case Plug |
Using a 14 mm straight hexagon wrench, remove the transfer case plug.
Using a 6 mm hexagon socket wrench, remove the No. 2 transfer case plug.
33309C 6.REMOVE OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY (FRONT)
Using SST and a hammer, release the staked part of the transfer output shaft nut.
Be sure to use SST with the tapered surface facing the shaft.
Do not grind the tip of SST with a grinder, etc.
Completely loosen the staked part of the nut when removing it.
Do not damage the threads of the transfer driven sprocket.
Using SST, hold the output shaft companion flange sub-assembly (front) and remove the transfer output shaft nut.
Using SST, remove the output shaft companion flange sub-assembly (front).
Remove the O-ring from the output shaft companion flange sub-assembly (front).
33309B 8.REMOVE OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY (REAR)
Using SST and a hammer, release the staked part of the transfer output shaft nut.
Be sure to use SST with the tapered surface facing the shaft.
Do not grind the tip of SST with a grinder, etc.
Completely loosen the staked part of the nut when removing it.
Do not damage the threads of the rear transfer output shaft.
Using SST, hold the output shaft companion flange sub-assembly (rear) and remove the transfer output shaft nut.
Using SST, remove the output shaft companion flange sub-assembly (rear).
Remove the O-ring from the output shaft companion flange sub-assembly (rear).
36112 10.REMOVE REAR TRANSFER CASE
Remove the 14 bolts. Using a brass bar and plastic-faced hammer, lightly tap and remove the rear transfer case.
Set the brass bar on the rib of the rear transfer case.
36231E 11.REMOVE FRONT TRANSFER OUTPUT SHAFT NEEDLE ROLLER BEARING
12.REMOVE TRANSFER OIL SEPARATOR SUB-ASSEMBLY
33449D 13.REMOVE TRANSFER CASE MAGNET
36106L 14.REMOVE TRANSFER OIL PUMP ROTOR SET
| *1 | Oil Pump Drive Rotor | *2 | Oil Pump Driven Rotor |
Using a 6 mm hexagon socket wrench, remove the straight screw plug from the oil pump plate sub-assembly.
There is no need to remove this unless the straight pin is replaced.
15.REMOVE TRANSFER INPUT SHAFT ASSEMBLY
Using a 14 mm straight hexagon wrench, remove the 2 transfer case plugs from the front transfer case.
Using SST, expand the shaft snap ring.
Remove the transfer input shaft assembly from the front transfer case.
36111M 16.REMOVE TRANSFER CASE SLOTTED SPRING PIN
| *1 | Transfer Case Plug | *2 | Transfer Case Compression Spring |
| *3 | Transfer Case Slotted Spring Pin | - | - |
36273 17.REMOVE TRANSFER LOW PLANETARY RING GEAR
Using a screwdriver, remove the transfer input shaft hole snap ring.
Remove the transfer low planetary ring gear from the front transfer case.
Using SST, remove the shaft snap ring from the front transfer case.
18.REMOVE TRANSFER OIL PUMP RELIEF VALVE SUB-ASSEMBLY
36292A 19.REMOVE TRANSFER DRIVEN SPROCKET BEARING
There is no need to remove this unless the pin is replaced.
Using a screwdriver, remove the transfer driven sprocket snap ring.
Using SST, remove the transfer driven sprocket bearing from the front transfer case.
36111T 20.REMOVE TRANSFER CASE TUBE
There is no need to remove this unless the transfer case tube is replaced.
36235 21.REMOVE TRANSFER HIGH AND LOW CLUTCH SLEEVE
| *1 | No. 2 Transfer Gear Shift Fork | *2 | Transfer High and Low Clutch Sleeve |
|
Remove in this direction | - | - |
36410J 22.REMOVE TRANSFER SHIFT ACTUATOR ASSEMBLY
| *1 | No. 1 Transfer Gear Shift Fork | *2 | Transfer Shift Shaft Stopper |
| *3 | Transfer Shift Actuator Assembly | - | - |
Using 2 screwdrivers and a hammer, tap out the 2 transfer gear shift fork snap rings.
