Home › Drivetrain › JF2BM (TRANSFER / 4WD / AWD) › TRANSFER SYSTEM
RM38G0E _52 Drivetrain _100437 JF2BM TRANSFER / 4WD / AWD _0467431 TRANSFER SYSTEM C

JF2BM TRANSFER / 4WD / AWD  TRANSFER SYSTEM  P17FB62  4WD/AWD Transfer Case H-L Motor Limit Switch Signal Compare Failure  


DESCRIPTION

When the transfer shift actuator assembly is switching between high (H4) and low (L4), the HL1, HL2 and HL3 terminals are in one of the ON/OFF combinations listed in the table below.

Terminal Mode
High (H4) Switching Low (L4)
HL1 ON ON ←→ OFF ←→ OFF OFF
HL2 OFF OFF OFF ON ON
HL3 OFF ON ON ON OFF

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
P17FB62 4WD/AWD Transfer Case H-L Motor Limit Switch Signal Compare Failure
Diagnosis Condition:
·

When switching between high and low (high-low transfer shift motor operating) while the ignition switch is turned to ON or directly after the ignition switch is turned to ON


Malfunction Status:
·

The combination of HL1, HL2 and HL3 does not match


Malfunction Time:
·

0.05 seconds or more (if directly after ignition switch is turned to ON, 1 second or more)


Number of Trips:
·

1 trip


·

Wire harness and connector

·

Transfer shift actuator assembly

·

4 wheel drive control ECU


Four Wheel Drive

DTC Detection Conditions:
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition When switching between high and low (high-low transfer shift motor operating) while the ignition switch is turned to ON ○ -
When switching between high and low (high-low transfer shift motor operating) while the directly after the ignition switch is turned to ON - ○
Malfunction Status The combination of HL1, HL2 and HL3 does not match ○ ○
Detection Time 0.05 seconds or more 1 second or more
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C456188E02
5.01,4.24 5.323,4.438 0.313,0.198 10 false B8 5.01,4.5 6.792,4.74 1.781,0.24 10 false 4 Wheel Drive Control ECU 4.958,1.521 5.417,1.719 0.458,0.198 10 false HL1 4.688,1.51 4.896,1.708 0.208,0.198 10 false 6 4.667,2.406 4.875,2.604 0.208,0.198 10 false 5 4.979,2.417 5.438,2.615 0.458,0.198 10 false HL2 4.99,3.229 5.448,3.427 0.458,0.198 10 false HL3 4.583,3.24 4.896,3.438 0.313,0.198 10 false 15 2.885,1.531 3.344,1.729 0.458,0.198 10 false HL1 2.865,2.417 3.323,2.615 0.458,0.198 10 false HL2 2.844,3.229 3.302,3.427 0.458,0.198 10 false HL3 3.365,1.521 3.521,1.719 0.156,0.198 10 false 3 3.375,2.406 3.583,2.604 0.208,0.198 10 false 5 3.375,3.24 3.583,3.438 0.208,0.198 10 false 4 1.104,3.229 1.563,3.427 0.458,0.198 10 false GND 0.823,3.219 0.979,3.417 0.156,0.198 10 false 6 1.344,3.781 2.854,3.99 1.51,0.208 10 false High-low Limit Switch 0.979,4.448 1.438,4.646 0.458,0.198 10 false C48 1.031,4.698 3.042,5.146 2.01,0.448 10 false High-low Shift Actuator (Transfer Shift Actuator Assembly)

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - HIGH-LOW SHIFT ACTUATOR (TRANSFER SHIFT ACTUATOR ASSEMBLY))
a.

Disconnect the B8 4 wheel drive control ECU connector.


b.

Disconnect the C48 high-low shift actuator (transfer shift actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B8,C48)Location & Routing

Click Connector(B8)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>4 Wheel Drive Control ECU

Click Connector(C48)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Transfer Assembly

B8-6 (HL1) - C48-3 (HL1) Always Below 1 Ω
B8-5 (HL2) - C48-5 (HL2) Always Below 1 Ω
B8-15 (HL3) - C48-4 (HL3) Always Below 1 Ω
C48-6 (GND) - Body ground Always Below 1 Ω
B8-6 (HL1) or C48-3 (HL1) - Body ground Always 10 kΩ or higher
B8-5 (HL2) or C48-5 (HL2) - Body ground Always 10 kΩ or higher
B8-15 (HL3) or C48-4 (HL3) - Body ground Always 10 kΩ or higher



d.

Connect the C48 high-low shift actuator (transfer shift actuator assembly) connector.


e.

Connect the B8 4 wheel drive control ECU connector.


Result:
Proceed to
OK
NG



OK

2.CHECK 4 WHEEL DRIVE CONTROL ECU (ECU OUTPUT VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK 4 WHEEL DRIVE CONTROL ECU (ECU OUTPUT VOLTAGE)
a.

Disconnect the C48 high-low shift actuator (transfer shift actuator assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(C48)Location & Routing

Click Connector(C48)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Transfer Assembly

C48-3 (HL1) - Body ground Ignition switch ON 10 to 16 V
C48-5 (HL2) - Body ground Ignition switch ON 10 to 16 V
C48-4 (HL3) - Body ground Ignition switch ON 10 to 16 V



c.

Connect the C48 high-low shift actuator (transfer shift actuator assembly) connector.


Result:
Proceed to
OK
NG



OK

REPLACE TRANSFER SHIFT ACTUATOR ASSEMBLY

NG