Home › Drivetrain › JF2BM (TRANSFER / 4WD / AWD) › TRANSFER SYSTEM
RM38G0E _52 Drivetrain _100437 JF2BM TRANSFER / 4WD / AWD _0467431 TRANSFER SYSTEM C

JF2BM TRANSFER / 4WD / AWD  TRANSFER SYSTEM  P17FA9E  4WD/AWD Front Differential Lock Switch "A" Stuck On  P17FA9F  4WD/AWD Front Differential Lock Switch "A" Stuck Off  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
P17FA9E 4WD/AWD Front Differential Lock Switch "A" Stuck On
Diagnosis Condition:
·

With ignition switch turned to ON


Malfunction Status:
·

With vehicle speed higher than 0 km/h (0 mph), differential of front wheel speed 1 km/h (0.6 mph) or higher, front differential lock position sensor (No. 1 4 wheel drive position switch) is stuck ON


Malfunction Time:
·

2 seconds or more


Number of Trips:
·

1 trip


·

Wire harness and connector

·

Front differential lock position sensor (No. 1 4 wheel drive position switch)

·

4 wheel drive control ECU


Four Wheel Drive
P17FA9F 4WD/AWD Front Differential Lock Switch "A" Stuck Off
Diagnosis Condition:
·

With ignition switch turned to ON, front differential is locked (front differential lock solenoid (No. 1 front differential case sub-assembly) operating)


Malfunction Status:
·

With vehicle speed 5 km/h (3.1 mph) or higher, differential of front wheel speed 3 km/h (1.8 mph) or lower, front differential lock position sensor (No. 1 4 wheel drive position switch) is stuck OFF


Malfunction Time:
·

120 seconds or more


Number of Trips:
·

1 trip


·

Wire harness and connector

·

Front differential lock position sensor (No. 1 4 wheel drive position switch)

·

4 wheel drive control ECU


Four Wheel Drive

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - FRONT DIFFERENTIAL LOCK POSITION SENSOR (NO. 1 4 WHEEL DRIVE POSITION SWITCH))
a.

Disconnect the B8 4 wheel drive control ECU connector.


b.

Disconnect the H2 front differential lock position sensor (No. 1 4 wheel drive position switch) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B8,H2)Location & Routing

Click Connector(B8)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>4 Wheel Drive Control ECU

Click Connector(H2)Engine Compartment>Differential Wire>Differential Position Switch (Front Differential Assembly)

B8-1 (FLP) - H2-1 (SLV) Always Below 1 Ω
B8-11 (SPS) - H2-2 (SLS) Always Below 1 Ω
B8-12 (SG) - H2-3 (GND) Always Below 1 Ω
B8-1 (FLP) or H2-1 (SLV) - Body ground Always 10 kΩ or higher
B8-11 (SPS) or H2-2 (SLS) - Body ground Always 10 kΩ or higher



d.

Connect the H2 front differential lock position sensor (No. 1 4 wheel drive position switch) connector.


e.

Connect the B8 4 wheel drive control ECU connector.


Result:
Proceed to
OK
NG



OK

2.CHECK 4 WHEEL DRIVE CONTROL ECU (ECU OUTPUT VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK 4 WHEEL DRIVE CONTROL ECU (ECU OUTPUT VOLTAGE)
a.

Disconnect the H2 front differential lock position sensor (No. 1 4 wheel drive position switch) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(H2)Location & Routing

Click Connector(H2)Engine Compartment>Differential Wire>Differential Position Switch (Front Differential Assembly)

H2-1 (SLV) - Body ground Ignition switch ON 4.6 to 5.4 V



c.

Connect the H2 front differential lock position sensor (No. 1 4 wheel drive position switch) connector.


Result:
Proceed to
OK
NG



OK

3.INSPECT FRONT DIFFERENTIAL LOCK POSITION SENSOR (NO. 1 4 WHEEL DRIVE POSITION SWITCH)

NG

3.INSPECT FRONT DIFFERENTIAL LOCK POSITION SENSOR (NO. 1 4 WHEEL DRIVE POSITION SWITCH)
a.

Turn the ignition switch off.


b.

Remove the front differential lock position sensor (No. 1 4 wheel drive position switch).


c.

Connect 3 1.5 V dry batteries in series.


d.
C456414C01
1.917,1.75 1.417,1.833 1.417,1.833 1.417,1.917 true 2.177,1.75 2.167,2.167 true 2.49,1.729 3,1.833 3,1.833 3,1.917 true 2.427,3.396 2.74,3.594 0.313,0.198 10 false *c 1.302,1.969 1.76,2.167 0.458,0.198 10 false GND 2.042,2.219 2.5,2.417 0.458,0.198 10 false SLS 2.885,1.979 3.344,2.177 0.458,0.198 10 false SLV 2.802,1.094 3.115,1.292 0.313,0.198 10 false *b 1.427,0.417 1.74,0.615 0.313,0.198 10 false *a
*a Dry Batteries
*b Component without harness connected
(Front Differential Lock Position Sensor (No. 1 4 Wheel Drive Position Switch))
*c Piece of Metal


Connect terminal 1 (SLV) to the batteries positive (+) terminal, and terminal 3 (GND) to the batteries negative (-) terminal.


e.

Move a piece of metal close to the edge of the front differential lock position sensor (No. 1 4 wheel drive position switch), and then move it away and check that the resistance changes.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (SLS) - 3 (GND) Low (Move piece of metal away) 300 to 400 Ω
2 (SLS) - 3 (GND) High (Move piece of metal closer) 2.2k to 2.4k Ω



g.

Install the front differential lock position sensor (No. 1 4 wheel drive position switch).


Result:
Proceed to
OK
NG



OK

NG

REPLACE NO. 1 4 WHEEL DRIVE POSITION SWITCH