Using a cloth, prevent the transfer gear shift fork snap ring from flying off.
Remove the 2 No. 1 transfer gear shift fork and transfer shift shaft stopper installation bolts.
Remove the 3 transfer shift actuator assembly installation bolts.
Remove the transfer shift actuator assembly, No. 1 transfer gear shift fork and transfer shift shaft stopper.
Take care not to drop the No. 1 transfer gear shift fork and transfer shift shaft stopper.
Remove the O-ring from the transfer shift actuator assembly.
23.REMOVE REAR TRANSFER OUTPUT SHAFT ASSEMBLY
| *1 | Rear Transfer Output Shaft Assembly | *2 | Transfer Front Drive Chain |
| *3 | Transfer Driven Sprocket | - | - |
|
Expand | - | - |
Using SST, expand the transfer output shaft snap ring as shown in the illustration.
Using a plastic-faced hammer, carefully tap the rear transfer case, and remove the transfer front drive chain, transfer driven sprocket and rear transfer output shaft assembly.
Do not drop the transfer output shaft washers.
Using a snap ring expander, remove the transfer output shaft snap ring from the rear transfer case.
41335D 24.REMOVE SIDE GEAR SHAFT HOLDER BEARING
Using a screwdriver, remove the transfer driven sprocket snap ring.
Using SST, remove the side gear shaft holder bearing.
36111G 25.REMOVE TRANSFER CASE STRAIGHT PIN
There is no need to remove this unless the transfer case straight pin is replaced.
36216A 26.REMOVE NO. 1 TRANSFER INPUT SHAFT SEAL RING
36210A 27.REMOVE TRANSFER INPUT SHAFT BEARING
| *1 | Transfer Input Shaft Bearing | *2 | Transfer Low Planetary Gear Assembly |
| *3 | Manual Transfer Planetary Carrier Washer | - | - |
Using a snap ring expander, remove the transfer input bearing shaft snap ring.
Using SST and a press, press out the transfer input shaft bearing, transfer low planetary gear assembly and 2 manual transfer planetary carrier washers from the transfer input shaft.
Be careful not to drop or damage the transfer input shaft, transfer low planetary gear assembly and transfer input shaft bearing.
36212B 28.REMOVE TRANSFER INPUT GEAR NEEDLE ROLLER BEARING
Using SST, remove the transfer input gear needle roller bearing.
36218C 29.REMOVE TRANSFER INPUT SHAFT PLUG
| *1 | Transfer Input Shaft Plug | *2 | Transfer Oil Receiver |
Using SST and a hammer, tap out the transfer input shaft plug and transfer oil receiver from the transfer input shaft.
33309H 30.REMOVE TRANSFER OUTPUT SHAFT WASHER
36255 31.REMOVE NO. 1 TRANSFER OUTPUT SHAFT SPACER
Using 2 screwdrivers and a hammer, tap out the transfer input gear shaft snap ring.
Remove the No. 1 transfer output shaft spacer from the rear transfer output shaft.
Remove the straight pin from the rear transfer output shaft.
32.REMOVE CENTER DIFFERENTIAL CASE, FRONT DRIVE CLUTCH SLEEVE AND TRANSFER DRIVE SPROCKET SUB-ASSEMBLY
| *1 | Center Differential Case | *2 | Front Drive Clutch Sleeve |
| *3 | Transfer Drive Sprocket Sub-assembly | - | - |
Remove the center differential case, front drive clutch sleeve and transfer drive sprocket sub-assembly from the rear transfer output shaft.
Remove the front drive clutch sleeve and transfer drive sprocket sub-assembly from the center differential case.
36291A 33.REMOVE TRANSFER DRIVE SPROCKET BEARING
| *1 | Transfer Drive Sprocket Bearing (Front Side) | *2 | Transfer Drive Sprocket Bearing (Rear Side) |
|
Expand the opening |
|
Remove in this direction |
36231J 34.REMOVE TRANSFER OUTPUT SHAFT REAR RADIAL BALL BEARING
Using SST and a press, press out the transfer output shaft rear radial ball bearing.
Be careful not to drop or damage the rear transfer output shaft.